For T4 platform, the SRIO LIODN registers are in SRIO address space
and not in GUTs.
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>

For B4, the SRIO LIODN registers are in SRIO address space and not
in GUTs.
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: NTom Rini <trini@ti.com>

Erratum A-006593 is "Atomic store may report failure but still allow
the store data to be visible".

The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit
21 to 1'b1.  This may have a small impact on synthetic write bandwidth
benchmarks but should have a negligible impact on real code."
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Calculate reserved fields according to IFC bank count

1. Move csor_ext register behind csor register and fix res offset
2. Move ifc bank count to config_mpc85xx.h to support 8 bank count
3. Guard fsl_ifc.h with CONFIG_FSL_IFC macro to eliminate the compile
   error on some devices that does not have IFC controller.
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable
the master module of Boot from SRIO and PCIE on a platform. But this
is not a silicon feature, it's just a specific booting mode based on
the SRIO and PCIE interfaces. So it's inappropriate to put the macro
into the file arch/powerpc/include/asm/config_mpc85xx.h.

Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to
"CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from
arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros
in configuration header file of each board which can support the
master module of Boot from SRIO and PCIE.
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

BSC9132 has 3 IFC banks.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

BSC9131RDB is a Freescale Reference Design Board for
BSC9131 SoC which is a integrated device that contains
one powerpc e500v2 core and one DSP starcore.

To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 memory
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

B4420 is a subset of B4860. Merge them in config_mpc85xx.h to simplify
the defines.
- Removed #define CONFIG_SYS_FSL_NUM_CLUSTERS as this is used nowhere.
- defined CONFIG_SYS_NUM_FM1_10GEC to 0 for B4420 as it does not have 10G.

Also move CONFIG_E6500 out of B4860QDSds.h into config_mpc85xx.h.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

To align with chassis generation 2 spec, all cores are numbered in sequence.
The cores may reside across multiple clusters. Each cluster has zero to four
cores. The first available core is numbered as core 0. The second available
core is numbered as core 1 and so on.

Core clocks are generated by each clusters. To identify the cluster of each
core, topology registers are examined.

Cluster clock registers are reorganized to be easily indexed.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

T1040 and variants have e5500 cores and are compliant to QorIQ Chassis
Generation 2. The major difference between T1040 and its variants is the
number of cores and the number of L2 switch ports.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

T4160 is a subset of T4240. Merge them in config_mpc85xx.h to simplify
the defines. Also move CONFIG_E6500 out of t4qds.h into config_mpc85xx.h.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

T4160 SoC is low power version of T4240. The T4160 combines eight dual
threaded Power Architecture e6500 cores and two memory complexes (CoreNet
platform cache and DDR3 memory controller) with the same high-performance
datapath acceleration, networking, and peripheral bus interfaces.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

T4240 internal UTMI phy is different comparing to previous UTMI PHY
in P3041.
This patch adds USB 2.0 UTMI Dual PHY new memory map and enable it for
T4240.
The phy timing is very sensitive and moving the phy enable code to
cpu_init.c will not work.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Erratum DDR_A003 applies to P5020, P3041, P4080, P3060, P2041, P5040.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

As per Errata list of BSC9131 and BSC9132, IFC Errata A003399 is no more
valid. So donot compile its workaround.
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal
multi-bit ECC errors, which has impact on performance, so software should
disable all ECC reporting from USB1 and USB2.

In formal release document, the errata number should be USB14 instead of USB138.
Signed-off-by: Nxulei <Lei.Xu@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: Nxulei <B33228@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Per the latest errata updated, B4860/B4420 Rev 1.0 has also
errata A-005871, so adding define A-005871 for B4 SoCs.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

When CoreNet Fabric (CCF) internal resources are consumed by the cores,
inbound SRIO messaging traffic through RMan can put the device into a
deadlock condition.

This errata workaround forces internal resources to be reserved for
upstream transactions. This ensures resources exist on the device for
upstream transactions and removes the deadlock condition.

The Workaround is for the T4240 silicon rev 1.0.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

The BSC9132 is a highly integrated device that targets the evolving
 Microcell, Picocell, and Enterprise-Femto base station market subsegments.

