Add support for the Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC.

It was suggested to combine this functionality with the current ds2782
driver.  Unfortunately, I'm unable to commit the time to refactoring this
driver to that extent and I don't have a platform with the ds2782 part to
validate that there are no regression issues by adding this functionality.

[akpm@linux-foundation.org: use min_t()]
Signed-off-by: NClifton Barnes <cabarnes@indesign-llc.com>
Tested-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Avoid to get platform_data from parent device. Get it from mfd cell
device instead.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NAnton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Fix rated capacity of the HP iPAQ hx4700 3.7V 1800mAh (359113-001) battery. For this battery the value of the rated capacity EEPROM register at 0x32 is 7; thus rated_capacities[7] = 1800.
Signed-off-by: NPaul Parsons <lost.distance@yahoo.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Fix indexing of the 4 active full EEPROM registers. The indexing was out by 1, accessing the EEPROM registers at 0x23 to 0x26 instead of 0x22 to 0x25.
Signed-off-by: NPaul Parsons <lost.distance@yahoo.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

In 2008 Masashi YOKOTA <yokota@pylone.jp> created the virtual
battery driver found here:
http://downloads.pylone.jp/src/virtual_battery/virtual_battery-0.0.1.tar.bz2

It found use out of tree, but was never merged upstream.
Since then the test_power driver has been merged, which provides
very similar functionality.

This patch extends the test_power driver to be more dynamic
at runtime, by merging portions of the Virtual Battery Driver
by Masashi YOKOTA.

With this patch, I can tweak the values in:
/sys/module/test_power/parameters/* and watch the behavior of
the gnome power managment daemon or other battery UI software.

CC: Anton Vorontsov <cbouatmailru@gmail.com>
CC: Akihiro MAEDA <sola.1980.a@gmail.com>
CC: Masashi YOKOTA <yokota@pylone.jp>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

This patch fix using correct property POWER_SUPPLY_PROP_CYCLE_COUNT
for cycle count instead POWER_SUPPLY_PROP_CHARGE_COUNTER
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Tested-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

S390 is special as it doesn't have IRQ lines, so these errors pop up:

drivers/built-in.o: In function 'max8903_remove':
drivers/power/max8903_charger.c:355: undefined reference to 'free_irq'
drivers/power/max8903_charger.c:357: undefined reference to 'free_irq'
drivers/power/max8903_charger.c:359: undefined reference to 'free_irq'

This commit fixes the issue by making the driver depend on
GENERIC_HARDIRQS feature.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

The ISP1704/1707 chip can be put to full power down
state by asserting the CHIP_SEL line. This patch enables
platform or board specific hooks to put the device into
power down mode in case not needed.

This patch is a preparation for enabling this powering
routine in n900 (rx-51) devices.

Thanks to Heikki Krogerus for helping out with the patch.
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-By: NHeikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Gpio charger should notify if the gpio state had changed
during suspend. This will send a CHANGED event each time
the system resumes, ensuring a plug/unplug of the charger
is not missed.
Signed-off-by: NBenson Leung <bleung@chromium.org>
Acked-By: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

MAX8903 is an integrated battery charger and selector with two
power inputs (USB and AC adapter). This driver enables the charger,
handles interrupts, and provides power-supply-class information to
userland.

Tested on Exynos4 NURI / S5PC210 SLP7 boards.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Scripted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

mfd_get_cell returns a const, so change the jz4740 clients to store
a const mfd cell.  This silences type mismatch warnings.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

No need to explicitly set the cell's platform_data/data_size.

Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Corrected temperature and time to empty/full conversions.
Temperature is in 0.1°C, time is in seconds.

Corrected units in comment. "Convert to µWh."
Signed-off-by: NBenson Leung <bleung@chromium.org>
Acked-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

There are a few issues found around the battery not being present. If the
battery isn't present, then a few undesirable things happen. The first was
excessive reporting of failed properties. This was fixed by instead
returning ENODATA for all properties other than PRESENT if the battery
isn't present. That way the callers can identify the difference between a
failure and the battery not being there.

The next issue was in the suspend logic. It was found that if the battery
wasn't present, then it would return a failure, preventing the system from
going into suspend. If there is no battery present, the io is expected to
fail, so in that case, we shouldn't return the failure and just
acknowledge that it was expected.

