Add basic support for the CPLD on the DM365 EVM board:

 - Read SW5 to set up NAND and keypad vs (someday) OneNAND
 - Export MMC/SD card detect and writeprotect signals
 - LED support (same layout as on DM355 EVM)
 - Static config for video input:
     * external HD imager precludes MMC1, Ethernet, audio
     * else either tvp5146 (SD/default) or tvp7002 (HD)

The video input could actually be switched around dynamically;
change that if/when that's needed (and after those other video
inputs have driver support).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Patch adds support for MMC/SD in the DM365 EVM.
Pinmux for MMC/SD slot 1 on the DM365 EVM is also
configured.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The patch adds Support for EMAC in the DM365 SOC and
the DM365 EVM board.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch does the following
1) Adds entries to davinci_all_defconfig for DM365
2) Adds entries to the Makefile for DM365
3) Adds entries for DM365 in the Kconfig
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The patch adds support for Evaluation Module (EVM) board for the dm365
SoC.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The patch adds base support for new TI SOC DM365, which s
similar to the dm355.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

watchdog info is not needed in soc_info, platform_device can
be used directly in core code.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

CC      arch/arm/mach-davinci/sram.o
arch/arm/mach-davinci/sram.c: In function 'sram_init':
arch/arm/mach-davinci/sram.c:63: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

JTAG ID for DM644x silicon revision 2.1 has changed. An entry for the new
silicon revision needs to be added to the davinci_id structure. Without
this addition, EVMs with new silicon revision fail to boot the kernel.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The davinci reset routine, davinci_watchdog_reset(), sets the
TCR register instead of the TGCR register as it should to put
the WDT into its "Initial State".

It also writes the WDTCR register without the proper WDKEY
which is pointless since the register will be write-protected.
Signed-off-by: NDavid Griego <dgriego@mvista.com>
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Adds McASP clock support for the two instances of mcasp (mcasp0,mcasp1). This
patch is part of the audio support for dm646x series.
Signed-off-by: NNaresh Medisetty <naresh@ti.com>
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Enables module clock for DM646x EDMA channel controller and transfer
controller.
Signed-off-by: NNaresh Medisetty <naresh@ti.com>
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

- restructure to support multiple channel controllers by using
  additional struct resources for each CC

- interface changes visible to EDMA clients

  Introduce macros to build IDs from controller and channel number,
  and to extract them. Modify the edma_alloc_slot function to take an
  extra argument for the controller.

  Also update ASoC drivers to use API.  ASoC changes
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

- Move queue related mappings to dm<soc>.c

  EDMA in DM355 and DM644x has two transfer controllers while DM646x
  has four transfer controllers. Moving the queue to tc mapping and
  queue priority mapping to dm<soc>.c will be helpful to probe these
  mappings from platform device so that the machine_is_* testing will
  be avoided.

- add channel mapping logic

  Channel mapping logic is introduced in dm646x EDMA. This implies
  that there is no fixed association for a channel number to a
  parameter entry number. In other words, using the DMA channel
  mapping registers (DCHMAPn), a PaRAM entry can be mapped to any
  channel. While in the case of dm644x and dm355 there is a fixed
  mapping between the EDMA channel and Param entry number.
Signed-off-by: NNaresh Medisetty <naresh@ti.com>
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Reviewed-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

fix the following 'make includecheck' warning:

  arch/arm/mach-davinci/board-sffsdr.c: mach/common.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NPhilip Balister <philip@opensdr.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

fix the following 'make includecheck' warning:

  arch/arm/mach-davinci/board-dm646x-evm.c: mach/common.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

fix the following 'make includecheck' warning:

  arch/arm/mach-davinci/board-dm644x-evm.c: mach/common.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

fix the following 'make includecheck' warning:

  arch/arm/mach-davinci/board-dm355-leopard.c: mach/common.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

fix the following 'make includecheck' warning:

  arch/arm/mach-davinci/board-dm355-evm.c: mach/common.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Minimal support for the 4-bit ECC engine found on DM355, DM365,
DA830/OMAP-L137, and similar recent DaVinci-family chips.

This is limited to small-page flash for now; there are some page
layout issues for large page chips.  Note that most boards using
this engine (like the DM355 EVM) include 2GiB large page chips.

Sanity tested on DM355 EVM after swapping the socketed NAND for
a small-page one.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Kconfig entries default to n, so there's no need for this to be
explicitly specified.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Some DMA_32BIT_MASK usage snuck in with the MMC platform support.
Convert these to the new preferred DMA_BIT_MASK(32).
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Provide a generic SRAM allocator using genalloc, and vaguely
modeled after what AVR32 uses.  This builds on top of the
static CPU mapping set up in the previous patch, and returns
DMA mappings as requested (if possible).