 The BSC9132 device combines Power Architecture e500 and DSP StarCore SC3850
 core technologies with MAPLE-B2P baseband acceleration processing elements
 to address the need for a high performance, low cost, integrated solution
 that handles all required processing layers without the need for an
 external device except for an RF transceiver or, in a Micro base station
 configuration, a host device that handles the L3/L4 and handover between
 sectors.

 The BSC9132 SoC includes the following function and features:
    - Power Architecture subsystem including two e500 processors with
	512-Kbyte shared L2 cache
    - Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte private L2
	cache
    - 32 Kbyte of shared M3 memory
    - The Multi Accelerator Platform Engine for Pico BaseStation Baseband
      Processing (MAPLE-B2P)
    - Two DDR3/3L memory interfaces with 32-bit data width (40 bits including
      ECC), up to 1333 MHz data rate
    - Dedicated security engine featuring trusted boot
    - Two DMA controllers
         - OCNDMA with four bidirectional channels
         - SysDMA with sixteen bidirectional channels
    - Interfaces
        - Four-lane SerDes PHY
	    - PCI Express controller complies with the PEX Specification-Rev 2.0
        - Two Common Public Radio Interface (CPRI) controller lanes
	    - High-speed USB 2.0 host and device controller with ULPI interface
        - Enhanced secure digital (SD/MMC) host controller (eSDHC)
	    - Antenna interface controller (AIC), supporting four industry
		standard JESD207/four custom ADI RF interfaces
       - ADI lanes support both full duplex FDD support & half duplex TDD
       - Universal Subscriber Identity Module (USIM) interface that
	   facilitates communication to SIM cards or Eurochip pre-paid phone
	   cards
       - Two DUART, two eSPI, and two I2C controllers
       - Integrated Flash memory controller (IFC)
       - GPIO
     - Sixteen 32-bit timers
Signed-off-by: NNaveen Burmi <NaveenBurmi@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

B4420 is a reduced personality of B4860 with fewer core/clusters(both SC3900
and e6500), fewer DDR controllers, fewer serdes lanes, fewer SGMII interfaces and
reduced target frequencies.

Key differences between B4860 and B4420
----------------------------------------
B4420 has:
1. Fewer e6500 cores: 1 cluster with 2 e6500 cores
2. Fewer SC3900 cores/clusters: 1 cluster with 2 SC3900 cores per cluster.
3. Single DDRC
4. 2X 4 lane serdes
5. 3 SGMII interfaces
6. no sRIO
7. no 10G
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

- Added some more serdes1 and serdes2 combinations
  serdes1= 0x2c, 0x2d, 0x2e
  serdes2= 0x7a, 0x8d, 0x98
- Updated Number of DDR controllers to 2.
- Added FMAN file for B4860, drivers/net/fm/b4860.c
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NShaveta Leekha <shaveta@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NSandeep Singh <Sandeep@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Due to SerDes configuration error, if we set the PCI-e controller link width
as x8 in RCW and add a narrower width(such as x4, x2 or x1) PCI-e device to
PCI-e slot, it fails to train down to the PCI-e device's link width. According
to p4080ds errata PCIe-A003, we reset the PCI-e controller link width to x4 in
u-boot. Then it can train down to x2 or x1 width to make the PCI-e link between
RC and EP.
Signed-off-by: NYuanquan Chen <B41889@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

board configuration file is included before asm/config_mpc85xx.h.
however, CONFIG_FSL_SATA_V2 is defined in asm/config_mpc85xx.h.
it will never take effective in the board configuration file for
this kind of code :

 #ifdef CONFIG_FSL_SATA_V2
 ...
 #endif

To solve this problem, move CONFIG_FSL_SATA_V2 to board
configuration header file.

This patch reverts Timur's
commit:3e0529f7Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

The work-around for erratum A-004580 ("Internal tracking loop can falsely
lock causing unrecoverable bit errors") is implemented via the PBI
(pre-boot initialization code, typically attached to the RCW binary).
This is because the work-around is easier to implement in PBI than in
U-Boot itself.

