- 28 11月, 2011 1 次提交
-
-
now sam9_smc_configure will take as first parameter is the SMC id Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
- 11 9月, 2011 1 次提交
-
-
由 Dmitry Eremin-Solenikov 提交于
Currently atmel_nand driver used by AT91 and AVR32 calls a special callback which return nand partition table and number of partitions. However in all boards this callback returns just static data. So drop this callback and make atmel_nand use partition table provided statically via platform_data. Nicolas Ferre: I am in favor for a mainline inclusion through linux-mtd tree. Hans-Christian Egtvedt: I'm fine by sending the changes for AVR32 through linux-mtd Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com> Acked-by: NHans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
-
- 08 8月, 2011 1 次提交
-
-
由 Russell King 提交于
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h before we start consolidating the individual platform implementations of the gpio header files. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 28 7月, 2011 2 次提交
-
-
they are the same except the default priority Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
-
On all at91 except rm9200 and x40 have the System Controller starts at address 0xffffc000 and has a size of 16KiB. On rm9200 it's start at 0xfffe4000 of 111KiB with non reserved data starting at 0xfffff000 This patch removes the individual definitions of AT91_BASE_SYS and replaces them with a common version at base 0xfffffc000 and size 16KiB and map the same memory space Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
-
- 05 7月, 2011 1 次提交
-
-
由 Nicolas Ferre 提交于
The recently modified nand buswitth configuration is not aligned with board reality: the double footprint on boards is always populated with 8bits buswidth nand flashes. So we have to consider that without particular configuration the 8bits buswidth is selected by default. Moreover, the previous logic was always using !board_have_nand_8bit(), we change it to a simpler: board_have_nand_16bit(). Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Tested-by: NLudovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
- 25 5月, 2011 3 次提交
-
-
select ARM_PATCH_PHYS_VIRT as with ARM_PATCH_PHYS_VIRT you can patch boot_params at runtime or any recent bootloader will provide a valid atags pointer in r2 as point out by Russell on AT91 we never use XIP so se do not need PLAT_PHYS_OFFSET Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com> Cc: Andrew Victor <linux@maxim.org.za> Cc: Russell King <rmk+kernel@arm.linux.org.uk>
-
switch early init to init_early and introduce soc map_io with this Patch we will not do any more early device setup during the map io tks to Russell to point the new call back Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com> Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk> Acked-by: NAndrew Victor <linux@maxim.org.za>
-
no board configure it as 'n' and it's an issue to merge all defconfigs in one On AT91SAM926x boards both types of NAND flash can be present (8 and 16 bit data bus width). so will pass it via system_rev Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
-
- 20 10月, 2010 1 次提交
-
-
由 Nicolas Pitre 提交于
Since we're now using addruart to establish the debug mapping, we can remove the io_pg_offst and phys_io members of struct machine_desc. The various declarations were removed using the following script: grep -rl MACHINE_START arch/arm | xargs \ sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }' [ Initial patch was from Jeremy Kerr, example script from Russell King ] Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org> Acked-by: Eric Miao <eric.miao at canonical.com>
-
- 23 9月, 2009 1 次提交
-
-
由 Marc Kleine-Budde 提交于
This patch activates the at91 CAN controller for the at91sam9263ek development board. Signed-off-by: NHans J. Koch <hjk@linutronix.de> Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de> Acked-by: NWolfgang Grandegger <wg@grandegger.com> Acked-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 9月, 2009 1 次提交
-
-
由 Samuel R. C. Vale 提交于
DBGU means Debug Unit, was refered as "DGBU" in some files. Fixed to "DBGU". Signed-off-by: NSamuel R. C. Vale <srcvale@holoscopio.com> Acked-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 07 9月, 2009 2 次提交
-
-
由 Nicolas Ferre 提交于
Board code was wrongly setting up the reset pin for AC97 on at91sam9263ek. Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Acked-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 sedji gaouaou 提交于
This patch modifies the support of AC97 on the at91sam9263 ek board, so it would share the code with AVR32. Plus it removes a typo in at91sam9263_devices.c. Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 02 12月, 2008 1 次提交
-
-
由 Andrew Victor 提交于
Convert the SAM9 and CAP9 board-specific files to make use of the sam9_smc_configure() method to configure the memory-controller for external peripherals. The following boards have been modified: cam60 : NAND cap9adk : NAND, NOR qil-a9260 : NAND sam9-l9260 : NAND sam9260ek : NAND sam9261ek : DM9000 Ethernet, NAND sam9263 : NAND sam9g20ek : NAND sam9rlek : NAND usb-a9260 : NAND usb-a9263 .: NAND Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 22 9月, 2008 3 次提交
-
-
由 Andrew Victor 提交于
Allow the various GPIO-connected buttons to be used as wakeup sources. Also enable the internal GPIO pullup. Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
Use the PWM controller and leds-atmel-pwm.c driver to drive a LED on the Atmel AT91SAM9263-EK board. Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
