Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 4 年多

通知 15
Star 8
Fork 2
K
kernel_linux
切换分支/标签
  1. 04 11月, 2016 1 次提交
    • M
      MIPS: Fix FCSR Cause bit handling for correct SIGFPE issue · 5a1aca44
      由 Maciej W. Rozycki 提交于 
      Sanitize FCSR Cause bit handling, following a trail of past attempts:

* commit 42495484 ("MIPS: ptrace: Fix FP context restoration FCSR
regression"),

* commit 443c4403 ("MIPS: Always clear FCSR cause bits after
emulation"),

* commit 64bedffe ("MIPS: Clear [MSA]FPE CSR.Cause after
notify_die()"),

* commit b1442d39 ("MIPS: Prevent user from setting FCSR cause
bits"),

* commit b54d2901517d ("Properly handle branch delay slots in connection
with signals.").

Specifically do not mask these bits out in ptrace(2) processing and send
a SIGFPE signal instead whenever a matching pair of an FCSR Cause and
Enable bit is seen as execution of an affected context is about to
resume.  Only then clear Cause bits, and even then do not clear any bits
that are set but masked with the respective Enable bits.  Adjust Cause
bit clearing throughout code likewise, except within the FPU emulator
proper where they are set according to IEEE 754 exceptions raised as the
operation emulated executed.  Do so so that any IEEE 754 exceptions
subject to their default handling are recorded like with operations
executed by FPU hardware.
Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14460/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      5a1aca44
  3. 12 10月, 2016 3 次提交
  5. 10 10月, 2016 1 次提交
  7. 08 10月, 2016 3 次提交
  9. 07 10月, 2016 6 次提交
    • P
      MIPS: generic: Convert SEAD-3 to a generic board · 3f5f0a44
      由 Paul Burton 提交于 
      Convert the MIPS SEAD-3 board support to be a generic board, supported
by generic kernels.

Because the SEAD-3 boot protocol was defined long ago and we don't want
to force a switch to the UHI protocol, SEAD-3 is added as a legacy board
which is detected by reading the REVISION register. This may technically
not be a valid memory read & future work will include attempting to
handle that gracefully. In practice since SEAD-3 is the only legacy
board supported by the generic kernel so far the read will only happen
on SEAD-3 boards, and even once Malta is converted the same REVISION
register exists there too. Other boards such as Boston, Ci20 & Ci40 will
use the UHI boot protocol & thus not run any of the legacy board detect
functions.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14354/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      3f5f0a44
    • P
      MIPS: generic: Introduce generic DT-based board support · eed0eabd
      由 Paul Burton 提交于 
      Introduce a "generic" platform, which aims to be board-agnostic by
making use of device trees passed by the boot protocol defined in the
MIPS UHI (Universal Hosting Interface) specification. Provision is made
for supporting boards which use a legacy boot protocol that can't be
changed, but adding support for such boards or any others is left to
followon patches.

Right now the built kernels expect to be loaded to 0x80100000, ie. in
kseg0. This is fine for the vast majority of MIPS platforms, but
nevertheless it would be good to remove this limitation in the future by
mapping the kernel via the TLB such that it can be loaded anywhere & map
itself appropriately.

Configuration is handled by dynamically generating configs using
scripts/kconfig/merge_config.sh, somewhat similar to the way powerpc
makes use of it. This allows for variations upon the configuration, eg.
differing architecture revisions or subsets of driver support for
differing boards, to be handled without having a large number of
defconfig files.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14353/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      eed0eabd
    • P
      MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0 · 3ffc17d8
      由 Paul Burton 提交于 
      On MIPS64 we define the default CAC_BASE as one of the xkphys regions of
the virtual address space. Since the CCA is encoded in bits 61:59 of
xkphys addresses, fixing CAC_BASE to any particular one prevents us from
dynamically changing the CCA as we do for MIPS32 where CAC_BASE is
placed within kseg0. In order to make the kernel more generic, drop the
current kludge that gives CAC_BASE CCA=3 if CONFIG_DMA_NONCOHERENT is
selected (disregarding CONFIG_DMA_MAYBE_COHERENT) & CCA=5 (which is not
standardised by the architecture) otherwise. Instead read Config.K0 and
generate the appropriate offset into xkphys, presuming that either the
bootloader or early kernel code will have configured Config.K0
appropriately. This seems like the best option for a generic
implementation.

