Add clock, pin mux definitions and registration function for
VPIF capture and display driver on DA850/OMAP-L138 SoC.
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The wl1271 daughter board makes use of a few GPIOs:
GPIO6_9 is used for powering down/up the WLAN functionality.
GPIO6_10 is used as an input IRQ line from the WLAN chip.

Add the required pinmux configuration for these GPIOs.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

AM18x has two MMC slots. Add the required pinmux configuration for the
second slot.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

This patch defines Pin Mux configuration to enable MMC/SD
and USB-OHCI on the Hawkboard-L138 system
Signed-off-by: NVictor Rodriguez <vm.rod25@gmail.com>
Tested-by: NRene Gonzalez <renegs.2378@gmail.com>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

More complete AEMIF support for boards.
Signed-off-by: NThomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Added PINMUX configurations for the CLKOUT0 .. CLKOUT2
functions, for boards that want to use these clocks.
Signed-off-by: NThomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Board code may want to use them.
Signed-off-by: NThomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Pinmux registers are sequential, and do not need to be enumerated out as they
currently are.  This reduces code volume and keeps things simple.

If some future SoC comes up with a discontiguous register map, PINMUX() can
then be expanded with local token pasting.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Extended the MUX configuration to allow use of GPIO
terminals 64..57.
Signed-off-by: NThomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Added list of muxed pins on the tnetv107x SOC.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Rename da8xx_pinmux_setup() to davinci_cfg_reg_list() and promote it for use in
other SOCs that may need the ability to configure multiple pins in one shot.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds the generic Voice Codec support for the DM365 based
platforms.
Signed-off-by: NMiguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds support for registering for suspend-to-RAM
functionality on da850/omap-l138 SoCs.

da850 supports wakeup based on external event and RTC
alarm.

Currently only RTC alarm based wakeup is supported.
Support for wakeup based on external event will be
added as later improvements.

For scheduling an alarm event on RTC some useful code
is present in Documentation/rtc.txt
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The Neuros OSD 2.0 is the hardware component of the Neuros Open
Internet Television Platform. Hardware is very close to Ti DM644X-EVM board.
It has: DM6446M02 module with 256MB NAND, 256MB RAM, TLV320AIC32 AIC,
USB, Ethernet, SD/MMC, UART, THS8200, TVP7000 for video.
Additionaly realtime clock, IR remote control receiver,
IR Blaster based on MSP430 (firmware although is different
from used in DM644X-EVM), internal ATA-6 3.5” HDD drive
with PATA interface, two muxed red-green leds.

For more information please refer to
	http://wiki.neurostechnology.com/index.php/OSD_2.0_HDSigned-off-by: NAndrey Porodko <panda@chelcom.ru>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The general structures are defined at DM365 SoC file and the specific
platform data structure for the EVM is defined at board file.
Signed-off-by: NMiguel Aguilar <miguel.aguilar@ridgerun.com>

DA850/OMAP-L138 EVM has a RMII Ethernet PHY on the UI daughter card. The PHY
is enabled by proper programming of the IO Expander (TCA6416) ports. Also for
RMII PHY to work, the MDIO clock of MII PHY has to be disabled since both the
PHYs have the same address. This is done via the GPIO2[6] pin. This patch adds
support for RMII PHY.

This patch also adds a menuconfig option to select one or no peripheral
connected to expander. Currently, sub-options in this menu are RMII and no
peripheral.This menuconfig option is similar to the one present for UI card on
DA830/OMAP-L137 EVM.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

On the latest DA850/OMAP-L138 EVM (Beta) the GPIO pin
number of LCD panel power has changed. This patch takes
care of this change. Software will support only Beta
versions of DA850/OMAP-L138 EVM.

In the process, add the missing entry for data pin 0
and remove the GPIO specific pins from da850_lcdcntl_pins
structure. EVM specific muxing for LCD is being done in the
board file now.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

DM355 platform and board setup

This has platform and board setup changes to support vpfe capture
driver for DM355 EVMs.

Tested video capture on DM355 using tvp514x
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Reviewed-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NMuralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDenys Dmytriyenko <denis@denix.org>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds definitions for some DM365 IRQs that are used by
the codecs. Codecs will also use the IRQs.
Entries are being added to enable/disable IRQ's.
There is no use as such for these entires in the kernel itself.
Instead these will be used by the "linuxutils" package of the DVSDK.

