* git://git.infradead.org/battery-2.6:
  PXA: Use dev_pm_ops in z2_battery
  ds2760_battery: Fix rated capacity of the hx4700 1800mAh battery
  ds2760_battery: Fix indexing of the 4 active full EEPROM registers
  power: Make test_power driver more dynamic.
  bq27x00_battery: Name of cycle count property
  max8903_charger: Add GENERIC_HARDIRQS as a dependency (fixes S390 build)
  ARM: RX-51: Enable isp1704 power on/off
  isp1704_charger: Allow board specific powering routine
  gpio-charger: Add gpio_charger_resume
  power_supply: Add driver for MAX8903 charger

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (coretemp) Fix section mismatch
  hwmon: (pmbus) Initialize sysfs attributes
  hwmon: (coretemp) Update comments describing the handling of HT CPUs
  hwmon: (coretemp) Initialize sysfs attributes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (26 commits)
  ASoC: Fix power down for widgetless per-card DAPM context case
  ASoC: wm1250-ev1: Define "WM1250 Output" with SND_SOC_DAPM_OUTPUT
  ASoC: Remove duplicate linux/delay.h inclusion.
  ASoC: sam9g20_wm8731: use the proper SYSCKL value
  ASoC: wm8731: fix wm8731_check_osc() connected condition
  ALSA: hda - Reorganize controller quriks with bit flags
  ALSA: hda - Use snd_printd() in snd_hda_parse_pin_def_config()
  ALSA: core: remove unused variables.
  ALSA: HDA: Increase MAX_HDMI_PINS
  ALSA: PCM - Don't check DMA time-out too shortly
  MAINTAINERS: add FireWire audio maintainer
  ALSA: usb-audio: more control quirks for M-Audio FastTrack devices
  ALSA: usb-audio: add new quirk type QUIRK_AUDIO_STANDARD_MIXER
  ALSA: usb-audio: export snd_usb_feature_unit_ctl
  ALSA: usb-audio: rework add_control_to_empty()
  ALSA: usb-audio: move assignment of chip->ctrl_intf
  ALSA: hda - Use model=auto for Lenovo G555
  ALSA: HDA: Unify HDMI hotplug handling.
  ALSA: hda - Force AD1988_6STACK_DIG for Asus M3N-HT Deluxe
  ASoC: core - remove superfluous new line.
  ...

chk_ucode_version() is only called from coretemp_probe() which is
__devinit, so it can be marked __devinit too.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Initialize sysfs attrs before device_create_file() call to suppress
lockdep_init_map() warning:

WARNING: at kernel/lockdep.c:2701 lockdep_init_map+0x12d/0x140()
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org # .39.x

Update comments describing the handling of HT CPUs based on review feedback.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

Initialize sysfs attrs before device_create_file() call to suppress lockdep_init_map()
warning:

[    3.653628] WARNING: at kernel/lockdep.c:2885 lockdep_init_map+0xea/0x43c()
[    3.653698] Modules linked in:
[    3.654835] Pid: 1, comm: swapper Not tainted 2.6.39-dbg-git8-05624-g46187f8 #576
[    3.656014] Call Trace:
[    3.657139]  [<ffffffff8103e4b4>] warn_slowpath_common+0x7e/0x96
[    3.658298]  [<ffffffff8103e4e1>] warn_slowpath_null+0x15/0x17
[    3.659460]  [<ffffffff8106d7b9>] lockdep_init_map+0xea/0x43c
[    3.660616]  [<ffffffff81163c1a>] sysfs_add_file_mode+0x5d/0xa8
[    3.661785]  [<ffffffff81163c71>] sysfs_add_file+0xc/0xe
[    3.662929]  [<ffffffff81163d26>] sysfs_create_file+0x23/0x25
[    3.664045]  [<ffffffff813724d1>] device_create_file+0x14/0x16
[    3.665172]  [<ffffffff81460ed4>] coretemp_probe+0xf9/0x185
[    3.666306]  [<ffffffff8137638e>] platform_drv_probe+0x12/0x14
[    3.667420]  [<ffffffff81375321>] driver_probe_device+0xb0/0x14b
[    3.668542]  [<ffffffff8137546d>] __device_attach+0x35/0x3a
[    3.669710]  [<ffffffff81375438>] ? __driver_attach+0x7c/0x7c
[    3.670816]  [<ffffffff8137426b>] bus_for_each_drv+0x54/0x88
[    3.671921]  [<ffffffff81375231>] device_attach+0x77/0x9b
[    3.673027]  [<ffffffff81374aef>] bus_probe_device+0x22/0x39
[    3.674137]  [<ffffffff81373235>] device_add+0x3c1/0x550
[    3.675249]  [<ffffffff81371ed9>] ? dev_set_name+0x3c/0x3e
[    3.676371]  [<ffffffff813769f3>] platform_device_add+0x10c/0x156
[    3.677491]  [<ffffffff8146af9c>] get_core_online+0xab/0x16e
[    3.678608]  [<ffffffff81ad8070>] coretemp_init+0x4b/0x80
[    3.679724]  [<ffffffff81ad8025>] ? hwmon_init+0xee/0xee
[    3.680853]  [<ffffffff8100020a>] do_one_initcall+0x7a/0x13c
[    3.681975]  [<ffffffff81aaac74>] kernel_init+0xe1/0x15b
[    3.683081]  [<ffffffff8147e4e4>] kernel_thread_helper+0x4/0x10
[    3.684174]  [<ffffffff8102d48c>] ? finish_task_switch+0x76/0xf0
[    3.685266]  [<ffffffff81477918>] ? retint_restore_args+0x13/0x13
[    3.686356]  [<ffffffff81aaab93>] ? start_kernel+0x3ee/0x3ee
[    3.687425]  [<ffffffff8147e4e0>] ? gs_change+0x13/0x13
[    3.688489] ---[ end trace 7392ad3e6a92ae39 ]---
Signed-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Merge branch 'upstream/tidy-xen-mmu-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen

* 'upstream/tidy-xen-mmu-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
  xen: fix compile without CONFIG_XEN_DEBUG_FS
  Use arbitrary_virt_to_machine() to deal with ioremapped pud updates.
  Use arbitrary_virt_to_machine() to deal with ioremapped pmd updates.
  xen/mmu: remove all ad-hoc stats stuff
  xen: use normal virt_to_machine for ptes
  xen: make a pile of mmu pvop functions static
  vmalloc: remove vmalloc_sync_all() from alloc_vm_area()
  xen: condense everything onto xen_set_pte
  xen: use mmu_update for xen_set_pte_at()
  xen: drop all the special iomap pte paths.

Right now security_get_user_sids() will pass in a NULL avd pointer to
avc_has_perm_noaudit(), which then forces that function to have a dummy
entry for that case and just generally test it.

Don't do it.  The normal callers all pass a real avd pointer, and this
helper function is incredibly hot.  So don't make avc_has_perm_noaudit()
do conditional stuff that isn't needed for the common case.

This also avoids some duplicated stack space.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linus:
  Squashfs: update email address
  Squashfs: add extra sanity checks at mount time
  Squashfs: add sanity checks to fragment reading at mount time
  Squashfs: add sanity checks to lookup table reading at mount time
  Squashfs: add sanity checks to id reading at mount time
  Squashfs: add sanity checks to xattr reading at mount time
  Squashfs: reverse order of filesystem table reading
  Squashfs: move table allocation into squashfs_read_table()

The implementation of find_next_bit_le() on m68knommu is identical with
the generic implementation of find_next_bit_le().
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The previous style change enables to use asm-generic/bitops/le.h on s390.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The previous style change enables to use asm-generic/bitops/le.h on arm.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

By the previous style change, CONFIG_GENERIC_FIND_NEXT_BIT,
CONFIG_GENERIC_FIND_BIT_LE, and CONFIG_GENERIC_FIND_LAST_BIT are not used
to test for existence of find bitops anymore.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The style that we normally use in asm-generic is to test the macro itself
for existence, so in asm-generic, do:

	#ifndef find_next_zero_bit_le
	extern unsigned long find_next_zero_bit_le(const void *addr,
		unsigned long size, unsigned long offset);
	#endif

and in the architectures, write

	static inline unsigned long find_next_zero_bit_le(const void *addr,
		unsigned long size, unsigned long offset)
	#define find_next_zero_bit_le find_next_zero_bit_le

This adds the #ifndef for each of the find bitops in the generic header
and source files.
Suggested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The style that we normally use in asm-generic is to test the macro itself
for existence, so in asm-generic, do:

	#ifndef find_next_zero_bit_le
	extern unsigned long find_next_zero_bit_le(const void *addr,
		unsigned long size, unsigned long offset);
	#endif

and in the architectures, write

	static inline unsigned long find_next_zero_bit_le(const void *addr,
		unsigned long size, unsigned long offset)
	#define find_next_zero_bit_le find_next_zero_bit_le

This adds the #define for each of the optimized find bitops in the
architectures.
Suggested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NHans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

m68knommu can't build ext4, udf, and ocfs2 due to the lack of
find_next_bit_le().

This implements find_next_bit_le() on m68knommu by duplicating the generic
find_next_bit_le() in lib/find_next_bit.c.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC.

