Instead of sprinkling custom code and calls over the Vexpress64
boardfile, create a command that loads images using semihosting
just like we would load from flash memory of over the network,
using a special command:

    smhload <image> <address>

This will make it possible to remove some custom calls and
code and make the boot easier.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The semihosting trap call does not like being inlined, probably
because that will mean register reordering screwing up the return
value in r0, so tag this function "noinline".
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

config_distro_bootcmd.h defines a common boot environment for multiple
platforms, including several environment variables that are intended for
interactive use by an end-user.  Document which variables are considered
public interfaces that must remain compatible in future u-boot versions.
Signed-off-by: NKarsten Merker <merker@debian.org>
Acked-by: NStephen Warren <swarren@nvidia.com>

Reuse the 32-bit ARM client architecture and identify ARMv8 specifically
by setting the BOOTP VCI string.

Cc: Dennis Gilmore <dennis@ausil.us>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The bootz command doesn't work with Linux kernel images on 64-bit ARM.
The replacement command with the same interface and functionality is
booti.

Cc: Dennis Gilmore <dennis@ausil.us>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

since we have possibility to write out on lcd whats going on, we don't need
the gpio blink functionality anymore.
Signed-off-by: NHannes Petermaier <hannes.petermaier@br-automation.com>
Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>

At this time I2C and responsible pin-mux is setup during PMIC initialziation
within common.c, this is possible because today PMIC is always connected on
I2C0.

In Future this will be changed, PMIC isn't anymore connected to bus0 in call
cases.

So we do following:
- rename enable_i2c_pin_mux0 to enable_i2c_pin_mux to be generic for enabling
  pin-mux on different or more busses.
- move the call to i2c_pin_mux and i2c_init from common.c to the specific
  board.c
Signed-off-by: NHannes Petermaier <hannes.petermaier@br-automation.com>
Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>

Enable saveenv command and the configs to store environment
persistently in the SD card.

Tested on OMAP4 Panda (OMAP4460 ES1.1)
Signed-off-by: NMaxin B. John <maxin.john@enea.com>
Acked-by: NLokesh Vutla <lokeshvutla@ti.com>

Collect CPU specific flags into the single place.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>

Move the CPU type config options from include/configs/*.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf547x_8x/config.mk.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>

Move the CPU type config options from include/configs/M5235EVB.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf523x/config.mk.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>

Move the CPU type config options from include/configs/M52277EVB.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf5227x/config.mk.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>

This commit intends to stop grepping CPU type in
arch/m68k/cpu/mcf5445x/config.mk.

Move the CPU type config options from include/configs/*.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf5445x/config.mk.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>

This commit intends to stop grepping CPU type in
arch/m68k/cpu/mcf532x/config.mk.

Move the CPU type config options from include/configs/*.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf532x/config.mk.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>

This commit intends to stop grepping CPU type in
arch/m68k/cpu/mcf530x/config.mk.

Move the CPU type config options from include/configs/amcore.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf530x/config.mk.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>

This commit intends to stop grepping CPU type in
arch/m68k/cpu/mcf52x2/config.mk.

Move the CPU type config options from include/configs/*.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf52x2/config.mk.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>

Use filechk to generate asm-offsets.h and generic-asm-offsets.h.
Based on a patch by Valdis Kletnieks.
Reported-by: NValdis Kletnieks <Valdis.Kletnieks@vt.edu>
Acked-by: NValdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reviewed-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NMichal Marek <mmarek@suse.cz>
[ imported from Linux Kernel, commit 70a4fd6c56d0,
  with adjustment for U-Boot ]
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

This line produces an extra comment line for generic-asm-offsets.h
and asm-offsets.h.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: NMichal Marek <mmarek@suse.cz>
[ imported from Linux Kernel, commit 343d3e6cc861,
  with modification of commit description ]
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

The rules "cmd_generic-offsets" and "cmd_offsets" are almost the
same. (The difference is only the include guards.)
They can be merged.