In the various AT91 board files, replace hard-coded size values (eg, 0x800000) with the SZ_ size definitions (eg, SZ_8M) from sizes.h Also replace MTD partition offsets with MTDPART_OFS_NXTBLK. Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 19 9月, 2008 1 次提交
-
-
由 David Brownell 提交于
The at91sam9260 and at91sam9263 EK boards have 64 KiB I2C EEPROMs. This patch declares them in the board init code so the new at24 driver will use them. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Acked-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 07 8月, 2008 2 次提交
-
-
由 Russell King 提交于
This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h. Then, since asm/hardware.h only exists to include asm/arch/hardware.h, update everything to directly include asm/arch/hardware.h and remove asm/hardware.h. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 01 8月, 2008 1 次提交
-
-
由 Pieter du Preez 提交于
Structs called at91_nand_data where renamed to atmel_nand_data and configs called *MTD_NAND_AT91* where renamed to *MTD_NAND_ATMEL*. This was unfortunately not done consistently, causing NAND chips not being initialised on several ARM boards. I am aware that the author of the original change did not rename MTD_NAND_AT91_BUSWIDTH to MTD_NAND_ATMEL_BUSWIDTH, for example. All *MTD_NAND_AT91* where renamed to *MTD_NAND_ATMEL* in order to keep naming consistency. This patch was only tested on a MACH_SAM9_L9260, as this is the only ARM board I have to my disposal. Before this patch: $ git-ls-files |xargs grep atmel_nand |wc -l 105 $ git-ls-files |xargs grep at91_nand |wc -l 4 $ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l 8 $ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l 47 After this patch: $ git-ls-files |xargs grep atmel_nand |wc -l 109 $ git-ls-files |xargs grep at91_nand |wc -l 0 $ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l 55 $ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l 0 Signed-off-by: NPieter du Preez <pdupreez@gmail.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
- 07 6月, 2008 1 次提交
-
-
由 Håvard Skinnemoen 提交于
This is basically s/at91_nand/atmel_nand/g with some manual inspection. Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
-
- 04 4月, 2008 3 次提交
-
-
由 Andrew Victor 提交于
Add support for the GPIO-driven LEDs (using NEW_LEDS) on the Atmel SAM9260-EK and SAM9261-EK boards. Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
Convert the Atmel SAM9260-EK, SAM9261-EK, SAM9263-EK and SAM9RL-EK boards to use the new-style UART initialization. Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
The AT91CAP9 processor includes the same Static Memory Controller (SMC) peripheral as the SAM9 processors, but replaces the SDRAM Controller with a DDR/SDR Controller (DDRSDRC). This patch splits the existing include/asm-arm/arch-at91/at91sam926x_mc.h into at91sam9_sdramc.h and at91sam9_smc.h. It also adds an at91cap9_ddrsdr.h for the DDRSDRC controller. Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 06 3月, 2008 1 次提交
-
-
由 Nicolas Ferre 提交于
Correct GPIO pin assignment for the LCD power control (PCI) Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Cc: David Brownell <david-b@pacbell.net> Cc: Andrew Victor <linux@maxim.org.za> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 07 2月, 2008 1 次提交
-
-
由 David Brownell 提交于
On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from the LCD controller. It's controlled by "contrast" registers though. This patch lets boards declare that they have that kind of backlight control. The driver can then export this control, letting screenblank and other operations actually take effect ... reducing the typically substantial power drain from the backlight. Note that it's not fully cooked - doesn't force backlight off during system suspend - the "power" and "blank" events may not be done right This should be easily added in the future. [nicolas.ferre@atmel.com: remove unneeded inline and rename functions] Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <linux@maxim.org.za> Cc: Russell King <rmk@arm.linux.org.uk> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 28 1月, 2008 1 次提交
-
-
由 David Brownell 提交于
From: Nicolas Ferre <nicolas.ferre@rfo.atmel.com> On the at92sam9263ek board, tell the input subsystem about the buttons. This patch is taken from Andrew Victor's at91 patchset, then updated to match the latest kernel code and to use labels printed on the board. Also update the at91sam9261ek buttons to cope with input changes. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Acked-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 26 1月, 2008 2 次提交
-
-
由 Andrew Victor 提交于
Add NEW_LEDs support for the following boards: - Cogent CSB337 - Atmel AT91RM9200-DK - Atmel AT91RM9200-EK - Atmel AT91SAM9263-EK Mostly based on patch from David Brownell. Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 David Brownell 提交于
On the at92sam9263ek board, tell the MACB driver the IRQ used by its PHY. This patch is taken from Andrew Victor's 2.6.23-at91 patchset; it matches board schematics. (But it's currently a NOP since the MACB driver doesn't yet use PHY irqs.) Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 27 11月, 2007 1 次提交
-
-
由 Andrew Victor 提交于
The AT91 I2C driver is currently marked as "broken" due to hardware issues. This patch enables AT91-based platforms to also use the bitbanged GPIO for I2C. This updates platform setup logic (setting up an i2c-gpio device using the same pins as the i2c-at91 device, unless only the BROKEN driver is enabled). Also make use of the new-style initialization of I2C devices using i2c_register_board_info(). Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 12 7月, 2007 1 次提交