It is still useful, however, for the 'errata' command to tell us whether
the work-around has been applied.  For A-004580, we can do this by verifying
that the values in the specific registers that the work-around says to
update.

This change requires access to the SerDes lane sub-structure in
serdes_corenet_t, so we make it a named struct.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Once u-boot sets the spin table to cache-enabled memory, old kernel which
uses cache-inhibit mapping without coherence will not work properly. We
use this temporary fix until kernel has updated its spin table code.
For now this fix is activated by default. To disable this fix for new
kernel, set environmental variable "spin_table_compat=no". After kernel
has updated spin table code, this default shall be changed.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

The work-around for erratum A-004849 ("CoreNet fabric (CCF) can exhibit a
deadlock under certain traffic patterns causing the system to hang") is
implemented via the PBI (pre-boot initialization code, typically attached
to the RCW binary).  This is because the work-around is easier to implement
in PBI than in U-Boot itself.

It is still useful, however, for the 'errata' command to tell us whether
the work-around has been applied.  For A-004849, we can do this by verifying
that the values in the specific registers that the work-around says to
update.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

The P5040 has an e5500 core, so CONFIG_SYS_PPC64 should be defined in
config_mpc85xx.h.  This macro was absent in the initial P5040 patch because
it crossed paths with the patch that introduced the macro.

Also delete CONFIG_SYS_FSL_ELBC_MULTIBIT_ECC, since it's not used in the
upstream U-Boot.  It's a holdover from the SDK.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Currently, the SRIO and PCIE boot master module will be compiled into the
u-boot image if the macro "CONFIG_FSL_CORENET" has been defined. And this
macro has been included by all the corenet architecture platform boards.
But in fact, it's uncertain whether all corenet platform boards support
this feature.

So it may be better to get rid of the macro "CONFIG_FSL_CORENET", and add
a special macro for every board which can support the feature. This
special macro will be defined in the header file
"arch/powerpc/include/asm/config_mpc85xx.h". It will decide if the SRIO
and PCIE boot master module should be compiled into the board u-boot image.
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Move spin table to cached memory to comply with ePAPR v1.1.
Load R3 with 64-bit value if CONFIG_SYS_PPC64 is defined.

'M' bit is set for DDR TLB to maintain cache coherence.

See details in doc/README.mpc85xx-spin-table.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

After DDR controller is enabled, it performs a calibration for the
transmit data vs DQS paths. During this calibration, the DDR controller
may make an inaccurate calculation, resulting in a non-optimal tap point.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Boot space translation utilizes the pre-translation address to select
the DDR controller target. However, the post-translation address will be
presented to the selected DDR controller. It is possible that the pre-
translation address selects one DDR controller but the post-translation
address exists in a different DDR controller when using certain DDR
controller interleaving modes. The device may fail to boot under these
circumstances. Note that a DDR MSE error will not be detected since DDR
controller bounds registers are programmed to be the same when configured
for DDR controller interleaving.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

DDRC ver 4.7 adds DDR_SLOW bit in sdram_cfg_2 register. This bit needs to be
set for speed lower than 1250MT/s.

CDR1 and CDR2 are control driver registers. ODT termination valueis for
IOs are defined. Starting from DDRC 4.7, the decoding of ODT for IOs is
	000 -> Termsel off
	001 -> 120 Ohm
	010 -> 180 Ohm
	011 -> 75 Ohm
	100 -> 110 Ohm
	101 -> 60 Ohm
	110 -> 70 Ohm
	111 -> 47 Ohm

Add two write leveling registers. Each QDS now has its own write leveling
start value. In case of zero value, the value of QDS0 will be used. These
values are board-specific and are set in board files.

Extend DDR register timing_cfg_1 to have 4 bits for each field.

