The existing 'led' command does not support driver model. Rename it to
indicate that it is legacy code.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NZiping Chen <techping.chan@gmail.com>

Allow LEDs to be blinked if the driver supports it. Enable this for
sandbox so that the tests run.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NZiping Chen <techping.chan@gmail.com>

Add support for toggling an LED into the uclass interface. This can be
efficiently implemented by the driver.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NZiping Chen <techping.chan@gmail.com>

It is useful to be able to read the LED as well as write it. Add this to
the uclass and update the GPIO driver.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NZiping Chen <techping.chan@gmail.com>

At present this is very simple, supporting only on and off. We want to
also support toggling and blinking. As a first step, change the name of
the main method and use an enum to indicate the state.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NZiping Chen <techping.chan@gmail.com>

These structures are normally named with 'uc' instead of 'uclass'. Change
this one for consistency.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NZiping Chen <techping.chan@gmail.com>

There should be a blank line between each option. Add one before LED_GPIO.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NZiping Chen <techping.chan@gmail.com>

Add some LEDs to the standard sandbox device tree.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NZiping Chen <techping.chan@gmail.com>

With DM_SCSI enabled, blk_create_devicef() is called with blkz = 0, leading
to a divide-by-0 exception.
scsi_detect_dev() can be used to get the required parameters (block size
and number of blocks) from the drive before calling blk_create_devicef().
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

We might want to get information about the scsi device without initializing the partition.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This is a cosmetic change. target and LUN have kind of the same role in
this function. One of them was passed as a parameter and the other was
embedded in a structure. For consistency, pass both of them as parameters.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

When CONFIG_DM_SCSI is defined, the SATA initialization will be implemented
in the scsi-uclass driver.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

All the clocks which has to be enabled has to be done in
enable_basic_clocks(), so moving enable sata clock to common
clocks enable function.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

When writing out some of our results we may now have UTF-8 characters
in there as well.  Translate these to latin-1 and ignore any errors (as
this is for diagnostic and given the githash anything else can be
reconstructed by the user.
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Rini <trini@konsulko.com>

This fixes a regression caused by

commit 07b2b78c
    dm: usb: Convert USB storage to use driver-model for block devs

which caused part_init to be called when it was not previously.
Without this patch, the following happens when a USB sd card reader is used.

=> usb start
starting USB...
USB0:   Port not available.
USB1:   USB EHCI 1.00
scanning bus 1 for devices... 3 USB Device(s) found
       scanning usb for storage devices... Device NOT ready
   Request Sense returned 02 3A 00
 ### ERROR ### Please RESET the board ###

This happens because dev_desc->blksz is 0.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

We should invalidate the dcache before starting the DMA. In case there are
any dirty lines from the DMA buffer in the cache, subsequent cache-line
replacements may corrupt the buffer in memory while the DMA is still going on.
Cache-line replacement can happen if the CPU tries to bring some other memory
locations into the cache while the DMA is going on.
Signed-off-by: NEddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: NStefan Brüns <stefan.bruens@rwth-aachen.de>

Merely using dma_alloc_coherent does not ensure that there is no stale
data left in the caches for the allocated DMA buffer (i.e. that the
affected cacheline may still be dirty).

The original code was doing the following (on AArch64, which
translates a 'flush' into a 'clean + invalidate'):
  # during initialisation:
      1. allocate buffers via memalign
      	 => buffers may still be modified (cached, dirty)
  # during interrupt processing
      2. clean + invalidate buffers
      	 => may commit stale data from a modified cacheline
      3. read from buffers

This could lead to garbage info being written to buffers before
reading them during even-processing.

To make the event processing more robust, we use the following sequence
for the cache-maintenance:
  # during initialisation:
      1. allocate buffers via memalign
      2. clean + invalidate buffers
      	 (we only need the 'invalidate' part, but dwc3_flush_cache()
	  always performs a 'clean + invalidate')
  # during interrupt processing
      3. read the buffers
      	 (we know these lines are not cached, due to the previous
	  invalidation and no other code touching them in-between)
      4. clean + invalidate buffers
      	 => writes back any modification we may have made during event
	    processing and ensures that the lines are not in the cache
	    the next time we enter interrupt processing

Note that with the original sequence, we observe reproducible
(depending on the cache state: i.e. running dhcp/usb start before will
upset caches to get us around this) issues in the event processing (a
fatal synchronous abort in dwc3_gadget_uboot_handle_interrupt on the
first time interrupt handling is invoked) when running USB mass
storage emulation on our RK3399-Q7 with data-caches on.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

The dwc3_flush_cache() call was declared and used inconsistently:
 * The declaration assumed 'int' for addresses (a potential issue
   when running in a LP64 memory model).
 * The invocation cast the address to 'long'.

