Change my email address, too many mails
gets to my private mail, created specific email
account just for developmement.
Signed-off-by: NRamon Fried <ramon.fried@gmail.com>

- pinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groups
- pinctrl: meson-gxbb: add hdmi related pins to fix HDMI on GXBB
- pinctrl: meson: add support for getting pinmux status
- pinctrl: meson-g12a: add support for drive-strength-microamp property

Pull request for UEFI sub-system for v2019.07-rc5

This pull request provides fixes for event services.

The GXBB pinctrl is missing pins related to HDMI, namely hot plug
detection (hpd) and I2C (sda + scl).

This fixes HDMI support for GXBB in u-boot.
Reported-by: NMohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: NMaxime Jourdan <mjourdan@baylibre.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Tested-by: NMohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

add drive-strength bank regiter and bit value for G12A SoC
Signed-off-by: NGuillaume La Roque <glaroque@baylibre.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

drive-strength-microamp is a new feature needed for G12A SoC.
the default DS setting after boot is usually 500uA and it is not enough for
many functions. We need to be able to set the drive strength to reliably
enable things like MMC, I2C, etc ...
Signed-off-by: NGuillaume La Roque <glaroque@baylibre.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

Add drive-strength-microamp property support to allow drive strength in uA
Signed-off-by: NGuillaume La Roque <glaroque@baylibre.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

In order to support the "pinmux status" command, use the common functions
to get the pins count and names, and add the AXG specific function to get
the current function from registers.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

In order to support the "pinmux status" command, use the common functions
to get the pins count and names, and add the GX specific function to get
the current function from registers.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Tested-by: NMaxime Jourdan <mjourdan@baylibre.com>

In order to support the "pinmux status" command, add common function
to get pins count and pin name.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

The GPIO_TEST_N was in the wrong pmx group table, move it back with the AO
groups, GPIODV_18 was missing, add it back, and finally the GPIOCLK_*
group names were missing.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board

u-boot-imx-20190612
--------------------

- Board fixes:
	- imx6logic
	- wandboard
	- mx6sabre boots again
	- imx8qm_mek
	- pico-* boards
	- Toradex apalis / colibri
	- engicam imx6 (environment)
	- KP MX53
	- opos6ul
- Switch to DM:
	- vining2000
	- dh MX6
	- Toradex colibri i.MX7
	- Novena
- Security : fix CSF size for HAB
- Other:
      - imx: fix building for i.mx8 without spl
      - pcie and switch to DM

      mx6sabreauto: Enable SPL SDP support

The SPL for the Tinker Board has to fit into 32 KiB. Currently this limit
is exceeded.

CONFIG_SPL_I2C_SUPPORT is not needed to move to main U-Boot. So let's
disable it.
Suggested-by: NDavid Wu <david.wu@rock-chips.com>
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NDavid Wu <david.wu@rock-chips.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

As explained in include/configs/imx6_spl.h. the i.MX6 SPL
size limit is 68KB (4KB header + 64KB max size).

Provide such limit for all i.MX6 boards that use SPL
to detect SPL size overflow in build time.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>

To allow loading u-boot over USB enable SDP support in the SPL.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

The i.mx6 SPL binary cannot be bigger then 68K, while with the current
defconfig for sabreauto it's only about 56K as soon as USB support gets
added the size will overflows.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

All i.mx6 boards seems to have moved to DM_USB, however gadget support
for mx6 is still pre-DM as CI_UDC isn't converted yet. To make this work
the usb otg controller used for gadgets needs to be usb number 0.
Add an alias for this directly in the main u-boot mx6qdl dtsi so it
doesn't need to be done for each board separately.

This fixes regressions wrt. usb gadget functionality in several boards
that have gadget functions enabled in their config, but no usb0 alias in
their device-tree.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>

Sabre Auto boards currently hang with:
```
U-Boot 2019.07-rc3-00057-gc41940c406 (Jun 03 2019 - 14:42:41 +0200)

CPU:   Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz)
CPU:   Automotive temperature grade (-40C to 125C)Reset cause: WDOG
Model: Freescale i.MX6 Quad Plus SABRE Automotive Board
Board: MX6Q-Sabreauto revA
I2C:   ready
DRAM:  2 GiB
Video device 'ipu@2400000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Video device 'ipu@2800000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Some drivers failed to bind
Error binding driver 'generic_simple_bus': -28
Some drivers failed to bind
initcall sequence 8ffe00b8 failed at call 1780e93b (err=-28)
```

Set SYS_MALLOC_F_LEN to reserve_video to work.

This is similar to the change Peng Fan did for mx6sabresd (9002e735)
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

With the conversion to DM we should select the pinctrl driver.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

Staticize 'spl_dram_init' and 'i2c_pad_info1' to fix the
following sparse warnings:

board/freescale/imx8mq_evk/spl.c:30:6: warning: symbol 'spl_dram_init' was not declared. Should it be static?
board/freescale/imx8mq_evk/spl.c:41:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static?
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

Without this definition, fsl_esdhc will access reserved registers
on i.MX chips, so define ARCH_MXC to fix it.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

imx-regs.h under arch-imx has no user, drop it.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

Read the temperature when print cpu inforation.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

This commit is necessary to be able to re-use the pinctrl code in early
SPL to properly configure pins.

The problem is that those "static" structures (without explicit
initialization) are placed in the SDRAM area, which corresponds to
u-boot proper (not even SPL).
Hence, when one wants to configure pins before relocation via DTS/DM,
the board hangs (imx6q SoC powered one) as only OCRAM area is available
(0x009xxxxx).

This commit prevents from this issue by moving the imx6_pinctrl_soc_info
structure to data section (from BSS).
Signed-off-by: NLukasz Majewski <lukma@denx.de>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

We should not access reserved register on i.MX8, otherwise met SERROR
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Enable DM Serial support on iMX6SX VINING|2000.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

Enable DM PCI support on iMX6SX VINING|2000.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

Enable DM GPIO support on iMX6SX VINING|2000 and fix up
board code where applicable.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

Enable DM USB support on iMX6SX VINING|2000.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

Enable DM block and DM MMC support on iMX6SX VINING|2000 .
Convert board code to match the DM support. This disables
USB mass storage support due to missing DM USB, however
that will be re-enabled in subsequent patch.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

Enable DM pin control support on iMX6SX VINING|2000.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

Import iMX6SX VINING|2000 device tree from Linux 5.1.1 b724e9356404 .
Enable DT control in full U-Boot .
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

This patch configures pinmux for pin usdhc4 reset.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>

Add imx dts files to the MAINTAINERS file list, so that i.MX
devicetree related patches can be properly sent to the i.MX folks.
Reported-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

Add compatible string for iMX6SX.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

Enable DM PCI support on iMX6Q Novena.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>

Add DM support and support for probing the iMX PCI driver from DT.
The legacy non-DM support is retained, however shall be removed once
DM PCI is the only option remaining.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Pass the driver private data around the driver as much as possible, instead
of having it as a static global variable. This is done in preparation for
the DM conversion, no functional change.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>