Remove a few extra lines and make it clear that all implementations
disable the port by sharing the same line of code.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Some usb3 devices falsely claim they support usb2 hardware Link PM
when connected to a usb2 port. We only trust hardwired devices
or devices with the later BESL LPM support to be LPM enabled as default.

[Note: Sarah re-worked the original patch to move the code into the USB
core, and updated it to check whether the USB device supports BESL,
instead of checking if the xHCI port it's connected to supports BESL
encoding.]

This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdc "usb: xhci:
add USB2 Link power management BESL support".  Without this fix, some
USB 3.0 devices will not enumerate or work properly under USB 2.0 ports
on Haswell-ULT systems.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

How it's supposed to work:
--------------------------

USB 2.0 Link PM is a lower power state that some newer USB 2.0 devices
support.  USB 3.0 devices certified by the USB-IF are required to
support it if they are plugged into a USB 2.0 only port, or a USB 2.0
cable is used.  USB 2.0 Link PM requires both a USB device and a host
controller that supports USB 2.0 hardware-enabled LPM.

USB 2.0 Link PM is designed to be enabled once by software, and the host
hardware handles transitions to the L1 state automatically.  The premise
of USB 2.0 Link PM is to be able to put the device into a lower power
link state when the bus is idle or the device NAKs USB IN transfers for
a specified amount of time.

...but hardware is broken:
--------------------------

It turns out many USB 3.0 devices claim to support USB 2.0 Link PM (by
setting the LPM bit in their USB 2.0 BOS descriptor), but they don't
actually implement it correctly.  This manifests as the USB device
refusing to respond to transfers when it is plugged into a USB 2.0 only
port under the Haswell-ULT/Lynx Point LP xHCI host.

These devices pass the xHCI driver's simple test to enable USB 2.0 Link
PM, wait for the port to enter L1, and then bring it back into L0.  They
only start to break when L1 entry is interleaved with transfers.

Some devices then fail to respond to the next control transfer (usually
a Set Configuration).  This results in devices never enumerating.

Other mass storage devices (such as a later model Western Digital My
Passport USB 3.0 hard drive) respond fine to going into L1 between
control transfers.  They ACK the entry, come out of L1 when the host
needs to send a control transfer, and respond properly to those control
transfers.  However, when the first READ10 SCSI command is sent, the
device NAKs the data phase while it's reading from the spinning disk.
Eventually, the host requests to put the link into L1, and the device
ACKs that request.  Then it never responds to the data phase of the
READ10 command.  This results in not being able to read from the drive.

Some mass storage devices (like the Corsair Survivor USB 3.0 flash
drive) are well behaved.  They ACK the entry into L1 during control
transfers, and when SCSI commands start coming in, they NAK the requests
to go into L1, because they need to be at full power.

Not all USB 3.0 devices advertise USB 2.0 link PM support.  My Point
Grey USB 3.0 webcam advertises itself as a USB 2.1 device, but doesn't
have a USB 2.0 BOS descriptor, so we don't enable USB 2.0 Link PM.  I
suspect that means the device isn't certified.

What do we do about it?
-----------------------

There's really no good way for the kernel to test these devices.
Therefore, the kernel needs to disable USB 2.0 Link PM by default, and
distros will have to enable it by writing 1 to the sysfs file
/sys/bus/usb/devices/../power/usb2_hardware_lpm.  Rip out the xHCI Link
PM test, since it's not sufficient to detect these buggy devices, and
don't automatically enable LPM after the device is addressed.

This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdc "usb: xhci:
add USB2 Link power management BESL support".  Without this fix, some
USB 3.0 devices will not enumerate or work properly under USB 2.0 ports
on Haswell-ULT systems.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Before the USB core resets a device, we need to disable the L1 timeout
for the roothub, if USB 2.0 Link PM is enabled.  Otherwise the port may
transition into L1 in between descriptor fetches, before we know if the
USB device descriptors changed.  LPM will be re-enabled after the
full device descriptors are fetched, and we can confirm the device still
supports USB 2.0 LPM after the reset.

