On OMAP platforms, SATA controller provides the SCSI subsystem
so implement scsi_init().

Get rid of the unnecessary sata_init() call from dra7xx-evm
and omap5-uevm board files.
Signed-off-by: NRoger Quadros <rogerq@ti.com>

DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Set the active_slave to 1 as slave 1 is pinned out in dra72x base board
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>

Update the board_name env variable and accordingly
populate the dtb file.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

We previously only supported QSPI_1 (single) support.  Add QSPI_4 (quad)
read support as well.  This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value.  We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment.  When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>

Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also correct the bit masking of mac id read from the efuse.
Acked-by: NTom Rini <trini@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>

Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: NTom Rini <trini@ti.com>

Add the SATA boot support for OMAP5 and dra7xx.

Renamed the omap_sata_init to the common init_sata(int dev)
for commonality in with sata stack.

Added the ROM boot device ID for SATA.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Reviewed-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>

Byte offset of Ethernet mac address read from e-fuse are wrong so DHCP is
not working on some boards, modifying the offset to read properly.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>

The evm has a SATA port. Enable SATA configuration and
inititialize the SATA controller.
Signed-off-by: NRoger Quadros <rogerq@ti.com>

Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.
Signed-off-by: NDan Murphy <dmurphy@ti.com>

Adding support for CPSW Ethernet support found in DRA7xx EVM
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: NTom Rini <trini@ti.com>

TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs
Rename twl6035 to palmas to allow reuse across multiple current and
future platforms

As part of this change, change the CONFIG_TWL6035_POWER to
CONFIG_PALMAS_POWER and update usage of header file accordingly.
Signed-off-by: NNishanth Menon <nm@ti.com>

Adding new board files for DRA7XX socs.
The pad registers layout is changed completely from OMAP5
So introducing the new structure here and also adding the
minimal data.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NNishant Kamat <nskamat@ti.com>
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Reviewed-by: NTom Rini <trini@ti.com>
[trini: Adapt omap_mmc_init call for last 2 params]
Signed-off-by: NTom Rini <trini@ti.com>

Add check for write protection in omap mmc driver.
Signed-off-by: NNikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Reviewed-by: NTom Rini <trini@ti.com>

Implement driver check for card detection.
Signed-off-by: NNikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>

palmas/TWL6035 is power IC for omap5 evm boards
Signed-off-by: NBalaji T K <balajitk@ti.com>

Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency.  While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board.  The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: NJonathan Solnit <jsolnit@gmail.com>

This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.

OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.

Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.
Signed-off-by: Nsricharan <r.sricharan@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
  to SoC directory). Will help in having single SPL for all
  boards.
- Non-essential part(the pins not essential for u-boot to function)
  need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader
Signed-off-by: NAneesh V <aneesh@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Add battery charging support twl6030 driver.
Add support for battery voltage and current measurements.
Add command to get battery status and start/stop battery charging from USB.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Tested-by: NSteve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

This patch switches from the legacy mmc driver to the new generic mmc driver
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Tested-by: NSteve Sakoman <steve@sakoman.com>

Add functional multiplexing support for OMAP4 pads.
Configure all the pads for the OMAP4430 SDP
and OMAP4 Panda boards
Signed-off-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NAneesh V <aneesh@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

This patch adds a gpmc_init function for OMAP4 and adds calls to
gpmc_init for existing OMAP4 boards: panda and sdp4430
Signed-off-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

OMAP4430 SDP is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU

This patch adds basic support for booting the board. It includes i2c and mmc
support. It assumes U-boot is loaded to SDRAM with the help of another small
bootloader (x-load) running from SRAM. U-boot currently relies on x-load for
clock, mux, and SDRAM initialization
Signed-off-by: NAneesh V <aneesh@ti.com>
Signed-off-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

This patch adds support for the Samsung Goni board (S5PC110 SoC)
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Patch by Rowel Atienza, 06 Apr 2005

- update ARM boards to use constants from mach-types.h