-
-
由 Andrew Victor 提交于
Add board-specific setup for the LCD on the Atmel AT91SAM9261-EK and AT91SAM9263-EK boards. Signed-off-by: NNicolas Ferre <nicolas.ferre@rfo.atmel.com> Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 31 5月, 2007 1 次提交
-
-
由 Russell King 提交于
The following patch fixes these section mismatch warnings: WARNING: arch/arm/mach-at91/built-in.o(.text+0xdf4): Section mismatch: reference to .init.data:dk_nand_partition (between 'nand_partitions' and 'at91_leds_event') WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (after 'nand_partitions') WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (between 'nand_partitions' and 'ads7843_pendown_state') WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (after 'nand_partitions') WARNING: arch/arm/mach-at91/built-in.o(.text+0xc28): Section mismatch: reference to .init.data:kb9202_nand_partition (after 'nand_partitions') WARNING: arch/arm/mach-footbridge/built-in.o(.text+0xaa4): Section mismatch: reference to .init.data:cats_pci (between 'cats_pci_init' and 'ebsa285_leds_event')WARNING: arch/arm/mach-ixp2000/built-in.o(.text+0xb54): Section mismatch: reference to .init.text:ixp2000_init_irq (between 'ixdp2x00_init_irq' and 'ixdp2x00_irq_handler') WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x670): Section mismatch: reference to .init.text:ixp23xx_pci_common_init (between 'ixp23xx_pci_slave_init' and 'ixp23xx_pci_scan_bus') WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x890): Section mismatch: reference to .init.text:ixp23xx_init_irq (between 'ixdp2351_init_irq' and 'roadrunner_pci_preinit') WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x9a8): Section mismatch: reference to .init.text:ixp23xx_pci_preinit (after 'roadrunner_pci_preinit') WARNING: arch/arm/mach-imx/built-in.o(__ksymtab+0x80): Section mismatch: reference to .init.text:imx_set_mmc_info (between '__ksymtab_imx_set_mmc_info' and '__ksymtab_set_imx_fb_info') WARNING: arch/arm/mach-imx/built-in.o(__ksymtab+0x88): Section mismatch: reference to .init.text:set_imx_fb_info (after '__ksymtab_set_imx_fb_info') WARNING: arch/arm/mach-sa1100/built-in.o(.text+0x1930): Section mismatch: reference to .init.data:neponset_port_fns (between 'neponset_probe' and 'assabet_leds_event') WARNING: drivers/built-in.o(.text+0x3f100): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted') WARNING: drivers/built-in.o(.text+0x3f1c8): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted') WARNING: drivers/built-in.o(.text+0x4f988): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted') WARNING: drivers/built-in.o(.text+0x4fa50): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted') Signed-off-by: NSam Ravnborg <sam@ravnborg.org> Acked-by: NLennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 04 5月, 2007 1 次提交
-
-
由 Andrew Victor 提交于
Various small changes for the Atmel AT91SAM9260-EK and AT91SAM9263-EK boards. SAM9260-EK: - Register I2C device. SAM9263-EK: - Add platform_data and register MACB device. (Patch by Nicolas Ferre) - Add platform_data and register AC97 device. (Patch by Nicolas Ferre) - Register I2C device. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 03 5月, 2007 1 次提交
-
-
由 Andrew Victor 提交于
Add support for the ADS7846 Touchscreen found on the Atmel AT91SAM9263-EK board. Signed-off-by: NNicolas Ferre <nicolas.ferre@rfo.atmel.com> Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 08 2月, 2007 4 次提交
-
-
由 Andrew Victor 提交于
Add support for the Atmel AT91SAM9263-EK board. Original patch from Nicolas Ferre. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
The Atmel AT91SAM9263 processor includes many more integrated peripherals than Atmel's previous ARM9-based AT91 processors, so this has necessitated a few changes to the core AT91 support. These changes are: * The system peripheral I/O region we remap has increased from 0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF. * The increased I/O region forces changes to entry-macro.S and debug-macro.S due to ARM's limited immediate offset addressing modes. * Maximum number of GPIO banks increases to 5. * 2 MMC controllers so the board-setup code needs to specify which controller it wishes to use when calling at91_add_device_mmc(). Original patch from Nicolas Ferre. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
Now that Linux includes support for the Atmel AT91SAM9260 and AT91SAM9261 processors in addition to the original Atmel AT91RM9200 (with support for more AT91 processors pending), the "mach-at91rm9200" and "arch-at91rm9200" directories should be renamed to indicate their more generic nature. The following git commands should be run BEFORE applying this patch: git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91 git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91 Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
Fix build failure of AT91SAM9260. The AT91RM9200 ethernet driver (at91_ether.c) stores platform data in a "struct at91_eth_data" structure, but the AT91SAM9260 (and AT91SAM9263) ethernet driver (macb.c) [developed on the AVR32 architecture] expects a "struct eth_platform_data". Since the platform data of the two drivers is very similar, we continue to use the "struct at91_eth_data" for all AT91 processors but add a #define eth_platform_data at91_eth_data in board.h to keep the MACB driver happy. Original patch by Jan Altenberg. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-