The lines COL (collision detect) and CRS (carrier sense) needs to be connected
and muxed to the CPSW MAC for a proper function in half-duplex Mode of the
interface.
Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>
Cc: Tom Rini <trini@ti.com>

Fix the spelling of "configs".
Signed-off-by: NYork Sun <yorksun@freescale.com>
CC: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

A SPL/TPL enabled target would was not recognized as
such by BSD sed, since it relies on a GNU extension.
Instead of or-ing just spell out both matches.

Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

remove the seldomly used EXT2 support because the U-Boot binary will
not fit into the 512KiB flash otherwise.
Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>

fix broken SPI access by adding/activating BOARD_EARLY_INIT_F
functionality and calling spi_init_f() from there.
Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>

Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>

Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>

Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>

Signed-off-by: NDavid Müller <d.mueller@elsoft.ch>

A number of network related files were imported from the LiMon
project; these contain a somewhat unclear license statement:

	Copyright 1994 - 2000 Neil Russell.
	(See License)

I analyzed the source code of LiMon v1.4.2 which was used for this
import.  It does not contain any "License" file, but the top level
directory contains a file "COPYING", which turns out to be GPL v2
of June 1991.  So it is legitimate to conclude that the LiMon derived
files are also to be released under GPLv2.  Mark them as such.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Fix typo of commit d4e53f06.

i2c2 pullup resisters are controlled by bit 0 of CONTROL_PROG_IO1.
It's value after reset is 0x00100001.

In order to clear bit 0, original code write 0xfffffffe to
CONTROL_PROG_IO1 and toggle almost all default values.

Original code affect following:
* disable i2c1 pullup resisters
* increase far end load setting for many modules
* setup invalid SC/LB combination
Signed-off-by: NAlexander Kochetkov <al.kochet@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Steve Kipisz <s-kipisz2@ti.com>

These boards have been orphaned for more than 6 months.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

These boards have been orphaned for more than 6 months.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

This board has been orphaned for more than 6 months.

It is the last board defining CONFIG_APM821XX.
The code inside #ifdef CONFIG_APM821XX should be removed too.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

This board has been orphaned for more than 6 months.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

These boards have been orphaned for more than 6 months.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

In some cases, the last lines of SPL or TPL are not output to a file.
The entries remaining in the "unmatched" variable must be flushed.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: NSimon Glass <sjg@chromium.org>

The definitions for div ratio supposed to be in hex and were added
in dec by mistake.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>

At least on OMAP, init_sata() no longer performs scsi_scan()
so we must do it explicitly here.

Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>

scsi_scan() must be called as part of scsi_init() and not
as part of sata_init().
Signed-off-by: NRoger Quadros <rogerq@ti.com>

On OMAP platforms, SATA controller provides the SCSI subsystem
so implement scsi_init().

Get rid of the unnecessary sata_init() call from dra7xx-evm
and omap5-uevm board files.
Signed-off-by: NRoger Quadros <rogerq@ti.com>

The DMA/FIS buffers are set in ahci_port_start() which is called
after ahci_host_init(). So don't start the DMA engine here
(i.e. don't set FIS_RX)

This fixes the following error at kernel boot on OMAP platforms (e.g. DRA7x)
WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x260/0x358()
44000000.ocp:L3 Custom Error: MASTER SATA TARGET GPMC (Idle): Data Access in User mode during Functional access
Signed-off-by: NRoger Quadros <rogerq@ti.com>

Commit 12cc5437 'omap3: overo: Select
fdtfile for expansion board' wrongly missed the operator in the fdtfile
test. Update the test to only overwrite an empty fdtfile environment
variable.
Signed-off-by: NStefan Herbrechtsmeier <stefan@herbrechtsmeier.net>

Commit 294b91a5 moved initr_malloc
earlier than initr_unlock_ram_in_cache. This causes issue on T4240.
It may be related to locked L1 d-cache and unlocked L2 cache. D-
cache could and should be unlock earlier for normal operation.

This patch moves initr_unlock_ram_in_cache before initr_malloc. It
has been verified on the following boards, in which only T4240QDS
suffered and has been since fixed: T4240QDS, T2080QDS, P5040DS,
P4080DS, MPC8572DS, MPC8536DS, MPC8641HPCN, B4860QDS.
Signed-off-by: NYork Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Simon Glass <sjg@chromium.org>
Acked-by: NSimon Glass <sjg@chromium.org>

On a couple of platforms I've tripped over long PXE append lines overflowing
this array, due to having CONFIG_SYS_CBSIZE == 256. When doing preseeded Debian
installs it's pretty trivial to exceed that.

