This enables the device tree library on the Integrator platforms
so we can pass a device tree when booting.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As this board has NAND and supports YAFFS2, add CONFIG_MD_NAND_YAFFS

Cc: David Müller <d.mueller@elsoft.ch>
Signed-off-by: NTom Rini <trini@ti.com>
Acked-by: NDavid Müller <d.mueller@elsoft.ch>

Conflicts:
	drivers/video/exynos_fb.c

ext3 should not be used on SD cards, so use ext4 instead.

Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>

The processor is hopefully running with M(ega)Hz and not with m(illi)Hz.
Signed-off-by: NManfred Huber <man.huber@arcor.de>

The previous timings were done on the internal-only A1 board which has
different DDR part than all later revs.  The timings need a slight
adjustment to be correct in all cases with later revs.
Signed-off-by: NTom Rini <trini@ti.com>

This board is from a u-boot point of view a mixture between kmnusa and
a standard km_kirkwood board. We have our u-boot environment in the spi
NOR flash, but we have a direct connection between the kirkwood and the
piggy. A FPGA is connected via the PCIe interface. So we only have to
select the specific features in the board setup.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-By: NPrafulla Wadaskar <prafulla@marvell.com>

Switch from 1-bit ecc to 4-bit ecc.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-By: NPrafulla Wadaskar <prafulla@marvell.com>

commit 9660e442 cosmetic: s/BOARD_LATE_INIT/CONFIG_BOARD_LATE_INIT
removes BOARD_LATE_INIT and uses CONFIG_BOARD_LATE_INIT instead.
Therefore we have to use this define.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: NPrafulla Wadaskar <prafulla@marvell.com>

If CONFIG_NAND_ECC_BCH is set use 4-bit error correction code instead of
the 1-bit error correction code on the NAND device.
Signed-off-by: NGerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: NPrafulla Wadaskar <prafulla@marvell.com>
Acked-by: NScott Wood <scottwood@freescale.com>

The conversion of mx31pdk to SPL NAND fixed the boot issue, but we start seeing
resets in loop, which prevents us from reaching the U-boot prompt.

Until the proper fix can be identified, disable watchdog, so that mx31pdk
can be functional again.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NStefano Babic <sbabic@denx.de>

Let all ARM linker scripts handle properly -ffunction-sections
and -fdata-sections. This will be useful for future changes in order to create
symbol-specific sections in common .S files.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

Following the removal of the smdk6400 board, the MMU setup code in
arm1176/start.S becomes unused, so remove it. It will still be possible to
restore it later from the Git history if necessary, in which case it should be
moved out of the relocate_code() function.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

This reverts commit 1285a280 since the migration
of boards from Makefile to boards.cfg is now complete.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

The migration of boards from Makefile to boards.cfg was due for v2012.03, but
smdk6400 did not follow, and it does not build, so move it to scrapyard. It will
still be possible to restore it from the Git history before fixing it.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

This image combines the SPL with the i.MX header, the FCB and U-Boot.

For i.MX25/35/51, the FCB is ignored by the boot ROM, so this image is just
useful because it can be programmed on a NAND Flash page boundary.

For i.MX53, the FCB is required by the boot ROM.

This does not support i.MX6 so far because its FCB is more complicated.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

This image combines the SPL with the i.MX header and U-Boot. This is a
convenient way of having a single image to program on some boot devices.

The i.MX header has to be added to the SPL before appending U-Boot, so that the
boot ROM loads only the SPL.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

make never uses the SHELL variable from the environment. Instead, it
uses /bin/sh, or the value assigned to the SHELL variable by the Makefile. This
makes the export of the SHELL variable useless for sub-makes (but still useful
for the environment of recipes). However, we want all makes to use the same
shell.

This patch fixes this issue by moving the SHELL variable setup and export to the
top config.mk, so that all Makefile-s including it use the same shell.