The ip27 spaces.h is adjusted to set its former value of CAC_BASE, since
it's the only user of CAC_BASE from assembly (in its smp_slave_setup
macro). This allows the generic case to focus solely on C code without
breaking ip27.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14351/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      3ffc17d8
    • P
      MIPS: Support per-device DMA coherence · 20d33064
      由 Paul Burton 提交于 
      On some MIPS systems, a subset of devices may have DMA coherent with CPU
caches. For example in systems including a MIPS I/O Coherence Unit
(IOCU), some devices may be connected to that IOCU whilst others are
not.

Prior to this patch, we have a plat_device_is_coherent() function but no
implementation which does anything besides return a global true or
false, optionally chosen at runtime. For devices such as those described
above this is insufficient.

Fix this by tracking DMA coherence on a per-device basis with a
dma_coherent field in struct dev_archdata. Setting this from
arch_setup_dma_ops() takes care of devices which set the dma-coherent
property via device tree, and any PCI devices beneath a bridge described
in DT, automatically.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14349/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      20d33064
    • P
      MIPS: Sanitise coherentio semantics · f2302023
      由 Paul Burton 提交于 
      The coherentio variable has previously been used as a boolean value,
indicating whether the user specified that coherent I/O should be
enabled or disabled. It failed to take into account the case where the
user does not specify any preference, in which case it makes sense that
we should default to coherent I/O if the hardware supports it
(hw_coherentio is non-zero).

Introduce an enum to clarify the 3 different values of coherentio & use
it throughout the code, modifying plat_device_is_coherent() &
r4k_cache_init() to take into account the default case.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/14347/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      f2302023
    • P
      MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY · c5611df9
      由 Paul Burton 提交于 
      Introduce 2 Kconfig symbols, CONFIG_PCI_DRIVERS_GENERIC &
CONFIG_PCI_DRIVERS_LEGACY, which indicate whether the system should be
built to for PCI drivers using the MIPS-specific struct pci_controller
API (hereafter "legacy" drivers) or more generic drivers using only
functionality provided by the PCI core (hereafter "generic" drivers).

The Kconfig entries are created such that platforms have to select
CONFIG_PCI_DRIVERS_GENERIC if they wish to use it - that is, the default
is CONFIG_PCI_DRIVERS_LEGACY so that existing platforms need no
modification.

The functions declared in pci.h are rearranged with those provided only
by pci-legacy.c being guarded by an #ifdef CONFIG_PCI_DRIVERS_LEGACY to
ensure they are only used in configurations where they are implemented.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14345/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      c5611df9
  11. 06 10月, 2016 6 次提交
  13. 05 10月, 2016 5 次提交
    • P
      MIPS: SEAD3: Probe EHCI controller using DT · 7afd2a5a
      由 Paul Burton 提交于 
      Probe the SEAD3 EHCI controller using the generic-ehci driver & device
tree rather than platform code, in order to reduce the amount of the
latter.

Now that no devices probed from platform code require interrupts, remove
the retrieval of the IRQ domain & sead3int.h.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14051/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      7afd2a5a
    • P
      MIPS: SEAD3: Probe ethernet controller using DT · a34e9388
      由 Paul Burton 提交于 
      Probe the smsc911x ethernet controller using device tree rather than
platform code, reducing the amount of the latter.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14050/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      a34e9388
    • P
      MIPS: SEAD3: Probe UARTs using DT · c11e3b48
      由 Paul Burton 提交于 
      Probe the UARTs on SEAD3 boards using device tree rather than platform
code, in order to reduce the amount of the latter. This requires that
CONFIG_SERIAL_OF_PLATFORM be enabled, so enable it in sead3_defconfig.
The SEAD3 DT shim code is extended to read bootloader environment
variables to determine the appropriate UART & mode for kernel console
output & set the stdout-path property of the chosen node accordingly.