We don't need to wait for the USB device to exit L1 before resetting the
device, since the xHCI roothub port diagrams show a transition to the
Reset state from any of the Ux states (see Figure 34 in the 2012-08-14
xHCI specification update).

This patch should be backported to kernels as old as 3.2, that contain
the commit 65580b43 "xHCI: set USB2
hardware LPM".  That was the first commit to enable USB 2.0
hardware-driven Link Power Management.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Signed-off-by: NMatthias Beyer <mail@beyermatthias.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

including:

- removing of trailing whitespace
- removing spaces before array indexing (foo [] to foo[])
- reindention of a switch-case block
- spaces to tabs
Signed-off-by: NMatthias Beyer <mail@beyermatthias.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These aren't necessary after switch and if blocks.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_disconnect() no longer acquires usb_bus_list_lock, so update its
comment to that effect.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Set SEL control urbs cannot be sent to a device in unconfigured state.
This patch adds a check in usb_req_set_sel() to ensure the usb device's
state is USB_STATE_CONFIGURED.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: NMartin MOKREJS <mmokrejs@gmail.com>
Suggested-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

In the bos usb_ss_cap_descriptor structure, bU2DevExitLat is of type __le16.
This value is used as it is, without being first converted to the CPU
byteorder, for the setup of usb device's usb3_lpm_parameters.
This patch fixes that by converting bU2DevExitLat field to the CPU byteorder
before the assignmenment to [udev/hub]_u2_del variables.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch sets the lpm_capable field for root hubs with LPM capabilities.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: NMartin MOKREJS <mmokrejs@gmail.com>
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the incorrect assignment of a variable with type 'le16'
to a variable with type 'unsigned int'.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In usb_reset_and_verify_device(), hub_port_init() allocates a new bos
descriptor to hold the value read by the device. The new bos descriptor
has to be compared with the old one in order to figure out if device 's
firmware has changed in which case the device has to be reenumerated.
In the original code, none of the two descriptors was deallocated leading
to memory leaks.

This patch compares the old bos descriptor with the new one to detect change
in firmware and releases the newly allocated bos descriptor to prevent memory
leak.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: NMartin MOKREJS <mmokrejs@gmail.com>
Tested-by: NMartin MOKREJS <mmokrejs@gmail.com>
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

After successful initialization hub->descriptor->bNbrPorts and
hub->hdev->maxchild are equal, but using hub->hdev->maxchild is
preferred because that value is explicitly used for initialization
of hub->ports[].
Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Ignoring usb_hub_create_port_device() errors cause later NULL pointer
deference when uninitialized hub->ports[i] entries are dereferenced
after port memory allocation error.
Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the hub_configure() fails after setting the hdev->maxchild
the hub->ports might be NULL or point to uninitialized kzallocated
memory causing NULL pointer dereference in hub_quiesce() during cleanup.

Now after such error the hdev->maxchild is set to 0 to avoid cleanup
of uninitialized ports.
Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The pm qos NO_POWER_OFF flag is checked twice during usb device suspend
to see if the usb port power off condition is met. This is redundant and
also will prevent the port from being powered off if the NO_POWER_OFF
flag is changed to 1 from 0 after the device was already suspended.

More detail in the following link.
	http://marc.info/?l=linux-usb&m=136543949130865&w=2

This patch should be backported to kernels as old as 3.7, that
contain the commit f7ac7787 "usb/acpi:
Use ACPI methods to power off ports."
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

The hub driver's usb_port_suspend() routine doesn't handle errors
related to Link Power Management properly.  It always returns failure,
it doesn't try to clean up the wakeup setting, (in the case of system
sleep) it doesn't try to go ahead with the port suspend regardless,
and it doesn't try to apply the new power-off mechanism.