This commit is mostly inspired by the following commit of Linux.

    commit 39664e2f3cdef98f42437e903159a6044a1d99d6
    Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
    Date:   Mon Jan 5 15:57:15 2015 +0900

        kbuild: merge bounds.h and asm-offsets.h rules
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Move arch/arm/include/asm/arch-bcm283x/*
  -> arch/arm/mach-bcm283x/include/mach/*
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>

BCM2835 (used on Raspberry Pi) and BCM2836 (used on Raspberry Pi 2)
are similar enough.  One of the biggest differences is the ARM
processor.  It is reasonable to collect the source files into a
single place, arch/arm/mach-bcm283x/.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>

This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory.  Devices are scanned twice, before/after
relocation.  CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation.  As it is board-independent, handle it
globally.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NRobert Baldyga <r.baldyga@samsung.com>

The default value of CONFIG_SYS_MALLOC_F_LEN is defined by ./Kconfig
as 0x400.  Each defconfig or Kconfig need not repeat the same value.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NRobert Baldyga <r.baldyga@samsung.com>

All the M68000 boards have switched to Generic Board.
This file is no longer necessary.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Huan Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Reviewed-by: NSimon Glass <sjg@chromium.org>

We have done with the generic board conversion for all the boards
of ARC, Blackfin, M68000, MicroBlaze, MIPS, NIOS2, Sandbox, X86.

Let's select SYS_GENERIC_BOARD for those architectures, so we can
tell which architecture has finished the conversion at a glance.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NAlexey Brodkin <abrodkin@synopsys.com>

Move the option to Kconfig renaming it to CONFIG_HAVE_GENERIC_BOARD.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NAlexey Brodkin <abrodkin@synopsys.com>

We have switched to the single .config configuration system,
the same one as used in Linux Kernel.

The necessary glue code is small enough now, so move it to the
top-level Makefile and scripts/kconfig/Makefile, and then delete
scripts/multiconfig.sh.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This target was added by commit cbdd9a97 (sunxi: kconfig: Add
%_felconfig rule to enable FEL build of sunxi platforms.).

At that time, U-Boot used separate .config files for U-Boot proper
and SPL.  I understood the pain to modify both .config and
spl/.config.

Now, we have switched to single .config configuration.
It seems acceptable to run "make menuconfig" or friends to enable
CONFIG_SPL_FEL, as we do for other CONFIGs.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

board/sunxi/board.c tries to set ldo3 to 2.8v however drivers/power/axp209.c
contains an incorrect limit on ldo3 of 2.275v

The origin of the incorrect limit seems likely due to some inconsistencies
in the axp209 datasheet. ldo3 is described with different limits in
different sections. register 0x29 uses 7 bits for voltage configuration
while the 2.275v limit would apply if only 6 bits were used.
Probably this is a cut&paste error from register 0x23

The linux kernel driver has the correct limit and operation up to the 2.8v
required by my board has been physically verified with a multimeter.
Signed-off-by: NIain Paton <ipaton0@gmail.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Of 4 boards in our automated test system 2 do not have reliable
networking with the default TX delay of 0x0. Increasing to 0x1 seems
to make things reliable on all 4 boards.

Some previous ad-hpoc tests with tx delay set to 0, 1, 2 and 3 on one
of the problematic boards showed:

0: mw.l 0x1c20164 0x006 1     -- t/o in 4/5 tftp runs
1: mw.l 0x1c20164 0x406 1     -- t/o in 1/5 tftp runs
2: mw.l 0x1c20164 0x806 1     -- t/o in 1/5 tftp runs
3: mw.l 0x1c20164 0xc06 1     -- t/o many times in first tftp run

For 0, 1 and 2 "t/o" means one or two "T" glitches in the download,
but it did complete. For 3 those were basically continuous and it
couldn't complete.

tftp was of a 16M initrd.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Serial-uclass should be generically implemented without depending
a particular hardware.  Fortunately, nothing in include/ns16550.h is
referenced from drivers/serial/serial-uclass.c, so remove this bogus
include.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Acked-by: NSimon Glass <sjg@chromium.org>

List bootable partitions and only scan those for bootable files, falling
back to partition 1 if there are no bootable partitions
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>

env exists allows scripts to query whether an environment variable
exists. Enable by default as it adds only a trivial amount of code and
can be useful in scripts.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>

Add an optional -bootable parameter to the part list commands to only
put the list of bootable partitions in the environment variable
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NStephen Warren <swarren@nvidia.com>

It is very common in the debug stage to test U-Boot loading a linux
kernel. The commands to boot linux kernel with ramdisk and nfs as the
root are common to all x86 targets, so it makes sense to add them as
the U-Boot default environment in x86-common.h.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chroimum.org>

Saving U-Boot's environment in SPI flash on Intel Galileo board.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sg@chromium.org>

Saving U-Boot's environment in SPI flash on Intel CrownBay board.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sg@chromium.org>