- 12 9月, 2003 14 次提交
-
-
由 stroese 提交于
-
由 stroese 提交于
-
由 stroese 提交于
-
由 stroese 提交于
-
由 stroese 提交于
-
由 stroese 提交于
-
由 stroese 提交于
-
由 stroese 提交于
-
由 stroese 提交于
-
由 stroese 提交于
-
由 stroese 提交于
-
由 stroese 提交于
-
由 wdenk 提交于
add burn-in tests for TRAB board * Enable instruction cache on MPC5200 board
-
由 wdenk 提交于
- allow for longer timeouts for USB mass storage devices * Patch by Denis Peter, 11 Sep 2003: - fix USB data pointer assignment for bulk only transfer. - prevent to display erased directories in FAT filesystem. * Change output format for NAND flash - make it look like for other memory, too
-
- 11 9月, 2003 2 次提交
-
-
由 wdenk 提交于
add FAT support for IDE, SCSI and USB * Patches by Gleb Natapov, 2 Sep 2003: - cleanup of POST code for unsupported architectures - MPC824x locks way0 of data cache for use as initial RAM; this patch unlocks it after relocation to RAM and invalidates the locked entries. * Patch by Gleb Natapov, 30 Aug 2003: new I2C driver for mpc107 bridge. Now works from flash. * Patch by Dave Ellis, 11 Aug 2003: - JFFS2: fix typo in common/cmd_jffs2.c - JFFS2: fix CFG_JFFS2_SORT_FRAGMENTS option - JFFS2: remove node version 0 warning - JFFS2: accept JFFS2 PADDING nodes - SXNI855T: add AM29LV800 support - SXNI855T: move environment from EEPROM to flash - SXNI855T: boot from JFFS2 in NOR or NAND flash * Patch by Bill Hargen, 11 Aug 2003: fixes for I2C on MPC8240 - fix i2c_write routine - fix iprobe command - eliminates use of global variables, plus dead code, cleanup.
-
由 wdenk 提交于
(tested with USB memory sticks only) * Avoid flicker on TRAB's VFD
-
- 06 9月, 2003 1 次提交
-
-
由 wdenk 提交于
* Add PCI support for SL8245 board * Support IceCube board configurations with 1 x AMD AM29LV065 (8 MB) or 1 x AM29LV652 (two LV065 in one chip = 16 MB); Run IPB at 133 Mhz; adjust the MII clock frequency accordingly * Set BRG_CLK on PM825/826 to 64MHz (VCO_OUT / 4, instead of 16 MHz) to allow for more accurate baudrate settings (error now 0.7% at 115 kbps, instead of 3.5% before) * Patch by Andreas Mohr, 4 Sep 2003: Fix a lot of spelling errors
-
- 03 9月, 2003 3 次提交
- 01 9月, 2003 1 次提交
-
-
由 wdenk 提交于
According to the MPC8260 User's Manual, PCI_MODE signal should be reflected in SCCR register, and local bus pins configuration is taken from HRCW and appears in SIUMCR. For some reason it does not work this way, so the only possibility to detect if the board is configured in PCI mode is to check the BCSR. This patch sets SCCR and SIUMCR according to the BCSR.
-
- 30 8月, 2003 3 次提交
- 29 8月, 2003 1 次提交
-
-
由 wdenk 提交于
(because of better response to iprobe command); fix problem with "reset" command
-
- 28 8月, 2003 3 次提交
- 18 8月, 2003 1 次提交
-
-
由 wdenk 提交于
allow selection of clock frequency as "make" target * Implement memory autosizing code for IceCube boards * Configure network port on INCA-IP for autonegotiation * Fix overflow problem in network timeout code * Patch by Richard Woodruff, 8 Aug 2003: Allow crc32 to be used at address 0x000 (crc32_no_comp, too).
-
- 08 8月, 2003 1 次提交
-
-
由 wdenk 提交于
disable clocks_in_mhz, enable boot count limit
-
- 07 8月, 2003 4 次提交
- 06 8月, 2003 2 次提交
- 01 8月, 2003 1 次提交
-
-
由 wdenk 提交于
-
- 27 7月, 2003 1 次提交
-
-
由 wdenk 提交于
Add support for LynuxWorks Kernel Downloadable Images (KDIs). Both LynxOS and BlueCat linux KDIs are supported. * Patch by Richard Woodruff, 25 Jul 2003: use more reliable reset for OMAP/925T * Patch by Nye Liu, 25 Jul 2003: fix typo in mpc8xx.h * Patch by Richard Woodruff, 24 Jul 2003: Fixes for cmd_nand.c: - Fixed null dereferece which could result in incorrect ECC values. - Added support for devices with no Ready/Busy signal hooked up. - Added OMAP1510 read/write protect handling. - Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock for non-JFFS2. - Switched default ECC to be JFFS2.
-
- 26 7月, 2003 1 次提交
-
-
由 wdenk 提交于
* Provide consistent interface to standalone applications to access the 'global_data' structure Provide a doc/README.standalone more useful to users/developers. * Make IceCube MGT5100 FEC driver work
-
- 25 7月, 2003 1 次提交
-
-
由 wdenk 提交于
applications: instead of using (PPC-specific) system calls we now use a jump table; please see doc/README.standalone for details * Patch by Dave Westwood, 24 Jul 2003: added support for Unity OS (a proprietary OS)
-