Convert T1040QDS and T1040RDB to use generic board code.
Signed-off-by: NVijay Rai <vijay.rai@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
  to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
  we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Add configs:
  o CONFIG_SYS_GENERIC_BOARD
  o CONFIG_DISPLAY_BOARDINFO
in C29XPCIE config header file to use U-boot generic
board code.
Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Add configs:
  o CONFIG_SYS_GENERIC_BOARD
  o CONFIG_DISPLAY_BOARDINFO
in P1023RDB config header file to use U-boot generic
board code.
Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Signed-off-by: NTang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

cppcheck reports:

[board/muas3001/muas3001.c:270]: (error) Uninitialized variable: psize

remove the CONFIG_SYS_RAMBOOT define to prevent this error report.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reported-by: NWolfgang Denk <wd@denx.de>
Reviewed-by: NYork Sun <yorksun@freescale.com>

This define is never set in our setup, so we can remove it safely. The
former code causes cppcheck to complain about:
[board/keymile/km82xx/km82xx.c:311]: (error) Uninitialized variable:
psize
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Use generic board architecture for p1010rdb, tested with NOR
boot on p1010rdb-pb.
Signed-off-by: NYing Zhang <b40530@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

The define CONFIG_FSL_SATA_V2 is missing, so SATA is not available
in U-boot.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Use generic board architecture for p1025-twr, tested with NOR
boot and NAND boot on p1025-twr.
Signed-off-by: NYing Zhang <b40530@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: NYing Zhang <b40530@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.

Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Enable interactive debugging by default. Remove DDR controller interleaving
because this SoC only has one controller. Use auto chip-select interleaving
to detect number of ranks.
Signed-off-by: NYork Sun <yorksun@freescale.com>
CC: Poonam Aggrwal <poonam.aggrwal@freescale.com>

Adjust timing for dual-rank UDIMM, verified on M3CQ-8GHS3C0E for speed of
1066, 1333, 1600, 1866MT/s. The 1866 timing is copied to 2133 timing in
case such DIMM comes available.

Also update single-rank 1866 timing. Enable interactive debugging as well.
Signed-off-by: NYork Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>

Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: NStefan Roese <sr@denx.de>

Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>

Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>

Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>

It is not used anywhere.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

For use together with the hdmi console.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>

Add simplefb support, note this depends on the kernel having support for
the clocks property which has recently been added to the simplefb devicetree
binding.
Signed-off-by: NLuc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as
 disussed on the devicetree list]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>.

Add a generic helper to fill and enable simplefb nodes.

The first user of this will be the sunxi display code.

lcd_dt_simplefb_configure_node is also a good candidate to be converted
to use this, but that requires someone to run some tests first, as
lcd_dt_simplefb_configure_node does not honor #address-cells and #size-cells,
but simply assumes 1 and 1 for both.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NSimon Glass <sjg@chromium.org>

This adds a fixed mode hdmi driver for the sunxi platform. The fixed
mode is a relatively safe 1024x768, more complete EDID handling is
currently not provided. Only HDMI is supported today.

This code is enabled when HPD detects an attached monitor.

Current config is such that 8MB is shaved off at the top of the RAM.
This avoids several memory handling issues, most significant is the fact
that on linux on ARM you are not allowed to remap known RAM as IO. A
clued in display driver will be able to recycle this reserved RAM in
future though.

cfbconsole was chosen as it provides the most important functionality: a
working u-boot console, allowing for the debugging of certain issues
without the need for a UART.
Signed-off-by: NLuc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Major cleanups and some small bugfixes]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAnatolij Gustschin <agust@denx.de>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

This patch enhances the boot of origen board by adding support to ext2, bootz, initrd, bootenv loading and boot script.
It still keeps the previous mmc load command if boot script fails.
Signed-off-by: NGuillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

SystemID information could be read through I2C1 from EEPROM
on LS1021ATWR board.

As LS1 is a little-endian processor, getting the version ID by
be32_to_cpu() is wrong. Fix it by using e.version directly.
This change will be compatible for both ARM and PowerPC.

