Add DMA mode support for the MMCIF controller on mackerel.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Remember to also check for the CONFIG_MMC_SH_MMCIF_MODULE option
for the case of a modular MMCIF driver.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

If several boards are enabled in the kernel configuration,
hdmi_init_pm_clock() functions from board-ap4evb.c and board-mackerel.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <damm@opensource.se>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert to the new function names. Automated with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

SDHI registers occupy only a 0x100 byte large window, not 0x200 byte.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Cameras are currently broken on ARM sh-mobile platforms. They need a
suitable coherent DMA mask.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use GPIO_PORT31 to control the backlight on the Mackerel board.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

mackerel WVGA LCDC panel expect 33.3MHz for dot-clock,
but current dot-clock was 50.0MHz.
This patch modify clock divider value.
Signed-off-by: NMakoto Ueda <makoto.ueda.ub@renesas.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Current format selection of FSI-codecs depended on platform information for FSI,
and chip default settings for codecs. It is not understandable/formal method.
This patch modify FSI and FSI-codecs to use snd_soc_dai_set_fmt.

But FSI can use I2S/PCM and SPDIF format today.
It can be selected to I2S/PCM by snd_soc_dai_set_fmt, but can not select SPDIF.
So, this patch change FSI platform information to have DAI/SPDIF mode.

If platform selects DAI mode (default),
FSI-codecs can select I2S/PCM by snd_soc_dai_set_fmt,
and if it is SPDIF mode, FSI become SPDIF format.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch add platform_device_id which can control
PortA/PortB for FSI2-HDMI from platform data.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch add snd_soc_dai_ops :: set_fmt to FSI driver and
select master/slave clock mode by snd_soc_dai_set_fmt on
fsi-xxx.c instead of platform infomation code.
This patch remove fsi_is_master function which is no longer needed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

* Pins 2 and 4 of switch 33 are documented as don't care on the PCB,
  my testing seems to confirm this.

* I have been unable to do anything sensible with S1 set to on.
  Am I missing something with regards to MMC1?

* Clarify which driver is needed for each switch setting.

* Should the AP4 board code be updated to allow the
  SHDI driver to access SHDI1 as the mackerel code does?
Signed-off-by: NSimon Horman <horms@verge.net.au>
Acked-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The Card Detect GPIOs used on AP4EVB and Mackerel are
alwayws valid, so kill off the unused !gpio_is_valid()
case.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Enable SDIO IRQ support for the Mackerel board.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NTony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Break-out INTC specific IRQ demux code from the file
entry-macro-intc.S and register during run-time.

Covers sh7367, sh7377 and sh7372.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add VGA camera support to the Mackerel board
using soc_camera_platform.

The VGA camera module is hooked up using the
8-bit CEU bus, and it is constantly bursting
out frames in fixed video mode setting. The
camera module does not allow any I2C control.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

v2
 Add comment of J22 and OCR field.
Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch maps key0/key1/key2/key3 as HOME/MENU/BACK/POWER buttons
on mackerel board.
Signed-off-by: NTony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NTony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

you can control it by
echo 0 > /sys/class/leds/led0/brightness
echo 1 > /sys/class/leds/led0/brightness
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

RGB24 bus needs 18-23 pin
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>