For further information on IRQ muxing refer to
http://focus.ti.com/lit/ug/sprufg5a/sprufg5a.pdfSigned-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NSneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds PINMUX entries for DM355 Display.
These will be used by the DM355 display driver.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds platform data for the 8MB NOR flash
found on da850/omap-l138 EVM. Both NOR and NAND can
co-exist on da850/omap-l138 as they are using different
chip selects.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds platform data for the 512MB NAND Flash
found on DA850/OMAP-L138 EVM. Currently it supports
only 1-bit ECC.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

There are two instances of MMC/SD on da850/omap-l138.
Connector for the first instance is available on the
EVM. This patch adds support for this instance.

This patch also adds support for card detect and write
protect switches on da850/omap-l138 EVM.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds platform support for the graphic display
(Sharp LK043T1DG01) found on DA850/OMAP-L138 based EVM.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Define resources for McASP used on DA850/OMAP-L138 EVM, add platform
device defintion and Pin Mux configurations.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Earlier patch which adds EMAC support for da850/omap-l138
was not configuring the MDIO pins.

Ethernet was working fine with the earlier patch, because
the MDIO pins were configured from the boot loader. This
patch removes that dependency.

Also, this patch populates a member in the emac clk structure
to say that EMAC LPSC sits on controller 1.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The mask can hold only 8 bit values. This gave a
compilation warning. This patch rectifies the warning.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Ethernet Media Access Controller (EMAC) on da850/omap-l138
supports 10/100 Mbps operation. It also supports Media
Independent Interface (MII) and Reduced Media Independent
Interface (RMII) to physical layer (PHY).

Phy which supports MII is present on the DA850/OMAP-L138
base board and Phy supporting RMII is present on the
UI card. This patch adds support only for the MII Phy.
Support for RMII Phy will be added later.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The DA850/OMAP-L138 is a new SoC from TI in the same family as
DA830/OMAP-L137.

Major changes include better support for power management,
support for SATA devices and McBSP (same IP as DM644x).

DA850/OMAP-L138 documents are available at
http://focus.ti.com/docs/prod/folders/print/omap-l138.html.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Patch updates DM365 PINMUX by adding entries for Video, SPI 1 - 4,
PWM 0 - 3.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The da830/omap l137 is a new SoC from TI that is similar
to the davinci line.  Since its so similar to davinci,
put the support for the da830 in the same directory as
the davinci code.

There are differences, however.  Some of those differences
prevent support for davinci and da830 platforms to work
in the same kernel binary.  Those differences are:

1) Different physical address for RAM.  This is relevant
   to Makefile.boot addresses and PHYS_OFFSET.  The
   Makefile.boot issue isn't truly a kernel issue but
   it means u-boot won't work with a uImage including
   both architectures.  The PHYS_OFFSET issue is
   addressed by the "Allow for runtime-determined
   PHYS_OFFSET" patch by Lennert Buytenhek but it
   hasn't been accepted yet.

2) Different uart addresses.  This is only an issue
   for the 'addruart' assembly macro when CONFIG_DEBUG_LL
   is enabled.  Since the code in that macro is called
   so early (e.g., by _error_p in kernel/head.S when
   the processor lookup fails), we can't determine what
   platform the kernel is running on at runtime to use
   the correct uart address.

These areas have compile errors intentionally inserted
to indicate to the builder they're doing something wrong.

A new config variable, CONFIG_ARCH_DAVINCI_DMx, is added
to distinguish between a true davinci architecture and
the da830 architecture.

Note that the da830 currently has an issue with writeback
data cache so CONFIG_CPU_DCACHE_WRITETHROUGH should be
enabled when building a da830 kernel.

Additional generalizations for future SoCs in the da8xx family done by
Sudhakar Rajashekhara and Sekhar Nori.
Signed-off-by: NSteve Chen <schen@mvista.com>
Signed-off-by: NMikhail Cherkashin <mcherkashin@ru.mvista.com>
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The patch adds base support for new TI SOC DM365, which s
similar to the dm355.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Different SoC have different numbers of pinmux registers and other
resources that overlap with each other.  To clean up the code and
eliminate defines that overlap with each other, move the PINMUX
defines to the SoC specific files.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The pinmux register base and setup can be different for different
SoCs so move the pinmux reg base, pinmux table (and its size) to
the SoC infrastructure.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Update MUX support to be more general and useful across multiple
SoCs in the DaVinci family.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support pin multiplexing configurations driver for TI DaVinci SoC
Signed-off-by: NVladimir Barinov <vbarinov@ru.mvista.com>
Acked-by: NKevin Hilman <khilman@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>