- 23 10月, 2015 16 次提交
-
-
由 Christophe Ricard 提交于
tpm_atmel_twi can fit perfectly to the new UCLASS_TPM class. Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com> Reviewed-by: NTom Rini <trini@konsulko.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Christophe Ricard 提交于
As there is no TCG specification or recommendation for i2c TPM 1.2, move tpm_tis_i2c driver to tpm_i2c_infineon. Other tpm vendors like Atmel or STMicroelectronics may have a different transport protocol for i2c. Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com> Reviewed-by: NTom Rini <trini@konsulko.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Mugunthan V N 提交于
Import various DT files for am57xx-beagle-x15 from Linux Kernel v4.2 Add config file for this board, enable DM, DM_GPIO, DM_SERIAL and DM_MMC. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
-
由 Mugunthan V N 提交于
Import various DT files for am437x-sk-evm from Linux Kernel v4.2 Add config file for this board, enable DM, DM_GPIO, DM_SERIAL and DM_MMC. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Mugunthan V N 提交于
Import various DT files for am4372, an43xx pinctrl and am437x-gp-evm from Linux Kernel v4.2 Add config file for this board, enable DM, DM_GPIO, DM_SERIAL and DM_MMC. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Mugunthan V N 提交于
enable mmc driver model for am335x gp_evm as omap_hsmmc supports driver model Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Mugunthan V N 提交于
enable mmc driver model for am335x bbb as omap_hsmmc supports driver model Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Mugunthan V N 提交于
Import various DT files for dra7-evm from Linux Kernel v4.2 Add config file for this board, enable DM and DM_GPIO Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Add config file for k2g Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NVitaly Andrianov <vitalya@ti.com>
-
由 Lokesh Vutla 提交于
Import k2e specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Import k2l specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Import k2hk specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Tom Rini 提交于
Tested on J6Eco EVM. Signed-off-by: NTom Rini <trini@konsulko.com> Tested-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Nishanth Menon 提交于
Introduce dummy devices for sandbox remoteproc device and enable it by default Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NNishanth Menon <nm@ti.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Mugunthan V N 提交于
enable ethernet driver model for am335x gp evm as cpsw supports driver model Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Mugunthan V N 提交于
enable ethernet driver model for am335x beagle bone black as cpsw supports driver model Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
- 21 10月, 2015 15 次提交
-
-
由 Simon Glass 提交于
Add support for the debug UART on link. This is useful for early debugging. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bin Meng 提交于
Now that we have added MRC cache on quark support codes, enable it on Intel Galileo board. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Now that we have added MRC cache for Intel FSP and BayTrail codes, enable it for all BayTrail boards (Bayley Bay and Minnow Max). Note it turns out that FSP for Intel Atom E6xx does not produce the HOB for NV storage, so we don't have such functionality on Intel Crown Bay board. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
mrccache implementation can be common for all boards. Move it from ivybridge cpu directory to the common lib directory. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Convert CONFIG_CMD_ELF to Kconfig and tidy up affected boards. Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Stefan Roese 提交于
This patch enables DM_USB on the Marvell AXP / A38x eval boards. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Luka Perkov <luka.perkov@sartura.hr>
-
由 Stefan Roese 提交于
This patch adds driver model support for some Marvell MVEBU SoC's. Including Armada XP and 38x. All 3 currently mainlined boards are converted. DM is now selected automatically for MVEBU platforms. With this DM support now available for MVEBU, hardcoding the base addresses and other information is not necessary any more. Probing should be done by using the values provided via the device tree now instead. For this the driver also need to be converted to DM. Patches for some of the drivers will follow. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Luka Perkov <luka.perkov@sartura.hr>
-
由 Maxime Ripard 提交于
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack and two connectors to plug additional boards on top of it. The DT is identical to the DT submitted to the upstream kernel. Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Hans de Goede 提交于
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features 1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver, stereo headphone jack and hdmi video output. The dts changes are identical to the dts files submitted upstream. A few notes on the use if dldo and aldo regulators. DLDO1 is used for Vdd for the ethernet phy, ALDO2 is used for AVdd for the ethernet phy. ALDO1 is used to power the sdio wifi module. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
ELDO3 is only necessary when using the lcd-panel, and not when using hdmi, the display code already takes care of enabling ELDO3 when necessary, so there is no need to permanently enable it in the deconfig. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V, make this the default. Note that this does not cause any functional changes since all sun8i board defconfig-s already contained: CONFIG_AXP_ALDO1_VOLT=3000 . Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
