This is the first step to remove PLAT_PHYS_OFFSET usage from the debug
UART code.
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>

To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols.  This usually means that no global variables can
be marked static unless they're also const.

Let's remove the static qualifier from current offenders, or turn them
into const variables when possible.  Next commit will ensure the build
fails if one of those is reintroduced due to otherwise enforced coding
standards for the kernel.
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: NTony Lindgren <tony@atomide.com>

This patch adds initial support for the Hawkboard-L138 system
It is under the machine name "omapl138_hawkboard".
This system is based on the da850 davinci CPU architecture.
Information on these system may be found at http://www.hawkboard.org.
Basic support for the UART console is included in this patch.
It's tested with latest Angstrom File Systems like ramdisk
from http://alturl.com/imb45.
Signed-off-by: NVictor Rodriguez <victor.rodriguez@sasken.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system
on Module (SOM) under the machine name "mityomapl138".  These SOMs are based
on the da850 davinci CPU architecture.  Information on these SOMs may be
found at http://www.mitydsp.com.

Basic support for the console UART, NAND, and EMAC (MII interface) is
included in this patch.
Signed-off-by: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Added definitions for tnetv107x uart base addresses, and modified base address
selection for kernel decompressor to check for tnetv107x machine type.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adopts a debug uart selection similar to the OMAP model.  During
the boot process, the uncompress code determines the physical and virtual base
addresses of the board-specific debug uart.  These addresses are then passed
on to the in-kernel debug macros through a small chunk of memory placed just
below the page tables (@0x80003ff8).
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add support for the DA850/OMAP-L138 Evaluation Module (EVM)
from TI.  The EVM has User Interface (UI) card which contains
various devices. This UI card can be connected to the base
board. Support for all the devices on the UI card and ones on
the EVM will be added in subsequent patches.

The EVM schematics are not available publicly yet; but should
be available soon.

A new defconfig for this board has been added mainly because
the DA830/OMAP-L137 defconfig forces writethrough cache mode
which is not required on DA850/OMAP-L138.

This patch has been boot tested on DA850/OMAP-L138 EVM
using ramdisk as filesystem.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add support for the DA830/OMAP-L137 Evaluation Module (EVM)
from TI.  The EVM has User Interface (UI) and Audio cards
that can be connected which contain various devices.
Support for those devices and ones on the EVM will be
added in subsequent patches.

Additional generalizations for future SoCs in da8xx family done by
Sudhakar Rajashekhara and Sekhar Nori.
Signed-off-by: NSteve Chen <schen@mvista.com>
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The davinci pre-kernel boot code assumes that all platforms use the
same UART base address for the console.  That assumption is not longer
valid with some newer SoCs so determine the console UART base address
from the machine number passed in from bootloader.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add base kernel support for the TI DaVinci platform.

This patch only includes interrupts, timers, CPU identification,
serial support and basic power and sleep controller init.  More
drivers to come.
Signed-off-by: NKevin Hilman <khilman@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>