In contrast to the old platform code, which appears to have only ever
set "console=ttyS0,38400n8r" with the code in console_config never
having an effect, this will honor the "yamontty" environment variable to
select between the 2 UARTs on the board and then check the "modetty0" or
"modetty1" variable as appropriate to determine the UART configuration.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14048/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      c11e3b48
    • P
      MIPS: SEAD3: Probe interrupt controllers using DT · b6d5e47e
      由 Paul Burton 提交于 
      Probe the CPU interrupt controller & optional Global Interrupt
Controller (GIC) using devicetree rather than platform code. Because the
bootloader on SEAD3 does not provide a device tree to the kernel & the
device tree is always built in, we patch out the GIC node during boot if
we detect that a GIC is not present in the system.

The appropriate IRQ domain is discovered by platform code setting up
device IRQ numbers temporarily. It will be removed by further patches
which move the devices towards being probed via device tree.

No behavioural change is intended by this patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14047/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      b6d5e47e
    • M
      MIPS: smp.c: Introduce mechanism for freeing and allocating IPIs · 7688c539
      由 Matt Redfearn 提交于 
      For the MIPS remote processor implementation, we need additional IPIs to
talk to the remote processor. Since MIPS GIC reserves exactly the right
number of IPI IRQs required by Linux for the number of VPs in the
system, this is not possible without releasing some recources.

This commit introduces mips_smp_ipi_allocate() which allocates IPIs to a
given cpumask. It is called as normal with the cpu_possible_mask at
bootup to initialise IPIs to all CPUs. mips_smp_ipi_free() may then be
used to free IPIs to a subset of those CPUs so that their hardware
resources can be reused.
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Lisa Parratt <Lisa.Parratt@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-remoteproc@vger.kernel.org
Cc: lisa.parratt@imgtec.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14285/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      7688c539
  15. 04 10月, 2016 11 次提交
  17. 02 10月, 2016 1 次提交
    • P
      MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems · 6605d156
      由 Paul Burton 提交于 
      When discovering the number of VPEs per core, smp_num_siblings will be
incorrect for kernels built without support for the MIPS MultiThreading
(MT) ASE running on systems which implement said ASE. This leads to
accesses to VPEs in secondary cores being performed incorrectly since
mips_cm_vp_id calculates the wrong ID to write to the local "other"
registers. Fix this by examining the number of VPEs in the core as
reported by the CM.

This patch presumes that the number of VPEs will be the same in each
core of the system. As this path only applies to systems with CM version
2.5 or lower, and this property is true of all such known systems, this
is likely to be fine but is described in a comment for good measure.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14338/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      6605d156
  19. 30 9月, 2016 2 次提交
  21. 29 9月, 2016 1 次提交
    • J
      KVM: MIPS: Invalidate TLB by regenerating ASIDs · 25b08c7f
      由 James Hogan 提交于 
      Invalidate host TLB mappings when the guest ASID is changed by
regenerating ASIDs, rather than flushing the entire host TLB except
entries in the guest KSeg0 range.

For the guest kernel mode ASID we regenerate on the spot when the guest
ASID is changed, as that will always take place while the guest is in
kernel mode.

However when the guest invalidates TLB entries the ASID will often by
changed temporarily as part of writing EntryHi without the guest
returning to user mode in between. We therefore regenerate the user mode
ASID lazily before entering the guest in user mode, if and only if the
guest ASID has actually changed since the last guest user mode entry.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
      25b08c7f