fdt_find_and_setprop() is used by several 4xx boards and it's
missing in the appropriate header. This patch eliminates a
warning when building U-Boot for such boards.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: NStefan Roese <sr@denx.de>

Now that there are no board-specific versions of
"denali_core_search_data_eye()", the weak binding on the common version
can be removed.
Signed-off-by: NLarry Johnson <lrj@acm.org>

Signed-off-by: NStefan Roese <sr@denx.de>

On Katmai the complete auto-calibration somehow doesn't seem to
produce the best results, meaning optimal values for RQFD/RFFD.
This was discovered by GDA using a high bandwidth scope,
analyzing the DDR2 signals. GDA provided a fixed value for RQFD,
so now on Katmai "only" RFFD is auto-calibrated.

This patch also adds RDCC calibration as mentioned on page 7 of
the AMCC PowerPC440SP/SPe DDR2 application note:
"DDR1/DDR2 Initialization Sequence and Dynamic Tuning"
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

The Sequoia NAND booting target now uses the recently extracted
cpu/ppc4xx/denali_data_eye.c file too.
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NLarry Johnson <lrj@acm.org>

Note: this patch changes the configuration of some GPIO registers:

   Register      Old Value   New Value
---------------  ----------  ----------
DCR GPIO0_TCR    0x0000000F  0x0000F0CF
DCR GPIO0_TSRH   0x55005000  0x00000000
DCR GPIO1_TCR    0xC2000000  0xE2000000
DCR GPIO1_TSRL   0x0C000000  0x00200000
DCR GPIO1_ISR2L  0x00050000  0x00110000
Signed-off-by: NLarry Johnson <lrj@acm.org>

This patch makes two additions to GPIO support:

First, it adds function gpio_read_in_bit() to read the a bit from the
GPIO Input Register (GPIOx_IR) in the same way that function
gpio_read_out_bit() reads a bit from the GPIO Output Register
(GPIOx_OR).

Second, it modifies function gpio_set_chip_configuration() to provide
an additional option for configuring the GPIO from the
"CFG_4xx_GPIO_TABLE".

According to the 440EPx User's Manual, when an alternate output is used,
the three-state control is configured in one of two ways, depending on
the particular output.  The first option is to select the corresponding
alternate three-state control in the GPIOx_TRSH/L registers.  The second
option is to select the GPIO Three-State Control Register (GPIOx_TCR) in
the GPIOx_TRSH/L registers, and set the corresponding bit in the
GPIOx_TCR register to enable the output.  For example, the Manual
specifies configuring the GPIO00 Alternate 1 Signal (PreAddr07) to use
the alternate three-state control (first option), and specifies
configuring the GPIO32 Alternate 1 Signal (USB2OM0) with the output
enabled in the GPIOx_TCR register (second option).

Currently, gpio_set_chip_configuration() configures all alternate signal
outputs to use the first option.  This patch allow the second option to
be selected by setting the "out_val" element in the table entry to
"GPIO_OUT_1".  The first option is used when the "out_val" element is
set to "GPIO_OUT_0".  Because "out_val" is not currently used when an
alternate signal is selected, and because all current GPIO tables set
"out_val" to "GPIO_OUT_0" for all alternate signals, this patch should
not change any existing configurations.
Signed-off-by: NLarry Johnson <lrj@acm.org>

These definitions are now in "include/ppc440.h".
Signed-off-by: NLarry Johnson <lrj@acm.org>

This patch also modifies the functionality of the code so that the data-eye
search is now done with with the cache disabled.
Signed-off-by: NLarry Johnson <lrj@acm.org>

These definitions are now in "include/ppc440.h".
Signed-off-by: NLarry Johnson <lrj@acm.org>

Signed-off-by: NLarry Johnson <lrj@acm.org>

When CONFIG_NET_DO_NOT_TRY_ANOTHER is defined U-Boot's
networking stack does not automatically switch to
another interface. This patch does not touch the default
behavior.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: NBen Warren <biggerbadderben@gmail.com>

This patch modifies the return code handling in the eth_init()
function, to be compatible with the handling of the return codes in
the other network stack files. It now returns a 0 on Success and -1 on
error.
Signed-off-by: NUpakul Barkakaty <upakul.barkakaty@conexant.com>
Signed-off-by: NBen Warren <biggerbadderben@gmail.com>

Assigning the output of simple_strtoul(CB:A9:87:65:43:21) to `char', we are
warned as below:

  U-Boot 1.2.0 (Aug 30 2007 - 08:27:37)

  DRAM:  256 MB
  Flash: 32 MB
  In:    serial
  Out:   serial
  Err:   serial
  Net:   NEC-Candy
  Warning: NEC-Candy MAC addresses don't match:
  Address in SROM is         00:00:4C:80:92:A2
  Address in environment is  FFFFFFCB:FFFFFFA9:FFFFFF87:65:43:21

This patch changes env_enetaddr type from `char' to `unsigned char'.

Cc: Masaki Ishikawa <ishikawa-masaki@cnt.mxe.nes.nec.co.jp>
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NBen Warren <biggerbadderben@gmail.com>

The purpose of this routine is receiving a single network frame, outside of
U-Boot's NetLoop(). Exporting it to standalone programs that run on top of
U-Boot will let them utilise networking facilities. For sending a raw frame
the already existing eth_send() can be used.

The direct consumer of this routine is the newly introduced API layer for
external applications (enabled with CONFIG_API).
Signed-off-by: NRafal Jaworowski <raj@semihalf.com>
Signed-off-by: NPiotr Kruszynski <ppk@semihalf.com>
Signed-off-by: NBen Warren <biggerbadderben@gmail.com>

Include config.h earlier in the set of #includes
so as to avoid a incidental and duplicate definition
of CFG_CACHELINE_SIZE.

Signed-off-by: Jon Loeliger

Doing so prevents it from being individually set
and useful in other files.
Signed-off-by: NJon Loeliger <jdl@freescale.com>

Assumes the presence of the aliases node in the DTS to
locate the ethernet, pci and serial nodes for fixups.

Use consistent fdtaddr and fdtfile in environment variables.
Signed-off-by: NJon Loeliger <jdl@freescale.com>

This bug was detected on the LWMON5 target which has 2 Intel 16bit wide
flash chips connected to a 32bit wide port.
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

The bash builtin versions of the "test" (resp. "[") command allow
using "==" for string comparisons, but POSIX compatible implemen-
tations (like /usr/bin/test) insist on using "=" only. On such systems
you will see:

	$ /usr/bin/test a == a && echo OK
	/usr/bin/test: ==: binary operator expected

This patch fixes Makefiles and scripts to use POSIX style.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Conflicts:

	cpu/ppc4xx/fdt.c
	include/configs/kilauea.h
	include/configs/sequoia.h
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

This patch adds some BSP commands and FPGA booting support
for esd's PMC440 boards.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

This patch adds the first files for the new esd PMC440 boards.
The next two patches will complete the PMC440 board support.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

- add EEPROM write protection for esd PLU405 boards.
- initialize NAND GPIOs
- use correct io accessors
- cleanup
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

This patch fixes esd's LCD dectection code to work correctly with
newer gcc versions.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

- add EEPROM write protection
- initialize NAND GPIOs
- use correct io accessors
- slow down I2C clock to 100kHz
- enable ext. I2C bus
- cleanup
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>