DDR control driver registers and write leveling registers are added to
interactive debugging for easy access.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

The multirate ethernet media access controller (mEMAC) interfaces to
10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII
interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface.
Signed-off-by: NSandeep Singh <Sandeep@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Add support for Freescale B4860 and variant SoCs. Features of B4860 are
(incomplete list):

Six fully-programmable StarCore SC3900 FVP subsystems, divided into three
    clusters-each core runs up to 1.2 GHz, with an architecture highly
    optimized for wireless base station applications
Four dual-thread e6500 Power Architecture processors organized in one
    cluster-each core runs up to 1.8 GHz
Two DDR3/3L controllers for high-speed, industry-standard memory interface
    each runs at up to 1866.67 MHz
MAPLE-B3 hardware acceleration-for forward error correction schemes
    including Turbo or Viterbi decoding, Turbo encoding and rate matching,
    MIMO MMSE equalization scheme, matrix operations, CRC insertion and
    check, DFT/iDFT and FFT/iFFT calculations, PUSCH/PDSCH acceleration,
    and UMTS chip rate acceleration
CoreNet fabric that fully supports coherency using MESI protocol between
    the e6500 cores, SC3900 FVP cores, memories and external interfaces.
    CoreNet fabric interconnect runs at 667 MHz and supports coherent and
    non-coherent out of order transactions with prioritization and
    bandwidth allocation amongst CoreNet endpoints.
Data Path Acceleration Architecture, which includes the following:
  Frame Manager (FMan), which supports in-line packet parsing and general
    classification to enable policing and QoS-based packet distribution
  Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading
    of queue management, task management, load distribution, flow ordering,
    buffer management, and allocation tasks from the cores
  Security engine (SEC 5.3)-crypto-acceleration for protocols such as
    IPsec, SSL, and 802.16
  RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and
    outbound). Supports types 5, 6 (outbound only)
Large internal cache memory with snooping and stashing capabilities for
    bandwidth saving and high utilization of processor elements. The
    9856-Kbyte internal memory space includes the following:
  32 Kbyte L1 ICache per e6500/SC3900 core
  32 Kbyte L1 DCache per e6500/SC3900 core
  2048 Kbyte unified L2 cache for each SC3900 FVP cluster
  2048 Kbyte unified L2 cache for the e6500 cluster
  Two 512 Kbyte shared L3 CoreNet platform caches (CPC)
Sixteen 10-GHz SerDes lanes serving:
  Two Serial RapidIO interfaces. Each supports up to 4 lanes and a total
    of up to 8 lanes
  Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue-
    less antenna connection
  Two 10-Gbit Ethernet controllers (10GEC)
  Six 1G/2.5-Gbit Ethernet controllers for network communications
  PCI Express controller
  Debug (Aurora)
Two OCeaN DMAs
Various system peripherals
182 32-bit timers
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Add support for Freescale T4240 SoC. Feature of T4240 are
(incomplete list):

12 dual-threaded e6500 cores built on Power Architecture® technology
  Arranged as clusters of four cores sharing a 2 MB L2 cache.
  Up to 1.8 GHz at 1.0 V with 64-bit ISA support (Power Architecture
    v2.06-compliant)
  Three levels of instruction: user, supervisor, and hypervisor
1.5 MB CoreNet Platform Cache (CPC)
Hierarchical interconnect fabric
  CoreNet fabric supporting coherent and non-coherent transactions with
    prioritization and bandwidth allocation amongst CoreNet end-points
  1.6 Tbps coherent read bandwidth
  Queue Manager (QMan) fabric supporting packet-level queue management and
    quality of service scheduling
Three 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
    support
  Memory prefetch engine (PMan)
Data Path Acceleration Architecture (DPAA) incorporating acceleration for
    the following functions:
  Packet parsing, classification, and distribution (Frame Manager 1.1)
  Queue management for scheduling, packet sequencing, and congestion
    management (Queue Manager 1.1)
  Hardware buffer management for buffer allocation and de-allocation
    (BMan 1.1)
  Cryptography acceleration (SEC 5.0) at up to 40 Gbps
  RegEx Pattern Matching Acceleration (PME 2.1) at up to 10 Gbps
  Decompression/Compression Acceleration (DCE 1.0) at up to 20 Gbps
  DPAA chip-to-chip interconnect via RapidIO Message Manager (RMAN 1.0)
32 SerDes lanes at up to 10.3125 GHz
Ethernet interfaces
  Up to four 10 Gbps Ethernet MACs
  Up to sixteen 1 Gbps Ethernet MACs
  Maximum configuration of 4 x 10 GE + 8 x 1 GE
High-speed peripheral interfaces
  Four PCI Express 2.0/3.0 controllers
  Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz with
    Type 11 messaging and Type 9 data streaming support
  Interlaken look-aside interface for serial TCAM connection
Additional peripheral interfaces
  Two serial ATA (SATA 2.0) controllers
  Two high-speed USB 2.0 controllers with integrated PHY
  Enhanced secure digital host controller (SD/MMC/eMMC)
  Enhanced serial peripheral interface (eSPI)
  Four I2C controllers
  Four 2-pin or two 4-pin UARTs
  Integrated Flash controller supporting NAND and NOR flash
Two eight-channel DMA engines
Support for hardware virtualization and partitioning enforcement
QorIQ Platform's Trust Architecture 1.1
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Create new files to handle 2nd generation Chassis as the registers are
organized differently.

