Skip to content

U
U-Boot.Mirror

OS / U-Boot.Mirror

通知 1
Star 0
Fork 0
U
U-Boot.Mirror

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 16 1月, 2012 9 次提交
  3. 14 1月, 2012 21 次提交
  5. 12 1月, 2012 10 次提交
    • P
      sbc8548: Fix up local bus init to be frequency aware · e2b363ff
      由 Paul Gortmaker 提交于 
      The code here was copied from the mpc8548cds support, and it
wasn't using the CONFIG_SYS_LBC_LCRR define, and was just
unconditionally setting the LCRR_EADC bit.  Snooping with a
hardware debugger also showed we had LCRR_DBYP set, since we were
setting it based on a read of an uninitialized lcrr read via
clkdiv.  Borrow from the code in the tqm85xx.c support to add
LBC frequency aware masking of these bits.

This change will correct reliability issues associated with trying
to use the 128MB of LBC 100MHz SDRAM on this board.  Thanks to
Keith Savage for assistance in diagnosing the root cause of this.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      e2b363ff
    • P
      sbc8548: enable support for hardware SPD errata workaround · 3e3262bd
      由 Paul Gortmaker 提交于 
      Existing boards by default have an issue where the LBC SDRAM
SPD EEPROM and the DDR2 SDRAM SPD EEPROM both land at 0x51.

After the hardware modification listed in the README is made,
then the DDR2 SPD EEPROM appears at 0x53.  So this implements
a board specific get_spd() by taking advantage of the existing
weak linkage, that 1st tries reading at 0x53 and then if that
fails, it falls back to the old 0x51.

Since the old dependency issue of "SPD implies no LBC SDRAM"
gets removed with the hardware errata fix, remove that restriction
in the code, so both LBC SDRAM and SPD can be selected.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      3e3262bd
    • P
      sbc8548: relocate fixed ddr init code to ddr.c file · 2a6b3b74
      由 Paul Gortmaker 提交于 
      Nothing to see here, just a relocation of the fixed ddr init
sequence to live in the actual ddr.c file itself.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      2a6b3b74
    • P
      sbc8548: Make enabling SPD RAM configuration work · 7e44f2b7
      由 Paul Gortmaker 提交于 
      Previously, SPD configuration of RAM was non functional on
this board.  Now that the root cause is known (an i2c address
conflict), there is a simple end-user workaround - remove the
old slower local bus 128MB module and then SPD detection on the
main DDR2 memory module works fine.

We make the enablement of the LBC SDRAM support conditional on
being not SPD enabled.  We can revisit this dependency as the
hardware workaround becomes available.

Turning off LBC SDRAM support revealed a couple implict dependencies
in the tlb/law code that always expected an LBC SDRAM address.

This has been tested with the default 256MB module, a 512MB
a 1GB and a 2GB, of varying speeds, and the SPD autoconfiguration
worked fine in all cases.

The default configuration remains to go with the hard coded
DDR config, so the default build will continue to work on boards
where people don't bother to read the docs.  But the advantage
of going to the SPD config is that even the small default module
gets configured for CL3 instead of CL4.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      7e44f2b7
    • P
      sbc8548: Fix LBC SDRAM initialization settings · 5f4c6f0d
      由 Paul Gortmaker 提交于 
      These were cloned from the mpc8548cds platform which has
a different memory layout (1/2 the size).  Set the values
by comparing to the register file for the board used during
JTAG init sequence:

	LSDMR1		0x2863B727	/* PCHALL */
	LSDMR2		0x0863B727	/* NORMAL */
	LSDMR3		0x1863B727	/* MRW    */
	LSDMR4		0x4063B727	/* RFEN   */

This differs from what was there already in that the RFEN is
not bundled in all four steps implicitly, but issued once
as the final step.

The other difference seen when comparing vs. the register file init,
is that since the memory is split across /CS3 and /CS4, the dummy
writes need to go to 0xf000_0000 _and_ to 0xf400_0000.

We also rewrite the final LBC SDRAM inits as macros, as there is
no real need for them to be a local variable that is modified
on the fly at runtime.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      5f4c6f0d
    • P
      sbc8548: enable ability to boot from alternate flash · f0aec4ea
      由 Paul Gortmaker 提交于 
      This board has an 8MB soldered on flash, and a 64MB SODIMM
flash module.  Normally the board boots from the 8MB flash,
but the hardware can be configured for booting from the 64MB
flash as well by swapping CS0 and CS6.  This can be handy
for recovery purposes, or for supporting u-boot and VxBoot
at the same time.

To support this in u-boot, we need to have different BR0/OR0
and BR6/OR6 settings in place for when the board is configured
in this way, and a different TEXT_BASE needs to be used due
to the larger sector size of the 64MB flash module.

We introduce the suffix _8M and _64M for the BR0/BR6 and the
OR0/OR6 values so it is clear which is being used to map what
specific device.