This patch fixes these problems.

Note: Sarah fixed this patch to apply against 3.11, since the original
commit (4fae6f0f "USB: handle LPM errors
during device suspend correctly") called usb_disable_remote_wakeup,
which won't be added until 3.12.

This patch should be backported to kernels as old as 3.5, that
contain the commit 8306095f "USB:
Disable USB 3.0 LPM in critical sections.".  There will be merge
conflicts, since LTM wasn't added until 3.6.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

When building the htmldocs (in verbose mode), scripts/kernel-doc reports the
following type of warnings:

Warning(drivers/usb/core/usb.c:76): No description found for return value of
'usb_find_alt_setting'

Fix them by:
- adding some missing descriptions of return values
- using "Return" sections for those descriptions
Signed-off-by: NYacine Belkadi <yacine.belkadi.1@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The hub driver's usb_port_suspend() routine doesn't handle errors
related to Link Power Management properly.  It always returns failure,
it doesn't try to clean up the wakeup setting, (in the case of system
sleep) it doesn't try to go ahead with the port suspend regardless,
and it doesn't try to apply the new power-off mechanism.

This patch fixes these problems.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The hub driver is inconsistent in its organization of code for
enabling and disabling remote wakeup.  There is a special routine to
disable wakeup for SuperSpeed devices but not for slower devices, and
there is no special routine to enable wakeup.

This patch refactors the code.  It renames and changes the existing
function to make it handle both SuperSpeed and non-SuperSpeed devices,
and it adds a corresponding routine to enable remote wakeup.  It also
changes the speed determination to look at the device's speed rather
than the speed of the parent hub -- this shouldn't make any difference
because a SuperSpeed device always has to be attached to a SuperSpeed
hub and conversely.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch simplifies the interface presented by usb_get_status().
Instead of forcing callers to check for the proper data length and
convert the status value to host byte order, the function will now
do these things itself.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB hub driver's event handler contains a check to catch SuperSpeed
devices that transitioned into the SS.Inactive state and tries to fix
them with a reset. It decides whether to do a plain hub port reset or
call the usb_reset_device() function based on whether there was a device
attached to the port.

However, there are device/hub combinations (found with a JetFlash
Transcend mass storage stick (8564:1000) on the root hub of an Intel
LynxPoint PCH) which can transition to the SS.Inactive state on
disconnect (and stay there long enough for the host to notice). In this
case, above-mentioned reset check will call usb_reset_device() on the
stale device data structure. The kernel will send pointless LPM control
messages to the no longer connected device address and can even cause
several 5 second khubd stalls on some (buggy?) host controllers, before
finally accepting the device's fate amongst a flurry of error messages.

This patch makes the choice of reset dependent on the port status that
has just been read from the hub in addition to the existence of an
in-kernel data structure for the device, and only proceeds with the more
extensive reset if both are valid.
Signed-off-by: NJulius Werner <jwerner@chromium.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB hub driver's event handler contains a check to catch SuperSpeed
devices that transitioned into the SS.Inactive state and tries to fix
them with a reset. It decides whether to do a plain hub port reset or
call the usb_reset_device() function based on whether there was a device
attached to the port.

However, there are device/hub combinations (found with a JetFlash
Transcend mass storage stick (8564:1000) on the root hub of an Intel
LynxPoint PCH) which can transition to the SS.Inactive state on
disconnect (and stay there long enough for the host to notice). In this
case, above-mentioned reset check will call usb_reset_device() on the
stale device data structure. The kernel will send pointless LPM control
messages to the no longer connected device address and can even cause
several 5 second khubd stalls on some (buggy?) host controllers, before
finally accepting the device's fate amongst a flurry of error messages.