Since the symptom can be a silent hang or a crash add a check. Of course the
affected boards would also need an increased CBSIZE to actually work.

Note that due to the printing of the final bootargs string CONFIG_SYS_PBSIZE
also needs to be sufficiently large.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
[trini: Use %zd not %d in printf for all args]
Signed-off-by: NTom Rini <trini@ti.com>

In order for the gmac nic to work reliable on the Bananapi, we need to set
bits 10-12 GTXDC "GMAC Transmit Clock Delay Chain" of the GMAC clk register
(0x01c20164) to 3.

Without this about 9 out of 10 ethernet packets get lost, with this setting
there is no packet loss.

So far setting these bits is only necessary on the Bananapi, so this commit
solves this with a bit of #ifdef CONFIG_BANANAPI code. If in the future we
need to do something similar for other boards, we can create a specific
CONFIG_FOO option for this then.
Reported-by: NKarsten Merker <merker@debian.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Tested-by: NKarsten Merker <merker@debian.org>
Tested-by: NZoltan HERPAI <wigyori@openwrt.org>
Tested-by: NTony Zhang <tony.zhang@lemaker.org>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

Removed settings in unsupported register fields. They didn’t
do anything, and in most cases, were not documented in the
reference manual.

Changed register settings to comply with JEDEC required values.

Changed timing parameters because they included full clock
periods that were doing nothing.
Signed-off-by: NAnthony Felice <tony.felice@timesys.com>
[rebased on v2014.10-rc2]
Signed-off-by: NStefan Agner <stefan@agner.ch>

Signed-off-by: NTom Rini <trini@ti.com>

Fix a trivial conflict in dw_mmc.c after talking with Marek.

Conflicts:
	drivers/mmc/dw_mmc.c
Signed-off-by: NTom Rini <trini@ti.com>

Without NULL termination, various commands will read past the
end of input. In particular, this was noticed with error()
calls in cb_getvar and simple_strtoul() in cb_download.

Since the download callback happens elsewhere, the 4k buffer
should always be sufficient to handle command arguments.
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>

This bit allows the MUSB controller to negotiate for high-speed mode when
the device is reset by the hub. If unset, Babble errors occur with
high-speed mass storage devices right after the first packet. This condition
is not caught by the interrupt handles in U-Boot, so no recovery is done,
and the USB communication is stuck.

To fix this, set the bit unconditionally, not only for
CONFIG_USB_GADGET_DUALSPEED but also for host-only modes.
Signed-off-by: NDaniel Mack <zonque@gmail.com>

Enable and use the CONFIG_CMD_FS_GENERIC to avoid hard-coding the
filesystem type into the environment.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: NPavel Machek <pavel@denx.de>

Split the SoCFPGA configuration into SoC-specific part which is
common for all boards (socfpga_cyclone5_common.h) and a board
specific part. There is currently only one board, which is the
generic SoCFPGA board (socfpga_cyclone5.h), but there are more
to come.

This is necessary due to various features of the boards, which
unfortunatelly cannot be autodetected.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: NPavel Machek <pavel@denx.de>

Reorganize and cleanup the configuration file for SoCFPGA. There
is no functional change after this cleanup. This was necessary,
since the file was a wild mess and it was impossible to make sense
of it's content, let alone change something without breaking some
other thing. This patch puts the contents on par with regular U-Boot
standards.

Also remove unused preprocessor symbols CONFIG_SINGLE_BOOTOADER
and CONFIG_USE_IRQ, which is undefined by default. Finally, do
logical reordering of the defines in the file so it's much more
readable. The reordering was also necessary for the splitting
as the initial one was messy.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>

Add command to enable and disable the bridges between HPS and FPGA.

This patch does have a checkpatch issue with the assembler portion,
checkpatch correctly complains that there should be no whitespace
before quoted newline. I do not agree that fixing this specific
checkpatch issue will improve the readability, thus this one is not
addressed.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>

Move icache_enable() and dcache_enable() function calls from
board code into the CPU code and into the enable_caches()
function. This is how the cache enabling code was designed
to work.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: NPavel Machek <pavel@denx.de>

Enable the SDMMC boot as default boot for SOCFPGA U-Boot dev kit.
Enable the bootz command as zImage is used instead uImage.
Signed-off-by: NChin Liang See <clsee@altera.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: NPavel Machek <pavel@denx.de>