It was suggested to combine this functionality with the current ds2782
driver.  Unfortunately, I'm unable to commit the time to refactoring this
driver to that extent and I don't have a platform with the ds2782 part to
validate that there are no regression issues by adding this functionality.

[akpm@linux-foundation.org: use min_t()]
Signed-off-by: NClifton Barnes <cabarnes@indesign-llc.com>
Tested-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reorganize so the netlink connector one wire search command will update
the kernel list of detected slave devices.  Otherwise, a newly detected
device is unusable because unless it's in the kernel list of known devices
any commands will result in ENODEV status.
Signed-off-by: NDavid Fries <David@Fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds multi-slave support of the w1 bus for the ds1wm Synthesizable
1-Wire Bus Master.  Also many fixes and tweaks based on the rev3 of the
datasheet http://datasheets.maxim-ic.com/en/ds/DS1WM.pdfSigned-off-by: NJean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This DS2408 w1 slave driver is not complete for all the features of the
chip, but its sufficient if you use it as a simple IO expander.

[randy.dunlap@oracle.com: fix w1_ds2408.c printk formats]
Signed-off-by: NJean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The first patch adds generic functionnality to w1_io for Resume Command
[A5h] lots of slaves support.  I found it useful for multi-commands/reset
workflows with the same slave on a multi-slave bus.

This DS2408 w1 slave driver is not complete for all the features of the
chip, but its sufficient if you use it as a simple IO expander.  Enjoy!

The ds1wm had Kconfig dependencies towards ARM && HAVE_CLK.  I took them
out since I was using the ds1wm on an x86_64 platform (ds1wm in a FPGA
through pcie) and found them irrelevant.

The clock freq/divisors at the top of ds1wm.c did not have the MSB set to
1.  This bit is CLK_EN which turns the whole prescaler and dividers on.
The driver never mentionned this bit either, so I just included this bit
right in the table entries.  I also took the liberty to add a couple of
entries to the table.  The spec doesn't explicitely mentions these
possibilities but the description and examination of the core shows the
prescalers & dividers can be used for more than the table explicitely
shows.  The table I enlarged still doesn't cover all possibilities, but
it's a good start.

I also made a few tweaks to a couple of the read and write algorithms
which made sense while I had my head very deep in the ds1wm documentation.
 We stressed it a lot with 10+ slaves on the bus, many ds2408, ds2431 and
ds2433 at the same time doing extensive interaction.  It proved quite
stable in our production environment.

This patch:

Add generic functionnality to w1_io for Resume Command [A5h] lots of
slaves support.
Signed-off-by: NJean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

profile_hits() has a common check for prof_on and prof_buffer regardless
of SMP or !SMP.  So, remove some duplicate code by splitting profile_hits
into two.

[akpm@linux-foundation.org: make do_profile_hits static]
Signed-off-by: NRakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

parport_find_number() calls parport_get_port() on its result, so there
should be a corresponding call to parport_put_port() before dropping the
reference.  Similar code is found in the function register_device() in the
same file.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

  // <smpl>
  @exists@
  local idexpression struct parport * x;
  expression ra,rr;
  statement S1,S2;
  @@

  x = parport_find_number(...)
  ... when != x = rr
      when any
      when != parport_put_port(x,...)
      when != if (...) { ... parport_put_port(x,...) ...}
  (
  if(<+...x...+>) S1 else S2
  |
  if(...) { ... when != x = ra
       when forall
       when != parport_put_port(x,...)
  *return...;
  }
  )
  // </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

synchronize_rcu() does the stuff as needed.
Signed-off-by: NLai Jiangshan <laijs@cn.fujitsu.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

finds is misspelt as finr. No functional change.
Signed-off-by: NSisir Koppaka <sisir.koppaka@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The kernel automatically evaluates partition tables of storage devices.
The code for evaluating GUID partitions (in fs/partitions/efi.c) contains
a bug that causes a kernel oops on certain corrupted GUID partition
tables.

This bug has security impacts, because it allows, for example, to
prepare a storage device that crashes a kernel subsystem upon connecting
the device (e.g., a "USB Stick of (Partial) Death").

	crc = efi_crc32((const unsigned char *) (*gpt), le32_to_cpu((*gpt)->header_size));

computes a CRC32 checksum over gpt covering (*gpt)->header_size bytes.
There is no validation of (*gpt)->header_size before the efi_crc32 call.

A corrupted partition table may have large values for (*gpt)->header_size.
 In this case, the CRC32 computation access memory beyond the memory
allocated for gpt, which may cause a kernel heap overflow.

Validate value of GUID partition table header size.