I also found that when a gpio was used, i didn't maintain the internal
is_present state properly. I added a set of that to fix that.

Lastly, the code to see io's fail and figure out that the battery isn't
present when not using a gpio had a problem. In that code, it looked for
the read to fail and if it did, then handled it. The problem is that in
function to get the property, it first writes a value and that write can
fail, causing the code to never reach the logic after the read. Fix is
to move the logic till after the write.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

PROP_STATUS property was not counted, as result VOLTAGE_MIN property is
missing in sysfs. Fix it.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

s3c_adc_battery declares wrong method names when CONFIG_PM is not set.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entry will be added to
modules.alias:
alias i2c:aer915 z2_battery
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entries will be added to
modules.alias:
alias i2c:ds2786 ds2782_battery
alias i2c:ds2782 ds2782_battery
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entry will be added to
modules.alias:
alias i2c:bq20z75 bq20z75
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

With the support of platform data, now adding support for option i2c
retries on read/write failures. Ths is specified through the optional
platform data.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Adding support for an optional gpio for battery detection. This is
passed in through the i2c platform data. It also accepts another
field, battery_detect_present to signify the gpio state which means
the battery is present, either 0 (low) or 1 (high).
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

This queues work from the otg notification where the
i2c operations can be safely made. Needed for atomic otg
notifiers.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@nokia.com>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Doing this by using 2 calls sometimes results in unexpected
values being returned on OMAP3 i2c controller.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>

Some minor stylistic cleanups.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

* Consistently use uppercase for hexadecimal values.
* Clarify/fix the unit of functions return value in its comment.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

The current code only reports whether the battery is charging or
discharging. But the battery also reports whether it is fully charged,
furthermore by look at if the battery is supplied we can tell whether it
is discharging or not charging.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

This patch adds MODULE_DEVICE_TABLE for module bq27x00_battery.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Tested-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

This patch add support for reporting properties
POWER_SUPPLY_PROP_CHARGE_NOW, POWER_SUPPLY_PROP_CHARGE_FULL,
POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
POWER_SUPPLY_PROP_CHARGE_COUNTER, POWER_SUPPLY_PROP_ENERGY_NOW in
module bq27x00_battery.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

This patch adds support for polling the battery state and generating a
power_supply_changed() event if it has changed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

This patch adds a register cache to the bq27x00 battery driver.
Usually multiple, if not all, power_supply properties are queried at once,
for example when an uevent is generated. Since some registers are used by
multiple properties caching the registers should reduce the number of
reads.

The cache is valid for 5 seconds this roughly matches the internal update
interval of the current register for the bq27000/bq27200.

Fast changing properties(*_NOW) which can be obtained by reading a single
register are not cached.

It will also be used in the follow up patch to check if the battery status
has been changed since the last update to emit power_supply_changed events.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

This patch adds support for the bq27000 battery to the bq27x00 driver.
The bq27000 is similar to the bq27200 except that it uses the HDQ bus
instead of I2C to communicate with the host system.

The driver is implemented as a platform driver. The driver expects to be
provided with a read callback function through its platform data. The read
function is assumed to do the lowlevel HDQ handling and read out the value
of a certain register.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

This patch simplifies the drivers data structure and moves code to be
shared by the bq27000 and bq27200/bq27500 init functions into a common
function.
This patch has no functional changes, it only moves code around.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

This patch changes get_property callback of the bq27x00 battery to return
-ENODEV for properties other then the PROP_PRESENT if the battery is not
present.
The power subsystem core expects a driver to behave that way.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

According to the bq27000 datasheet the current should be calculated by
the following formula:
    current = AI * 3570 / 20

This patch adjust the drivers code accordingly.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

This patch improves the precession of the temperature property of the
bq27x00 driver.
By dividing before multiplying the current code effectively cuts of the
last decimal digit. This patch fixes it by multiplying before dividing.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

This patch adds the type property to the bq27x00 battery driver.
All bq27x00 are lithium ion batteries.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

Calling device_add causes an inital uevent for that device to be generated.
The power_supply uevent function calls the drivers get_property function,
which might causes the driver to update its state, which again might
causes the driver to call power_supply_changed(). Since the power_supplys
changed_work has not been initialized at this point the behavior is
undefined and can result in an OOPS.

This patch fixes the issue by initializing the power_supplys changed_work
prior to adding the power_supplys device to the device tree.
Reported-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>