This patch makes the choice of reset dependent on the port status that
has just been read from the hub in addition to the existence of an
in-kernel data structure for the device, and only proceeds with the more
extensive reset if both are valid.
Signed-off-by: NJulius Werner <jwerner@chromium.org>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This patch removes a redundant nested "#ifdef CONFIG_PM" from the hub
driver.  It also adds a label to the "#endif" line corresponding to
the outer "#ifdef CONFIG_PM".
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Control transfers have both IN and OUT (or SETUP) packets, so when
clearing TT buffers for a control transfer it's necessary to send
two HUB_CLEAR_TT_BUFFER requests to the hub.
Signed-off-by: NWilliam Gulland <wgulland@google.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The hub driver was recently changed to use "global" suspend for system
suspend transitions on non-SuperSpeed buses.  This means that we don't
suspend devices individually by setting the suspend feature on the
upstream hub port; instead devices all go into suspend automatically
when the root hub stops transmitting packets.  The idea was to save
time and to avoid certain kinds of wakeup races.

Now it turns out that many hubs are buggy; they don't relay wakeup
requests from a downstream port to their upstream port if the
downstream port's suspend feature is not set (depending on the speed
of the downstream port, whether or not the hub is enabled for remote
wakeup, and possibly other factors).

We can't have hubs dropping wakeup requests.  Therefore this patch
goes partway back to the old policy: It sets the suspend feature for a
port if the device attached to that port or any of its descendants is
enabled for wakeup.  People will still be able to benefit from the
time savings if they don't care about wakeup and leave it disabled on
all their devices.

In order to accomplish this, the patch adds a new field to the usb_hub
structure: wakeup_enabled_descendants is a count of how many devices
below a suspended hub are enabled for remote wakeup.  A corresponding
new subroutine determines the number of wakeup-enabled devices at or
below an arbitrary suspended USB device.

This should be applied to the 3.10 stable kernel.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NToralf Förster <toralf.foerster@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_hub_to_struct_hub() can return NULL in some unlikely cases.
Add checks where appropriate, or pass the hub pointer as an additional
argument if it's known to be valid.

The places it makes sense to check usb_hub_to_struct_hub()
are picked based on feedback from Alan Stern.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1675) removes the CONFIG_USB_SUSPEND option, essentially
replacing it everywhere with CONFIG_PM_RUNTIME (except for one place
in hub.c, where it is replaced with CONFIG_PM because the code needs
to be used in both runtime and system PM).  The net result is code
shrinkage and simplification.

There's very little point in keeping CONFIG_USB_SUSPEND because almost
everybody enables it.  The few that don't will find that the usbcore
module has gotten somewhat bigger and they will have to take active
measures if they want to prevent hubs from being runtime suspended.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1674) speeds up system sleep transitions by not
suspending each individual device on a USB-1.1 or USB-2 bus.  The
devices will automatically go into suspend when their root hubs are
suspended (i.e., stop sending out Start-Of-Frame packets) -- this is
what the USB spec calls "global suspend".

Since this is what we do already when CONFIG_USB_SUSPEND isn't
enabled, it shouldn't cause any problems.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1673) reduces the amount of log spew from the hub driver
by removing a bunch of error messages in the case where the device in
question is already known to have been disconnected.  Since the
disconnect event itself appears in the log, there's no need for other
error messages.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NJenya Y <jy.gerstmaier@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Return an error if hub->descriptor->bNbrPorts==0. Without this additional
check, we can end up doing a "hub->ports = kzalloc(0, GFP_KERNEL)".
This hub->ports pointer will therefore be non-NULL and will be used.
Example of dmesg:
   INIT: usb 1-1: New USB device found, idVendor=0424, idProduct=2512
   usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
   hub 1-1:1.0: USB hub found
   version 2.86 bootinghub 1-1:1.0: 0 ports detected
   Unable to handle kernel NULL pointer dereference at virtual address 00000010
Signed-off-by: NDavid Linares <dlinares.linux@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If one storage interface or usb network interface(iSCSI case) exists in
current configuration, memory allocation with GFP_KERNEL during
usb_device_reset() might trigger I/O transfer on the storage interface
itself and cause deadlock because the 'us->dev_mutex' is held in
.pre_reset() and the storage interface can't do I/O transfer when the
reset is triggered by other interface, or the error handling can't be
completed if the reset is triggered by the storage itself (error
handling path).
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Decotigny <david.decotigny@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Reviewed-by: NJiri Kosina <jkosina@suse.cz>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch is to add usb port auto power off mechanism.
When usb device is suspending, usb core will suspend usb port and
usb port runtime pm callback will clear PORT_POWER feature to
power off port if all conditions were met. These conditions are
remote wakeup disable, pm qos NO_POWER_OFF flag clear and persist
enable. When it resumes, power on port again.