As there is an errata that I2C1 could not work in SD boot,
reading EEPROM through I2C1 is disabled too in SD boot.
Signed-off-by: NAlison Wang <alison.wang@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Add define CONFIG_SYS_WRITE_SWAPPED_DATA.
For LS1021AQDS and LS1021QTWR nor flash write should swap the
bytes when handle unaligned tail bytes.

Because of the ending, if the date bus width is 16-bits and the
number of bytes is odd, we should swap the byte when write the
last one.
Signed-off-by: NYuan Yao <yao.yuan@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Enable USB EHCI Host on LS1021AQDS
Signed-off-by: NNikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Define USB configs for LS1021XA such as CONFIG_SYS_FSL_USB1_ADDR,
CONFIG_USB_MAX_CONTROLLER_COUNT
Signed-off-by: NNikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes
Signed-off-by: NNikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Implement sata stop command.
This introduces the __sata_stop() weak function, which mirrors
the weak __sata_initialize() function, giving users the option of
undoing the custom steps performed in overrides of sata_initialize().
Signed-off-by: NNikita Kiryanov <nikita@compulab.co.il>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>

Add reset_sata() to the sata driver interface and implement it
for dwc_ahsata. This function cleans up after sata_init(), and
therefore accepts a device number like sata_init() does.
A dummy implementation is provided for the rest of the drivers.
Signed-off-by: NNikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>

Add arch/arm/cpu/armv7/Kconfig with non-secure and virt options, this is a
preparation patch for adding an env variable to choose between secure /
non-secure boot on non-secure boot capable systems, specifically this
prepares for adding CONFIG_ARMV7_BOOT_SEC_DEFAULT as a proper Kconfig option.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

The sandbox/ext4/fat/generic fs commands do not gracefully deal with files
greater than 2GB. Negative values are returned in such cases.

To handle this, the fs functions have been modified to take an additional
parameter of type "* loff_t" which is then populated. The return value
of the fs functions are used only for error conditions.
Signed-off-by: NSuriyan Ramasami <suriyan.r@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>
[trini: Update board/gdsys/p1022/controlcenterd-id.c,
drivers/fpga/zynqpl.c for changes]
Signed-off-by: NTom Rini <trini@ti.com>

Change the internal sandbox functions to use loff_t for file offsets.
Signed-off-by: NSuriyan Ramasami <suriyan.r@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Change the internal EXT4 functions to use loff_t for offsets.
Signed-off-by: NSuriyan Ramasami <suriyan.r@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>
[trini: Update common/spl/spl_ext.c]
Signed-off-by: NTom Rini <trini@ti.com>

Change the internal FAT functions to use loff_t for offsets.
Signed-off-by: NSuriyan Ramasami <suriyan.r@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>
[trini: Fix fs/fat/fat.c for min3 updates]
Signed-off-by: NTom Rini <trini@ti.com>

Enable md5sum to obtain the MD5 of the read and written files to check
their contents for validity.
Use map_sysmem() to map buffer in a sandbox environment.
Signed-off-by: NSuriyan Ramasami <suriyan.r@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Since commit 0defddc8 (config: Add a default CONFIG_SYS_PROMPT),
each board header does not need to define CONFIG_SYS_PROMPT
as long as it uses the default prompt "=> ".
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

This macro can be overridden in source files (before including common.h)
and can be used to specify a prefix for debug and error messages. An
example of how to use this is shown below:

	#define pr_fmt(fmt) "foo: " fmt

	#include <common.h>

	...
	debug("bar");

The resulting message will read:

	foo: bar
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NSimon Glass <sjg@chromium.org>

When enumerating devices, honour the pci_skip_dev() function. This can
be used by PCI controller drivers to restrict which devices will be
probed.

This is required by the NVIDIA Tegra PCIe controller driver, which will
fail with a data abort exception if an access is attempted to a device
number larger than 0 outside of bus 0. pci_skip_dev() is therefore
implemented to prevent any such accesses.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NSimon Glass <sjg@chromium.org>