Since BASH is used by default, this makes it possible to use things
like 'echo -e ...' in sub-makes, which would otherwise fail e.g. with /bin/sh
symlinked to /bin/dash on Ubuntu.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: NTom Rini <trini@ti.com>

Commit e05e5de7 made the 2 1st parameters of
ARM's relocate_code() useless since it moved the code handling them to crt0.S.
So, drop these parameters.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

This also fixes support for mx31pdk and tx25, which had been broken by commit
e05e5de7.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>

Automatically build the 'u-boot.imx' (i.e. imx header + u-boot.bin) and 'SPL'
(i.e. imx header + u-boot-spl.bin) make targets for all imx processors
supporting this header, so for arm926ejs, arm1136 and armv7. Some combinations
were missing.

At the same time, fix the build of SPL targets not supporting the imx header on
arm1136. For arm1136, the 'SPL' make target was forced to build in all cases if
CONFIG_SPL_BUILD was defined, even for non-imx platforms or imx setups without
an imx header.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

Change CONFIG_SPL_PAD_TO from a link address to an image offset since this is
more handy and closer to the purpose of this config.

Automatically define CONFIG_SPL_PAD_TO to CONFIG_SPL_MAX_SIZE (or 0 without
CONFIG_SPL_MAX_SIZE).

Test that CONFIG_SPL_PAD_TO >= CONFIG_SPL_MAX_SIZE if CONFIG_SPL_PAD_TO is
non-zero.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

Give more flexibility to define configs that can be interpreted by make, e.g. to
define fallback values of configs like in the example below.

Before this change, the config lines:
 #define CONFIG_SPL_MAX_SIZE	2048
 #define CONFIG_SPL_PAD_TO	CONFIG_SPL_MAX_SIZE
would have been changed in autoconfig.mk into:
 CONFIG_SPL_MAX_SIZE=2048
 CONFIG_SPL_PAD_TO="CONFIG_SPL_MAX_SIZE"

Hence, a make recipe using as an argument to $(OBJCOPY):
 --pad-to=$(CONFIG_SPL_PAD_TO)
would have issued:
 --pad-to="CONFIG_SPL_MAX_SIZE"
which means nothing for $(OBJCOPY) and makes it fail.

Thanks to this change, the config lines above are changed in autoconfig.mk into:
 CONFIG_SPL_MAX_SIZE=2048
 CONFIG_SPL_PAD_TO=$(CONFIG_SPL_MAX_SIZE)

Hence, the make recipe above now issues:
 --pad-to=2048
as expected from the defined config.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: NTom Rini <trini@ti.com>

The purpose of .globl is to export symbols for ld, not to declare external
symbols.

By the way, use the ENTRY() and ENDPROC() macros to define functions rather than
using .global directly.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

Use __image_copy_end instead of __bss_start for the end of the image to
relocate. This is the same as commit 033ca724, but applied to all ARM start.S.

This is a more appropriate symbol naming for an image copy & relocate feature,
and this also saves a useless copy of data put between __image_copy_end and
__bss_start in linker scripts (e.g. relocation information, or MMU
initialization tables used only before jumping to the relocated image).
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

Commit e05e5de7 made ARM's relocate_code()
return to its caller, but it did not update its declaration accordingly.

Fixing this function declaration fixes dropped C code following calls to
relocate_code().
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>

_TEXT_BASE must be set to CONFIG_SPL_TEXT_BASE for generic SPL, and to
CONFIG_SYS_TEXT_BASE for non-SPL builds.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: NTom Rini <trini@ti.com>

The syndrome functions should use the page number passed as argument instead of
the page number saved upon NAND_CMD_READ0.

This does not make any difference if the NAND_NO_AUTOINCR option is set, but
otherwise this fixes accesses to the wrong pages.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: NScott Wood <scottwood@freescale.com>

The page number indicated in the debug trace of mxc_nand_read_oob_syndrome() did
not match the page being worked on.

By the way, replace the GCC-specific __FUNCTION__ with __func__.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: NScott Wood <scottwood@freescale.com>

Add support for the Samsung K9LAG08U0M NAND Flash (2-GiB MLC NAND Flash, 2-kiB
pages, 256-kiB blocks, 30-ns R/W cycles, 1 CS) on mx53ard.

eNFC_CLK_ROOT is set up with a cycle time of 37.5 ns (400 MHz / 3 / 5) for this
board, which satisfies the 30-ns NF R/W cycle requirement.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>

Don't use several instructions to build constant values.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: NStefano Babic <sbabic@denx.de>

Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>