Compared to its OMAP cousin, there's no current support for
(currently non-existent) DaVinci power management code running
in SRAM; and this has ways to deallocate, instead of being
allocate-only.

The initial user of this should probably be the audio code,
because EDMA from DDR is subject to various dropouts on at
least DM355 and DM6446 chips.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Package on-chip SRAM.  It's always accessible from the ARM, so
set up a standardized virtual address mapping into a 128 KiB
area that's reserved for platform use.

In some cases (dm6467) the physical addresses used for EDMA are
not the same as the ones used by the ARM ... so record that info
separately in the SOC data, for chips (unlike the OMAP-L137)
where SRAM may be used with EDMA.

Other blocks of SRAM, such as the ETB buffer or DSP L1/L2 RAM,
may be unused/available on some system.  They are ignored here.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Remove remnants of dm6446-specific SRAM allocator, as preparation for
a more generic replacement.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Different SoC have different numbers of pinmux registers and other
resources that overlap with each other.  To clean up the code and
eliminate defines that overlap with each other, move the PINMUX
defines to the SoC specific files.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The Timer64p timer has 8 compare registers that can
be used to generate interrupts when the timer value
matches the compare reg's value.  They do not disturb
the timer itself.  This can be useful when there is
only one timer available for both clock events and
clocksource.

When enabled, the clocksource remains a continuous
32-bit counter but the clock event will no longer
support periodic interrupts.  Instead only oneshot
timers will be supported and implemented by setting
the compare register to the current timer value plus
the period that the clock event subsystem is requesting.

Compare registers support is enabled automatically
when the following conditions are met:
1) The same timer is being used for clock events
   and clocksource.
2) The timer is the bottom half (32 bits) of the
   64-bit timer (hardware limitation).
3) The the compare register offset and irq are
   not zero.

Since the timer is always running, there is a hardware
race in timer32_config() between reading the current
timer value, and adding the period to the current
timer value and writing the compare register.
Testing on a da830 evm board with the timer clocked
at 24 MHz and the processor clocked at 300 MHz,
showed the number of counter ticks to do this ranged
from 20-53 (~1-2.2 usecs) but usually around 41 ticks.
This includes some artifacts from collecting the
information.  So, the minimum period should be
at least 5 usecs to be safe.

There is also an non-critical lower limit that
the period should be since there is no point in
setting an event that is much shorter than the
time it takes to set the event, and get & handle
the timer interrupt for that event.  There can
also be all sorts of delays from activities
occuring elsewhere in the system (including
hardware activitis like cache & TLB management).
These are virtually impossible to quantify so a
minimum period of 50 usecs was chosen.  That will
certianly be enough to avoid the actual hardware
race but hopefully not large enough to cause
unreasonably course-grained timers.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Integrate the Common Platform Interrupt Controller (cp_intc)
support into the low-level irq handling for davinci and similar
platforms.  Do it such that support for cp_intc and the original
aintc can coexist in the same kernel binary.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Factor out the code to extract that mac address from
i2c eeprom.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The dm644x and dm646x board files have i2c eeprom read and
write routines but they are not used so remove them.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Since most of the emac platform_data is really SoC specific
and not board specific, move it to the SoC-specific files.
Put a pointer to the platform_data in the soc_info structure
so the board-specific code can set some of the platform_data
if it needs to.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Currently, there is one set of platform_device and platform_data
structures for all DaVinci SoCs.  The differences in the data
between the various SoCs is handled by davinci_serial_init()
by checking the SoC type.  However, as new SoCs appear, this
routine will become more & more cluttered.

To clean up the routine and make it easier to add support for new
SoCs, move the platform_device and platform_data structures into the
SoC-specific code and use the SoC infrastructure to provide access
to the data.

In the process, fix a bug where the wrong irq is used for uart2
of the dm646x.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The current gpio code needs to know the number of
gpio irqs there are and what the bank irq number is.
To determine those values, it checks the SoC type.

It also assumes that the base address and the number
of irqs the interrupt controller uses is fixed.

To clean up the SoC checks and make it support
different base addresses and interrupt controllers,
have the SoC-specific code set those values in
the soc_info structure and have the gpio code
reference them there.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The watchdog code currently hardcodes the base address
of the timer its using.  To support new SoCs, make it
support timers at any address.  Use the soc_info structure
to do this.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The davinci timer code currently hardcodes the timer register
base addresses, the timer irq numbers, and the timers to use
for clock events and clocksource.  This won't work for some
a new SoC so put those values into the soc_info structure
and set them up in the SoC-specific files.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>