[akpm@linux-foundation.org: fix layout and indenting]
Signed-off-by: NTimo Warns <warns@pre-sense.de>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Eugene Teo <eugeneteo@kernel.sg>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Let memory allocator initialize the allocated memory as null, thus remove
the use of memset.
Signed-off-by: NRakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ->read_proc interface is going away, convert to seq_file.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc:Corey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The balloon driver in a Xen guest frees guest pages and marks them as
mmio.  When the kernel crashes and the crash kernel attempts to read the
oldmem via /proc/vmcore a read from ballooned pages will generate 100%
load in dom0 because Xen asks qemu-dm for the page content.  Since the
reads come in as 8byte requests each ballooned page is tried 512 times.

With this change a hook can be registered which checks wether the given
pfn is really ram.  The hook has to return a value > 0 for ram pages, a
value < 0 on error (because the hypercall is not known) and 0 for non-ram
pages.

This will reduce the time to read /proc/vmcore.  Without this change a
512M guest with 128M crashkernel region needs 200 seconds to read it, with
this change it takes just 2 seconds.
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently, pagemap_read() has three error and/or corner case handling
mistake.

 (1) If ppos parameter is wrong, mm refcount will be leak.
 (2) If count parameter is 0, mm refcount will be leak too.
 (3) If the current task is sleeping in kmalloc() and the system
     is out of memory and oom-killer kill the proc associated task,
     mm_refcount prevent the task free its memory. then system may
     hang up.

<Quote Hugh's explain why we shold call kmalloc() before get_mm()>

  check_mem_permission gets a reference to the mm.  If we
  __get_free_page after check_mem_permission, imagine what happens if the
  system is out of memory, and the mm we're looking at is selected for
  killing by the OOM killer: while we wait in __get_free_page for more
  memory, no memory is freed from the selected mm because it cannot reach
  exit_mmap while we hold that reference.

This patch fixes the above three.
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jovi Zhang <bookjovi@gmail.com>
Acked-by: NHugh Dickins <hughd@google.com>
Cc: Stephen Wilson <wilsons@start.ca>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It whould be better if put check_mem_permission after __get_free_page in
mem_write, to be same as function mem_read.

Hugh Dickins explained the reason.

    check_mem_permission gets a reference to the mm.  If we __get_free_page
    after check_mem_permission, imagine what happens if the system is out
    of memory, and the mm we're looking at is selected for killing by the
    OOM killer: while we wait in __get_free_page for more memory, no memory
    is freed from the selected mm because it cannot reach exit_mmap while
    we hold that reference.
Reported-by: NJovi Zhang <bookjovi@gmail.com>
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: NHugh Dickins <hughd@google.com>
Reviewed-by: NStephen Wilson <wilsons@start.ca>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is a macro for the max size kmalloc can allocate, so use it instead
of a hardcoded number.
Signed-off-by: NYuanhan Liu <yuanhan.liu@linux.intel.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No need for this local array to be writable, so mark it const.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert fs/proc/ from strict_strto*() to kstrto*() functions.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now, exe_file is not proc FS dependent, so we can use it to name core
file.  So we add %E pattern for core file name cration which extract path
from mm_struct->exe_file.  Then it converts slashes to exclamation marks
and pastes the result to the core file name itself.

This is useful for environments where binary names are longer than 16
character (the current->comm limitation).  Also where there are binaries
with same name but in a different path.  Further in case the binery itself
changes its current->comm after exec.

So by doing (s/$/#/ -- # is treated as git comment):

  $ sysctl kernel.core_pattern='core.%p.%e.%E'
  $ ln /bin/cat cat45678901234567890
  $ ./cat45678901234567890
  ^Z
  $ rm cat45678901234567890
  $ fg
  ^\Quit (core dumped)
  $ ls core*

we now get:

  core.2434.cat456789012345.!root!cat45678901234567890 (deleted)
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reviewed-by: NAndi Kleen <andi@firstfloor.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Setup and cleanup of mm_struct->exe_file is currently done in fs/proc/.
This was because exe_file was needed only for /proc/<pid>/exe.  Since we
will need the exe_file functionality also for core dumps (so core name can
contain full binary path), built this functionality always into the
kernel.

To achieve that move that out of proc FS to the kernel/ where in fact it
should belong.  By doing that we can make dup_mm_exe_file static.  Also we
can drop linux/proc_fs.h inclusion in fs/exec.c and kernel/fork.c.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Blackfin arch, like the x86 arch, needs to adjust the PC manually
after a breakpoint is hit as normally this is handled by the remote gdb.
However, rather than starting another arch ifdef mess, create a common
GDB_ADJUSTS_BREAK_OFFSET define for any arch to opt-in via their kgdb.h.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NDongdong Deng <dongdong.deng@windriver.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>