Add did_runtime_put in the struct usb_port to ensure
pm_runtime_get/put(portdev) to be called pairedly.  Set did_runtime_put
to true when call pm_runtime_put(portdev) during suspending. The
pm_runtime_get(portdev) only will be called when did_runtime_put
is set to true during resuming. Set did_runtime_put to false after
calling pm_runtime_get(portdev).

Make clear_port_feature() and hdev_to_hub() as global symbol.
Rename clear_port_feature() to usb_clear_port_feature() and
hdev_to_hub() to usb_hub_to_struct_hub().

Extend hub_port_debounce() with the fuction of debouncing to
be connected. Add two wraps: hub_port_debounce_be_connected()
and hub_port_debouce_be_stable().

Increase HUB_DEBOUNCE_TIMEOUT to 2000 because some usb ssds
needs around 1.5 or more to make the hub port status to be
connected steadily after being powered off and powered on.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch is to add runtime pm callback for usb port device.
Set/clear PORT_POWER feature in the resume/suspend callback.
Add portnum for struct usb_port to record port number. Do
pm_rumtime_get_sync/put(portdev) when a device is plugged/unplugged
to prevent it from being powered off when it is active.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Usb3.0 device defines function remote wakeup which is only for interface
recipient rather than device recipient. This is different with usb2.0 device's
remote wakeup feature which is defined for device recipient. According usb3.0
spec 9.4.5, the function remote wakeup can be modified by the SetFeature()
requests using the FUNCTION_SUSPEND feature selector. This patch is to use
correct way to disable usb3.0 device's function remote wakeup after suspend
error and resuming.

This should be backported to kernels as old as 3.4, that contain the
commit 623bef9e "USB/xhci: Enable remote
wakeup for USB3 devices."
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

ACPI provide "_PLD" and "_UPC" aml methods to describe usb port
visibility and connectability. This patch is to add usb_hub_adjust_DeviceRemovable()
to adjust usb hub port's DeviceRemovable according ACPI information and invoke it in
the rh_call_control(). When hub descriptor request is issued at first time,
usb port device isn't created and usb port is not bound with acpi. So first
hub descriptor request is not changed based on ACPI information. After usb
port devices being created, call usb_hub_adjust_DeviceRemovable in the hub_configure()
and then set hub port's DeviceRemovable according ACPI information and this also works
for non-root hub.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

To show the relationship between usb port and child device,
add link file "port" under usb device's sysfs directoy and
"device" under usb port device's sysfs directory. They are linked
to each other.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch is to create driver/usb/core/(port.c,hub.h) files and move usb
port related code into port.c.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Sarah pointed out that the USB3.0 spec also updates the amount of power
that may be consumed by the device and quoted 9.2.5.1:

|"The amount of current draw for SuperSpeed devices are increased to 150
|mA for low-power devices and 900 mA for high-power"

This patch tries to update all users to use the larger values for
SuperSpeed devices and use the "old" ones for everything else.

While here, two other changes suggested by Alan:
- the comment referering to 7.2.1.1 has been updated to 7.2.1 which is
  the correct source of the action.
- the check for hubs with zero ports has been removed.
- compute bus power by full_load * num_ports on root hubs
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>