This change ensures that both the declaration and usage of this
function consistently uses 'uintptr_t' for correct behaviour even
when the allocated buffers (to be flushed) reside outside of the
lower 32bits of memory.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Both these numbers are calculated in runtime and dynamically assigned
to the device descriptor during bind().
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

We don't want to claim that we support a serial number string and
later return nothing. Because of that, if g_dnl_serial is an empty
string, let's skip setting iSerialNumber to a valid number.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

A USB String descriptor can be up to 255 characters long and it's not
NULL terminated according to the USB spec. This means our
MAX_STRING_SERIAL should be 256 (to cope with NULL terminator).
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Some board do not use the dwc2 internal VBUS_DRV signal, but
use a gpio pin to enable the 5.0V VBUS power, add interface to
enable the power in dwc2 driver.
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Signed-off-by: NSimon Glass <sjg@chromium.org>

This removes the default environment from the sr1500 header
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

This board has no upstream devicetree in the kernel source,
so set to socfpga_cyclone5_sr1500.dtb.
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>

--
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE
 - set devicetree name to match socfpga_{fpga model}_{board model}.dts
   pattern

This removes the default environment from the socrates headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>

--
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE

This removes the default environment from the SoCKit headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>

--
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE

This removes the default environment from the de1 headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

This board does not have a devicetree in the upstream kernel
source so set devicetree to socfpga_cyclone5_de1_soc.dtb.
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>

--
Changes in V2:
 - Remove unneeded CONFIG_BOOTFILE
 - set devicetree name to match socfpga_{fpga model}_{board model}.dts
   pattern

This removes the default environment from the C5 SoCDK headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

In addition to the above, add support to boot from the custom
a2 type partition.

Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>

--
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE

This removes the default environment from the A5 socdk headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

Add support to boot from the custom a2 type partition.

Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>

--
Changes in v3:
 - Fix small typo in defconfig, missing "C"
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE
 - Fix dtb name

a5config test
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>

This removes the default environment from the de0 headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

In addition to the above, add support to boot from the custom
a2 type partition
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>

--
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE

This adds a common environment and support for distro boot
in the common socfpga header.
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>

--
Changes in v5:
 - Per Frank, to support OpenSuse the ENV must be after the GPT
Changes in v4:
 - Move env back to being right after the MBR
Changes in v3:
 - fix spacing between asterix
 - remove verify=n as a default setting

Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE and fdt_addr
 - cleanup spacing in MMC env size

common
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>

Convert Altera DDR SDRAM driver to use Kconfig method.
Enable ALTERA_SDRAM by default if it is on Gen5 target.
Arria 10 will have different driver.
Signed-off-by: NTien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>

Add compatible strings for Intel Arria 10 SoCFPGA device.
Signed-off-by: NTien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>

Disable the OC test on MCVEVK as the old PHY version does not provide
this information. This fixes the USB OTG operation.
Signed-off-by: NMarek Vasut <marex@denx.de>

Add default DFU altinfo for eMMC.
Signed-off-by: NMarek Vasut <marex@denx.de>

There is no point in having such gargantuan buffer, it only requires
huge malloc area. Reduce the DFU buffer size.
Signed-off-by: NMarek Vasut <marex@denx.de>

The board is now manufactured by Aries Embedded GmbH , rename it.
Signed-off-by: NMarek Vasut <marex@denx.de>

Commit ce62e57f ("ARM: boot0 hook: remove macro, include whole
header file") miss out cleaning macro in this header file, and this
has broken implementation of a boot header capability in socfpga
SPL. Remove the macro in this file, and recovering it back
to proper functioning.

Fixes: ce62e57f ("ARM: boot0 hook: remove macro, include whole
header file")
Signed-off-by: NChee, Tien Fong <tien.fong.chee@intel.com>