Change the axp223 dcdc2 / VDD-SYS default from 1.2V to 1.1V, 1.1V is the value recommended by Allwinner and is what most fex files specify. This has been tested on a number of A23/A33 tablets including on an A23 Ippo-q8h-v1.2 PCB tablet which has a fex file which specifies 1.2V (which is where our original 1.2V default comes from). Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
On boards with axp221/223 pmic-s we already allow configuring most voltages. Make the Kconfig options for these also apply to boards with axp152 / axp209 pmic-s and extend them to configure all voltages. The Kconfig defaults are chosen so that this commit does not introduce any functional changes. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER settings, removing them from CONFIG_SYS_EXTRA_OPTIONS. Note that sun5i boards can have either an AXP209 or an AXP152 pmic, the Kconfig default is AXP209, boards with an AXP152 must explicitly select this. Likewise boards without a pmic must explicitly select SUNXI_NO_PMIC in their defconfig. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
由 Hans de Goede 提交于
We now have generic q8_a?3_defconfig files for Q8 formfactor tablets with an A13 / A23 / A33 SoC, there is no need for these PCB variant specific defconfig-s and they only serve to confuse the user. Note that in case of the forfun_q88db_defconfig and TZX-Q8-713B7_defconfig for A13 based Q8 tablets there is not even a dts file for these in the upstream kernel, which is all the more reason to remove them. The generic q8_a?3_defconfig files have been tested on an Et_q8_v1_6, Ippo_q8h_v1_2_a33_1024x600, Ippo_q8h_v1_2 and TZX-Q8-713B7 tablet, and the forfun_q88db_defconfig is identical to q8_a13_tablet_defconfig. This leaves only the Ippo_q8h_v5 untested with the new generic defconfigs but there is no reason to assume that it will not work. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
- 20 10月, 2015 2 次提交
-
-
由 Stefan Roese 提交于
Introduce a mach-mvebu/Kconfig for all Armada based SoC's. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Tom Rini 提交于
Upon further review when populating README.scrapyard, inetspace_v2_cmc is a variant on netspace_v2 and not just an orphan config. This reverts commit 653600a7. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 19 10月, 2015 1 次提交
-
-
由 Tom Rini 提交于
Upon further review when populating README.scrapyard, d2net_v2 is a variant on net2big_v2 and not just an orphan config. To help in the future also add this to board/LaCie/net2big_v2/MAINTAINERS which needed a little consolidation anyhow. This reverts commit 1363740e. Cc: Simon Guinot <simon.guinot@sequanux.org> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 12 10月, 2015 4 次提交
-
-
由 Julius Werner 提交于
This patch adds support for LZ4-compressed FIT image contents. This algorithm has a slightly worse compression ration than LZO while being nearly twice as fast to decompress. When loading images from a fast storage medium this usually results in a boot time win. Sandbox-tested only since I don't have a U-Boot development system set up right now. The code was imported unchanged from coreboot where it's proven to work, though. I'm mostly interested in getting this recognized by mkImage for use in a downstream project. Signed-off-by: NJulius Werner <jwerner@chromium.org> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Stefan Roese 提交于
This platform has not gone into production. So lets remove it. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
-
由 Stefan Roese 提交于
This reverts commit 8fe11b89. I'll add support to lwmon5 in the next patch and will remove support for the broken lcd4_lwmon5 as well. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
-
由 Ryan Harkin 提交于
Create an additional FVP configuration to boot images pre-loaded into DRAM. Sometimes it's preferential to boot the model by loading the files directly into DRAM via model parameters, rather than using SemiHosting. An example of model parmaters that are used to pre-load the files into DRAM: --data cluster0.cpu0=Image@0x80080000 \ --data cluster0.cpu0=fvp-base-gicv2-psci.dtb@0x83000000 \ --data cluster0.cpu0=uInitrd@0x84000000 Signed-off-by: NRyan Harkin <ryan.harkin@linaro.org> Reviewed-by: NLinus Walleij <linus.walleij@linaro.org> [trini: Update board/armltd/vexpress64/Kconfig logic] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 10 10月, 2015 2 次提交
-
-
由 Siarhei Siamashka 提交于
The pcDuino1 board unconditionally provides 5V to USB host receptacles. The pcDuino2 board has a voltage regulator, controlled by the PD2 pin which is pulled-up by default (so that the USB power is also enabled by default). Not specifying pins for enabling USB power in the defconfig means that the PH3 and PH6 pins are driven high by default. The PH6 pin is available on the Arduino-compatible expansion header and touching it is not nice (this may be even dangerous, depending on what kind of role is assigned to this particular pin by various Arduino shields). This patch explicitly configures the USB VBUS pins to "", which means that no pins should be touched. The patch has been tested on a pcDuino2 board and USB still works. Signed-off-by: NSiarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 Siarhei Siamashka 提交于
Linksprite_pcDuino_defconfig is a generic config for pcDuino1 and pcDuino2 boards. The pcDuino2 board exists at least in two variants (with DDR3 chips from HYNIX or NANYA). At least one pcDuino2 board with HYNIX DDR3 fails the lima-memtester reliability test unless the DRAM clock speed is reduced to 360MHz. A detailed analysis report, generated by the a10-tpr3-scan tool with the explanations why the DRAM is failing at 408MHz, is available at: http://linux-sunxi.org/index.php?title=User:Ssvb/pcDuino2_with_HYNIX_DDR3_reliability_test&oldid=15152 http://web.archive.org/web/20151008190210/http://linux-sunxi.org/User:Ssvb/pcDuino2_with_HYNIX_DDR3_reliability_testSigned-off-by: NSiarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-