The larger sector size (512k) of the alternate flash needs
a larger malloc pool, otherwise you'll get failures when
running saveenv, so bump it up accordingly.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      f0aec4ea
    • P
      sbc8548: relocate 64MB user flash to sane boundary · 3fd673cf
      由 Paul Gortmaker 提交于 
      The current situation has the 64MB user flash at an awkward
alignment; shifted back from 0xfc00_0000 by 8M, to leave an 8MB hole
for the soldered on boot flash @ EOM.  But to switch to optionally
supporting booting off the 64MB flash, the 64MB will then be mapped
at the sane address of 0xfc00_0000.

This leads to awkward things when programming the 64MB flash prior
to transitioning to it -- i.e. even though the chip spans from
0xfb80_0000 to 0xff7f_ffff, you would have to program a u-boot image
into the two sectors from 0xfbf0_0000 --> 0xfbff_ffff so that it was
in the right place when JP12/SW2.8 were switched to make the 64MB on
/CS0. (i.e. the chip is only looking at the bits in mask 0x3ff_ffff)

We also have to have three TLB entries responsible for dealing with
mapping the 64MB flash due to this 8MB of misalignment.

In the end, there is address space from 0xec00_0000 to 0xefff_ffff
where we can map it, and then the transition from booting from one
config to the other will be a simple 0xec --> 0xfc mapping.  Plus we
can toss out a TLB entry.

Note that TLB0 is kept at 64MB and not shrunk down to the 8MB boot
flash; this means we won't have to change it when the alternate
config uses the full 64MB for booting, in TLB0.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      3fd673cf
    • P
      Revert "SBC8548: fix address mask to allow 64M flash" · af35be6a
      由 Paul Gortmaker 提交于 
      This reverts commit ccf1ad53.

The commit "SBC8548: fix address mask to allow 64M flash"
essentially made this change:

  * OR6:
- *    Addr Mask = 64M = OR6[0:16] = 1111 1100 0000 0000 0
+ *    Addr Mask = 64M = OR6[0:16] = 1111 1000 0000 0000 0

But this makes no sense, as section 13.3.1.2.1 in the
MPC8548ERM v2 clearly indicates the masks:

	1111_1111_1000_0000_0	8 Mbytes
	1111_1100_0000_0000_0	64 Mbytes
	1111_1000_0000_0000_0	128 Mbytes

So the original value was correct, and the commit was invalid,
causing a 128MB mapping for a 64MB flash device.  The problem
rears its head when trying to configure u-boot to have access
to both flash, since the default memory map is:

	FB80_0000 – FF7F_FFFF 32-bits 64MB FLASH SODIMM
	FF80_0000 – FFFF_FFFF 8-bits 8MB FLASH

By extending the mapping of the 64MB flash to 128MB, it now
conflicts with the normal 8MB boot flash, causing issues.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      af35be6a
    • P
      MPC85xxCDS: Fix missing LCRR_DBYP bits for 66-133MHz LBC · 1667013d
      由 Paul Gortmaker 提交于 
      These boards were meaning to deploy this value:

  #define LCRR_DBYP        0x80000000

but were missing a zero, and hence toggling a bit that
lands in an area marked as reserved in the 8548 reference
manual.

According to the documentation, LCRR_DBYP should be used as:

   PLL bypass. This bit should be set when using low bus
   clock frequencies if the PLL is unable to lock.  When in
   PLL bypass mode, incoming data is captured in the middle
   of the bus clock cycle.  It is recommended that PLL bypass
   mode be used at frequencies of 83 MHz or less.

So the impact would most likely be undefined behaviour for
LBC peripherals on boards that were running below 83MHz LBC.
Looking at the actual u-boot code, the missing DBYP bit was
meant to be deployed as follows:

      Between 66 and 133, the DLL is enabled with an
      override workaround.

In the future, we'll convert all boards to use the symbolic
DBYP constant to avoid these "count the zeros" problems, but
for now, just fix the impacted boards.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      1667013d
    • K
      eXMeritus HWW-1U-1A: Add support for the AT24C128N I2C EEPROM · 0ecb5513
      由 Kyle Moffett 提交于 
      This EEPROM is hardware-write-protected and used to persist key
information such as the serial number and MAC addresses even if the
primary environment sector in NOR FLASH is overwritten.

During manufacturing, the environment is initialized from Linux and then
the key parameters copied to the EEPROM via U-Boot:

  env export -c -s 0x2000 $loadaddr serial# macaddr mac1addr mac2addr
  eeprom write $loadaddr 0x0000 0x2000

The chip is then locked via hardware for delivery.

When doing a field U-Boot upgrade, the environment is erased and reset
to the defaults to avoid problems with "hwconfig" changes, etc.  After
loading the new U-Boot image, the hardware data is reloaded:

  i2c dev 0
  eeprom read $loadaddr 0x0000 0x2000
  env import -c $loadaddr 0x2000
  saveenv

The first three commands are saved in the "restore_eeprom" variable for
user convenience.  (EG: "run restore_eeprom && saveenv")
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      0ecb5513