When we setup buffer for display plane, we'll check any pending
required GPU flush and possible make interruptible wait for flush
complete. But that wait would be most possibly to fail in case of
signals received for X process, which will then fail modeset process
and put display engine in unconsistent state. The result could be
blank screen or CPU hang, and DDX driver would always turn on outputs
DPMS after whatever modeset fails or not.

So this one creates new helper for setup display plane buffer, and
when needing flush using uninterruptible wait for that.

This one should fix bug like https://bugs.freedesktop.org/show_bug.cgi?id=24009.
Also fixing mode switch stress test on Ironlake.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

We restored RC6 twice on resume, even with modesetting off.  Instead,
only restore it once and skip RC6 initialization entirely in non-KMS mode.
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
Tested-by: NJeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This patch adds a new execbuf ioctl, execbuf2, for use by clients that
want to control fence register allocation more finely.  The buffer
passed in to the new ioctl includes a new relocation type to indicate
whether a given object needs a fence register assigned for the command
buffer in question.

Compatibility with the existing execbuf ioctl is implemented in terms
of the new code, preserving the assumption that fence registers are
required for pre-965 rendering commands.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[ickle: Remove pre-emptive clear_fence_reg()]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKristian Høgsberg <krh@bitplanet.net>
[anholt: Removed dmesg spam]
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NKristian Høgsberg <krh@bitplanet.net>
Signed-off-by: NEric Anholt <eric@anholt.net>

Instead of using the IS_I9XX etc macros that expand to a ton of
comparisons, use new struct intel_device_info to capture the
capabilities of the different chipsets.  The drm_i915_private struct
will be initialized to point to the device info that correspond to
the actual device and this way, testing for a specific capability is
just a matter of checking a bit field.
Signed-off-by: NKristian Høgsberg <krh@bitplanet.net>
Signed-off-by: NEric Anholt <eric@anholt.net>

Dirk reports that nothing is displayed on LVDS when using ubuntu 9.1 after
close/reopen the LID. And I also reproduce this issue on another laptop.
After some tests and debug, it seems that it is related with that the
LVDS status is not updated in time in course of suspend/resume.

Now the LID state is used to check whether the LVDS is connected or
disconnected. And when the LID is closed, it means that the LVDS is
disconnected. When it is reopened, it means that the LVDS is connected.
At the same time on some distributions the LID event is also used to put
the system into suspend state. When the LID is closed, the system will enter
the suspend state. When the LID is reopened, the system will be resumed.

In such case when the LID is closed, user-space script will receive the LID
notification event and  detect the LVDS as disconnected. Then the system will
enter the suspended state. When the LID is reopened, the system will be
resumed. As the LVDS status is not updated in course of resume, it will cause
that the LVDS connector is marked as unused and disabled. After the resume is
finished,user-space script will try to configure the display mode for LVDS.
But unfortunately as the LVDS status is not updated in time and it is still
marked as disconnected, the LVDS and its corresponding CRTC will be disabled
again in the function of drm_helper_disable_unused_functions after changing
mode for LVDS.

So we had better check and update the status of LVDS connector after receiving
the LID notication event. Then after the system is resumed from suspended
state, we can set the display mode for LVDS correctly.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Reported-by: NDirk Hohndel <hohndel@infradead.org>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
CC: stable@kernel.org
Signed-off-by: NEric Anholt <eric@anholt.net>

Rather than restoring just a few clock gating registers on resume,
just reinitialize the whole thing.
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
[anholt: Fixed up for RC6 support landed since the patch was written]
Signed-off-by: NEric Anholt <eric@anholt.net>

IGD* isn't a useful name.  Replace with the codenames, as sourced from
pci.ids.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
[anholt: Fixed up for merge with pineview/ironlake changes]
Signed-off-by: NEric Anholt <eric@anholt.net>

Acked-by: NJakob Bornecrantz <jakob@vmware.com>
Acked-by: NThomas Hellström <thomas@shipmail.org>
Review-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJesse "Orange Smoothie" Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NKristian Høgsberg <krh@bitplanet.net>
Signed-off-by: NEric Anholt <eric@anholt.net>

PineView only has 2 ports for LVDS and CRT. Don't enable other
ports for it.

Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

On some laptops there is no HDMI/DP. But the xrandr still reports
several disconnected HDMI/display ports. In such case the user will be
confused.
 >DVI1 disconnected (normal left inverted right x axis y axis)
 >DP1 disconnected (normal left inverted right x axis y axis)
 >DVI2 disconnected (normal left inverted right x axis y axis)
 >DP2 disconnected (normal left inverted right x axis y axis)
 >DP3 disconnected (normal left inverted right x axis y axis)

This patch set is to use the child device parsed in VBT to decide whether
the HDMI/DP/LVDS/TV should be initialized.

Parse the child device from VBT.

The device class type is also added for LFP, TV, HDMI, DP output.

https://bugs.freedesktop.org/show_bug.cgi?id=22785Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

if no VBT is present, crt_ddc_bus will be left at 0, and cause us
to use that for the GPIO register offset. That's never a valid register
offset, so let the "undefined" value be 0 instead of -1.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>
[anholt: clarified the commit message a bit]

If more than one mode with the same resolution defined in EDID has different
refresh rate, it is thought that the downclock is found for LVDS.
We will program the different FPx0/1 register so that we can select dynamically
between the low and high frequency.

On the g4x platform we will use the CxSR feature to switch the different
refresh rate if the LVDS downclock feature is supported.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Add more display registers save/restore to fix unstable issues
during S4 testing on Ironlake. And DPLL_B_MD should not be restored
on Ironlake.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Enable display hotplug irqs from Ibex Peak (PCH).
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Add the support of ACPI opregion on Ironlake so that the backlight
brightness can be adjusted by using ACPI interface
   >/sys/class/backlight/acpi_video0/brightness
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Tested-by: NZhao Yakui <yakui.zhao@intel.com>
[zhenyuw: cleanups, fix typo for checking GSE irq and convert to
current irq handling logic.]
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

It's not needed anymore.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

As long as the gpu can keep up, neither the cpu (waiting for gpu)
nore the gpu (waiting for vblank to do an overlay flip) stalls.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

This implements intel overlay support for kms via a device-specific
ioctl. Thomas Hellstrom brought up the idea of a general ioctl (on
dri-devel). We've reached the conclusion that such an infrastructure
only makes sense when multiple kms overlay implementations exists,
which atm don't (and it doesn't look like this is gonna change).

Open issues:
- Runs in sync with the gpu, i.e. unnecessary waiting. I've decided
  to wait on this because the hw tends to hang when changing something
  in this area. I left some dummy functions as infrastructure.
- polyphase filtering uses a static table.
- uses uninterruptible sleeps. Unfortunately the alternatives may
  unnecessarily wedged the hw if/when we timeout too early (and
  userspace only overloaded the batch buffers with stuff worth a few
  secs of gpu time).

Changes since v1:
- fix off-by-one misconception on my side. This fixes fullscreen
  playback.
Changes since v2:
- add underrun detection as spec'ed for i965.
- flush caches properly, fixing visual corruptions.
Changes since v4:
- fix up cache flushing of overlay memory regs.
- killed require_pipe_a logic - it hangs the chip.

Tested-By: diego.abelenda@gmail.com (on a 865G)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
[anholt: Resolved against the MADVISE ioctl going in before this one]
Signed-off-by: NEric Anholt <eric@anholt.net>

It is identical to I85X. Use that one instead.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
[anholt: fix conflicts against the display function pointer stuff]
Signed-off-by: NEric Anholt <eric@anholt.net>

This just waits until the hw passed the current ring position with
cmd execution. This slightly changes the existing i915_wait_request
function to make uninterruptible waiting possible - no point in
returning to userspace while mucking around with the overlay, that
piece of hw is just too fragile.

Also replace a magic 0 with the symbolic constant (and kill the then
superflous comment) while I was looking at the code.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

Render standy allows the GPU to power down the render unit when idle.
In order for this to work, it needs a page of graphics memory to save
state.  This patch allocates that page and enables the feature on
supported chipsets.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

In commit c1c7af60 ("drm/i915: force
mode set at lid open time") the intel graphics driver was taught to
restore the LVDS mode on lid open.

That caused problems with interaction with the suspend/resume code,
which commonly runs at the same time (suspend is often caused by the lid
close event, while lid open is commonly a resume event), which was
worked around with in commit 06891e27
("drm/i915: fix suspend/resume breakage in lid notifier").

