This patch adds an idle hook imx_idle to be called in arch_idle().
Any soc that needs a customized idle implementation other than
cpu_do_idle() can set up this hook in soc specific call.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Currently each i.MX processor has its own function for displaying the silicon
revision.

Introduce a generic function for this purpose, so that all i.MX processors can
reuse it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NJason Liu <jason.hui@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

The patch removes all the uses of cpu_is_mx().  Instead, it utilizes
platform_device_id to distinguish the different gpio types, IMX1_GPIO
on i.mx1, IMX21_GPIO on i.mx21 and i.mx27, IMX31_GPIO on all other
i.mx SoCs.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.

 * Add a list to save all mx2 ports references, so that
   mx2_gpio_irq_handler can walk through all interrupt status
   registers

 * Use readl/writel to replace mach-specific accessors
   __raw_readl/__raw_writel

 * Change mxc_gpio_init into mxc_gpio_probe function

 * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
   be public at all, and also make some other cleanup on
   plat-mxc/include/mach/gpio.h at the same time

And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Since support for mxc91231 was introduced 2009 it only saw patches that
were part of (mxc or arm) global cleanups. The only supported machine
only had 4 devices (2x UART, sdhc, watchdog).

Cc: Dmitriy Taychenachev <dimichxp@gmail.com>
LAKML-Reference: 1302211482-17926-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Having the silicon revision to appear on the boot log is a useful information.

MX31, MX35 and MX51 already show the silicon revision on boot.

Add support for displaying such information for MX53 as well.

Tested on a mx53loco board, where it shows:

CPU identified as i.MX53, silicon rev 2.0
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1301068367-18937-1-git-send-email-fabio.estevam@freescale.com
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the memory
mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add core definitions and memory map, gpio, irq, iomux, uart device
support.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add iomux, clocks,  and memory map for Freescale's MX53 SoC.
Add cpu_is_mx53 function to common.h.
Add 3 more banks of gpio's to mxc_gpio_ports.
Add MX53 phys offset address.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The efikamx board is using a gpio to reset the board so add support
for it
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The Enhanced Periodic Interrupt Timer (EPIT) is found on newer
i.MX SoCs and can be used as an alternative system timer.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Add basic clock support, cpu identification, I/O mapping, interrupt
controller, serial port and ethernet.
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>

Freescale i.MX51 processor uses a new interrupt controller. Add
driver for TrustZone Interrupt Controller
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>

The fref is needless on mx25 since the reference clock is fixed at 24MHz.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NDmitriy Taychenachev <dimichxp@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This allows us to have more mapping functions for more than one
i.MX architecture in the kernel. As this is the earliest board
specific hook we have, also use it to set the cpu type.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds clock support for i.MX35 SoCs. We do not support setting
of clock rates yet, but most interesting clock rates should be reported.
I couldn't test all clock rates and the datasheet contains some obvious
bugs, so expect some bugs in this code.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

We had hardcoded cpu_is_ macros for mxc architectures till now. As we
want to run the same kernel on i.MX31 and i.MX35 this patch adds cpu_is_
macros which expand to 0 or 1 if only one architecture is compiled in and
only check for the cpu type if more than one architecture is compiled
in.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Based on code from "Martin Fuzzey" <mfuzzey@gmail.com>
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

- rename mxc_clocks_init to architecture specific versions. This
  allows us to have more than one architecture compiled in.
- call mxc_timer_init from clock initialisation instead from board
  code
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds timer support for the i.MX machine family. This code can
be used on the following machs:

 - i.MX1 (tested)
 - i.MX2 (i.MX21 (to be tested), i.MX27 (tested))
 - i.MX3 (i.MX31 (tested))

TODO: It seems impossible to build a kernel for more than one CPU because the
timer do not follow the platform device rules. So it does only work if
timer 1 can be accessed on all CPUs at the same address.
Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch bases on the one from Daniel Mack. The most important change to
Daniel's patch is to be more generic. This gpio routine supports at least
the i.MX27 and i.MX31 processors.
Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de>
Acked-by: NDaniel Mack <daniel@caiaq.de>

This patch introduces the clock API for for arch-mxc
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds the foundation pieces for
the Freescale MXC platforms, including
i.MX2 and i.MX3 based systems.

The bare-bones MX31 support in this patch
boots to the rootdev panic with 8250 serial
console configured "console=ttyS0,115200".
It assumes that Redboot is the boot loader.
Signed-off-by: NQuinn Jensen <quinn.jensen@freescale.com>
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>