- 21 10月, 2007 3 次提交
-
-
由 Shinya Kuribayashi 提交于
Now we load $gp with _GLOBAL_OFFSET_TABLE_, but this is incorrect use. As a general principle, we should use _gp for $gp. Thanks to linker script's help we fortunately have _gp which equals to _GLOBAL_OFFSET_TABLE_. But once _gp gets out of alignment, we will not be able to access to GOT entires, global variables and procedure entry points. The right thing to do is to use _gp. This patch also introduce a new symbol `.gpword _GLOBAL_OFFSET_TABLE_' which holds the offset from _gp. When updating GOT entries, we use this offset and _gp to calculate the final _GLOBAL_OFFSET_TABLE_. This patch is originally submitted by Vlad Lungu <vlad@comsys.ro>, then I made some change to leave over num_got_entries. Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com> Cc: Vlad Lungu <vlad@comsys.ro>
-
由 Shinya Kuribayashi 提交于
Ensure that __got_start points to top of the `.got', and __got_end points to bottom as well, so that we never fail to count num_got_entries. Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
-
由 Shinya Kuribayashi 提交于
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
-
- 19 10月, 2007 2 次提交
-
-
由 Detlev Zundel 提交于
Signed-off-by: NDetlev Zundel <dzu@denx.de>
-
-
- 18 10月, 2007 4 次提交
-
-
由 Tony Li 提交于
Add MPC8360EMDS_ATM_config and MPC832XEMDS_ATM_config into Makfile and MAKEALL Signed-off-by: NTony Li <tony.li@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Tony Li 提交于
Correct to val8 from val. Signed-off-by: NTony Li <tony.li@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
- 16 10月, 2007 4 次提交
-
-
-
由 Jon Loeliger 提交于
As a direct correlation exists between DDR DIMM slots and SPD EEPROM addresses used to configure them, use the individually defined SPD_EEPROM_ADDRESS* values to determine if a DDR DIMM slot should have its SPD configuration read or not. Effectively, this now allows for 1 or 2 DIMM slots per memory controller. Signed-off-by: NJon Loeliger <jdl@freescale.com>
-
由 Wolfgang Denk 提交于
-
-
- 15 10月, 2007 4 次提交
-
-
-
由 Rodolfo Giometti 提交于
Some USB keys need to be switched off before loading the kernel otherwise they can remain in an undefined status which prevents them to be correctly recognized by the kernel. Signed-off-by: NRodolfo Giometti <giometti@linux.it>
-
由 Stefan Roese 提交于
The I2C bootstrap values that can be setup via the "bootstrap" command, were setup incorrect regarding the generation of the internal sync PCI clock. The values for PLB clock == 133MHz were slighly incorrect and the values for PLB clock == 166MHz were totally incorrect. This could lead to a hangup upon booting while PCI configuration scan. This patch fixes this issue and configures valid PCI divisor values for the sync PCI clock, with respect to the provided external async PCI frequency. Here the values of the formula in the chapter 14.2 "PCI clocking" from the 440EPx users manual: AsyncPCICLK - 1MHz <= SyncPCIClk <= (2 * AsyncPCIClk) - 1MHz 33MHz async PCI frequency: PLB = 133: => 32 <= 44.3 <= 65 (div = 3) PLB = 166: => 32 <= 55.3 <= 65 (div = 3) 66MHz async PCI frequency: PLB = 133: => 65 <= 66.5 <= 132 (div = 2) PLB = 166: => 65 <= 83 <= 132 (div = 2) Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
The BCSR status bit for the 66MHz PCI operation was correctly addressed (MSB/LSB problem). Now the correct currently setup PCI frequency is displayed upon bootup. This patch also fixes this problem on Rainier & Yellowstone, since these boards use the same souce code as Sequoia & Yosemite do. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 14 10月, 2007 12 次提交
-
-
由 Michal Simek 提交于
and remove code violation
-
-
由 Michal Simek 提交于
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Wolfgang Denk 提交于
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: NWolfgang Denk <wd@denx.de>
-
-
-
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
-
- 12 10月, 2007 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 10 10月, 2007 3 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
- 09 10月, 2007 1 次提交
-
-
由 Grzegorz Bernacki 提交于
Signed-off-by: NGrzegorz Bernacki <gjb@semihalf.com>
-
- 07 10月, 2007 1 次提交
-
-
由 Haavard Skinnemoen 提交于
The ATSTK1000-specific flash driver intializes bi_flashstart, bi_flashsize and bi_flashoffset, but other flash drivers, like the CFI driver, don't. Initialize these in board_init_r instead so that things will still be set up correctly when we switch to the CFI driver. Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
-
- 05 10月, 2007 2 次提交
-
-
由 Marian Balakowicz 提交于
Signed-off-by: NMarian Balakowicz <m8@semihalf.com>
-
由 Bartlomiej Sieka 提交于
Signed-off-by: NBartlomiej Sieka <tur@semihalf.com>
-
- 04 10月, 2007 1 次提交
-
-
- 03 10月, 2007 2 次提交
-
-
由 Haavard Skinnemoen 提交于
CFG_MEMTEST_START uses weird magic involving gd, which fails to compile. Use hardcoded values instead (we actually know how much RAM we have on board.) Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
-
由 Haavard Skinnemoen 提交于
-