However, in the meantime the lid event code had also grown a user event
notifier (commit 06324194: "drm/i915:
generate a KMS uevent at lid open/close time"), and now _that_ causes
problems with suspend/resume and some versions of Xorg reacting to those
uevents by setting the mode.

So this effectively reverts that commit 06324194, and makes the lid
open protection logic against suspend/resume more explicit.  This fixes
at least one laptop. See

	http://bugzilla.kernel.org/show_bug.cgi?id=14484

for more details.
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Cc: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds registers save/restore for Ironlake to make suspend work.
Signed-off-by: NGuo, Chaohong <chaohong.guo@intel.com>
[zhenyuw: some code re-orgnization, and add more save/restore for
FDI link and transcoder registers, also fix palette register for Ironlake]
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Turns out some machines, like the ThinkPad X40 don't come back if you
don't save/restore this register.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Until we figure out the right setting for powersave features on
Ironlake, disable it for now. Also disable watermark update,
which has new registers for it on Ironlake too.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Resolved against the Pineview FBC changes]
Signed-off-by: NEric Anholt <eric@anholt.net>

This hasn't fixed the regressions we were testing against, but clearly
should be required.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

According to the spec the LVDS_BORDER_ENABLE bit decides whether the border
data should be included in the active display and data sent to the panel.
Border should be used when in VGA centered (un-scaled) mode or when scaling
a 4:3 source image to a wide screen panel (typical 16:9).

So when the LVDS scaling is used, decide whether the LVDS_BORDER should be
enabled or not according to the current scaling mode.

At the same time fix the typo error in LVDS center scaling mode.

https://bugs.freedesktop.org/show_bug.cgi?id=23789Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
tested-by: NZhao Jian <jian.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Pineview doesn't have this FBC mechanism, so this code doesn't apply.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

If we trigger a tracepoint for batch buffer submission, it is a reasonable
assumption that we wish to also trace the batch buffer completion. So in
order to capture the completion events, we need to enable irqs... However,
we cannot rely on the completion event to disable the irq later, so we
defer the irq disable to the retire request.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Add support for framebuffer compression on GM45 and above.  Removes
some unnecessary I915_HAS_FBC checks as well (this is now part of the
FBC display function).
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

This patch splits out several of the display functions into a separate
display function table to avoid tons of chipset specific if..else
if..else if blocks all over.  There are more opportunities for this
(some noted in the structure defintition); so more cleanup patches will
follow.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

VGA arb requires DRM support for non-kms drivers, to turn on/off
irqs when disabling the mem/io regions.

VGA arb requires KMS support for GPUs where we can turn off VGA
decoding. Currently we know how to do this for intel and radeon
kms drivers, which allows them to be removed from the arbiter.

This patch comes from Fedora rawhide kernel.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Similar to the madvise() concept, the application may wish to mark some
data as volatile. That is in the event of memory pressure the kernel is
free to discard such buffers safe in the knowledge that the application
can recreate them on demand, and is simply using these as a cache.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This should help GEM handle memory pressure sitatuions more gracefully.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

There is no need to store the gtt_alignment as it is either explicitly
set according to the hardware requirements (e.g. scanout) or the
minimum alignment is computed on demand.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Due to a bogus FBC support check and failing to check for FBC support
in the right places, mode setting on non-mobile platforms could fail
and hang in the FBC disable routine.  Fix it up.

This fix highlights the need for cleanups in this area (function
pointers and better feature support checks).  Patches for that to
follow.
Tested-by: NKenny Graunke <kenny@whitecape.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We now unconditionally restore the mode at lid open time since some
platforms turn off the panel, pipes or other display elements when the
lid is closed.  There's a problem with doing this at resume time
however.

At resume time, we'll get a lid event, but restoring the mode at that
time may not be safe (e.g. if we get the lid event before global state
has been restored), so check the suspended state and make sure our
restore is locked against other mode updates.
Tested-by: NBen Gamari <bgamari.foss@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

There is a very real possibility that multiple CPUs will notice that the
GPU is wedged. This introduces all sorts of potential race conditions.
Make the wedged flag atomic to mitigate this risk.
Signed-off-by: NBen Gamari <bgamari.foss@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch puts in place the machinery to attempt to reset the GPU. This
will be used when attempting to recover from a GPU hang.
Signed-off-by: NOwain G. Ainsworth <oga@openbsd.org>
Signed-off-by: NBen Gamari <bgamari.foss@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>