* Add support for P3G4 board

* Fix problem with MGT5100 FEC driver: add "early" MAC address
  initialization

According to the MPC8260 User's Manual, PCI_MODE signal should be
reflected in SCCR register, and local bus pins configuration is taken
from HRCW and appears in SIUMCR. For some reason it does not work
this way, so the only possibility to detect if the board is
configured in PCI mode is to check the BCSR. This patch sets SCCR and
SIUMCR according to the BCSR.

add support for Adder II MPC852T module

  fix TI Innovator/OMAP1510 pin configs

* Patches by Kshitij, 18 Aug 2003
  - add support for arm926ejs cpu core
  - add support for TI OMAP 1610 Innovator Board

add support for bzip2 uncompression

(because of better response to iprobe command); fix problem with
"reset" command

* Fix RAM size detection for RMU board

* Implement "reset" for MGT5100/MPC5200 systems

  allow selection of clock frequency as "make" target

* Implement memory autosizing code for IceCube boards

* Configure network port on INCA-IP for autonegotiation

* Fix overflow problem in network timeout code

* Patch by Richard Woodruff, 8 Aug 2003:
  Allow crc32 to be used at address 0x000 (crc32_no_comp, too).

disable clocks_in_mhz, enable boot count limit

in toplevel directory instead.  Removed astest.c from tools/gdb because
it is no longer relevant.

Fix MPC5200 FEC driver

in toplevel directory instead.  Removed astest.c from tools/gdb because
it is no longer relevant.

* Patch by Brad Parker, 02 Aug 2003:
  fix sc520_cdp problems

* Implement Boot Cycle Detection (Req. 2.3 of OSDL CGL Reqirements)

* Allow erase command to cross flash bank boundaries

  Add support for LynuxWorks Kernel Downloadable Images (KDIs).
  Both LynxOS and BlueCat linux KDIs are supported.

* Patch by Richard Woodruff, 25 Jul 2003:
  use more reliable reset for OMAP/925T

* Patch by Nye Liu, 25 Jul 2003:
  fix typo in mpc8xx.h

* Patch by Richard Woodruff, 24 Jul 2003:
  Fixes for cmd_nand.c:
  - Fixed null dereferece which could result in incorrect ECC values.
  - Added support for devices with no Ready/Busy signal hooked up.
  - Added OMAP1510 read/write protect handling.
  - Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock
    for non-JFFS2.
  - Switched default ECC to be JFFS2.

* Provide consistent interface to standalone applications to access
  the 'global_data' structure
  Provide a doc/README.standalone more useful to users/developers.

* Make IceCube MGT5100 FEC driver work

  applications: instead of using (PPC-specific) system calls we now
  use a jump table; please see doc/README.standalone for details

* Patch by Dave Westwood, 24 Jul 2003:
  added support for Unity OS (a proprietary OS)

  add delay to get I2C working with "imm" command and s3c24x0_i2c.c

* Patch by Richard Woodruff, 17 July 03:
  - Fixed bug in OMAP1510 baud rate divisor settings.

* Patch by Nye Liu, 16 July 2003:
  MPC860FADS fixes:
  - add MPC86xADS support (uses MPC86xADS.h)
  - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
    o PLPRCR changes
    o BRG changes (EXTAL/XTAL restricted to 10MHz)
    o don't trust gclk() software measurement by default, depend on
      CONFIG_8xx_GCLK_FREQ
  - add DRAM SIMM not installed detection
  - use more "correct" SDRAM initialization sequence
  - allow different SDRAM sizes (8xxADS has 8M)
  - default DER is 0
  - remove unused MAMR defines from FADS860T.h (all done in fads.c)
  - rename MAMR/MBMR defines to be more consistent. Should eventually
    be merged into MxMR to better reflect the PowerQUICC datasheet.

* Patch by Yuli Barcohen, 16 Jul 2003:
  support new Motorola PQ2FADS-ZU evaluation board which replaced
  MPC8260ADS and MPC8266ADS

* Add support for MGT5100 and MPC5200 processors

make logbuf compile without POST

- added support for arm925t cpu core
- added support for TI OMAP 1510 Innovator Board

  - add I2C support for s3c2400 systems (trab board)
  - (re-) add "ping" to command table

* Fix handling of "slow" POST routines

  - Correct flash and JFFS2 support for MPC8260ADS
  - fix PVR values and clock generation for PowerQUICC II family
    (8270/8275/8280)

* Patch by Bernhard Kuhn, 08 Jul 2003:
  - add support for M68K targets

* Patch by Ken Chou, 3 Jul:
  - Fix PCI config table for A3000
  - Fix iobase for natsemi.c
    (PCI_BASE_ADDRESS_0 is the IO base register for DP83815)

* Allow to enable "slow" POST routines by key press on power-on
* Fix temperature dependend switching of LCD backlight on LWMON
* Tweak output format for LWMON

* Add support for TQM823M, TQM850M, TQM855M and TQM860M modules

* Add support for Am29LV160ML, Am29LV320ML, and Am29LV640ML
  mirror bit flash on TQM8xxM modules

get rid of MK_CMD_ENTRY macro; update doc/README.command

  Improve documentation of I2C configuration in README

* Fix problems with previous log buffer "fixes"

* Fix minor help text issues

* "log append" did not append a newline

(autoscript, bmp, bsp, fat, mmc, nand, portio, ...)