 - Add SerDes protocol parsing and detection
 - Add support of 4 SerDes
 - Add CPRI protocol in fsl_serdes.h
	The Common Public Radio Interface (CPRI) is publicly available
	specification that standardizes the protocol interface between the
	radio equipment control (REC) and the radio equipment (RE) in wireless
	basestations. This allows interoperability of equipment from different
	vendors,and preserves the software investment made by wireless service
	providers.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Add support for the Freescale P5040 SOC, which is similar to the P5020.
Features of the P5040 are:

Four P5040 single-threaded e5500 cores built
    Up to 2.4 GHz with 64-bit ISA support
    Three levels of instruction: user, supervisor, hypervisor
CoreNet platform cache (CPC)
    2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric
Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
        support Up to 1600MT/s
    Memory pre-fetch engine
DPAA incorporating acceleration for the following functions
    Packet parsing, classification, and distribution (FMAN)
    Queue management for scheduling, packet sequencing and
    congestion management (QMAN)
    Hardware buffer management for buffer allocation and
    de-allocation (BMAN)
    Cryptography acceleration (SEC 5.2) at up to 40 Gbps SerDes
    20 lanes at up to 5 Gbps
    Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces
    Two 10 Gbps Ethernet MACs
    Ten 1 Gbps Ethernet MACs
High-speed peripheral interfaces
    Two PCI Express 2.0/3.0 controllers
Additional peripheral interfaces
    Two serial ATA (SATA 2.0) controllers
    Two high-speed USB 2.0 controllers with integrated PHY
    Enhanced secure digital host controller (SD/MMC/eMMC)
    Enhanced serial peripheral interface (eSPI)
    Two I2C controllers
    Four UARTs
    Integrated flash controller supporting NAND and NOR flash
DMA
    Dual four channel
Support for hardware virtualization and partitioning enforcement
    Extra privileged level for hypervisor support
QorIQ Trust Architecture 1.1
    Secure boot, secure debug, tamper detection, volatile key storage
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Erratum: A-004034
Affects: SRIO

Description: During port initialization, the SRIO port performs
lane synchronization (detecting valid symbols on a lane) and
lane alignment (coordinating multiple lanes to receive valid data
across lanes). Internal errors in lane synchronization and lane
alignment may cause failure to achieve link initialization at
the configured port width.

An SRIO port configured as a 4x port may see one of these scenarios:

1.	One or more lanes fails to achieve lane synchronization.
	Depending on which lanes fail, this may result in downtraining
	from 4x to 1x on lane 0, 4x to 1x on lane R (redundant lane).

2.	The link may fail to achieve lane alignment as a 4x, even
	though all 4 lanes achieve lane synchronization, and downtrain
	to a 1x. An SRIO port configured as a 1x port may fail to complete
	port initialization (PnESCSR[PU] never deasserts) because of
	scenario 1.

Impact: SRIO port may downtrain to 1x, or may fail to complete
link initialization. Once a port completes link initialization
successfully, it will operate normally.
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the
workaround conditional.
In formal release document, the errata number should be ESDHC13 instead
of ESDHC136.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>