[ARM] 4354/1: AT91: Support ADS7846 touchsceen on SAM9263-EK board

Add support for the ADS7846 Touchscreen found on the Atmel
AT91SAM9263-EK board.
Signed-off-by: NNicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-at91/board-sam9263ek.c

@@ -25,6 +25,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
 
 #include <asm/hardware.h>
 #include <asm/setup.h>
@@ -85,6 +86,40 @@ static struct at91_udc_data __initdata ek_udc_data = {
 };
 
 
+/*
+ * ADS7846 Touchscreen
+ */
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+static int ads7843_pendown_state(void)
+{
+	return !at91_get_gpio_value(AT91_PIN_PA15);	/* Touchscreen PENIRQ */
+}
+
+static struct ads7846_platform_data ads_info = {
+	.model			= 7843,
+	.x_min			= 150,
+	.x_max			= 3830,
+	.y_min			= 190,
+	.y_max			= 3830,
+	.vref_delay_usecs	= 100,
+	.x_plate_ohms		= 450,
+	.y_plate_ohms		= 250,
+	.pressure_max		= 15000,
+	.debounce_max		= 1,
+	.debounce_rep		= 0,
+	.debounce_tol		= (~0),
+	.get_pendown_state	= ads7843_pendown_state,
+};
+
+static void __init ek_add_device_ts(void)
+{
+	at91_set_B_periph(AT91_PIN_PA15, 1);	/* External IRQ1, with pullup */
+	at91_set_gpio_input(AT91_PIN_PA31, 1);	/* Touchscreen BUSY signal */
+}
+#else
+static void __init ek_add_device_ts(void) {}
+#endif
+
 /*
  * SPI devices.
  */
@@ -97,6 +132,16 @@ static struct spi_board_info ek_spi_devices[] = {
 		.bus_num	= 0,
 	},
 #endif
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+	{
+		.modalias	= "ads7846",
+		.chip_select	= 3,
+		.max_speed_hz	= 125000 * 26,	/* (max sample rate @ 3V) * (cmd + data + overhead) */
+		.bus_num	= 0,
+		.platform_data	= &ads_info,
+		.irq		= AT91SAM9263_ID_IRQ1,
+	},
+#endif
 };
 
 
@@ -157,7 +202,10 @@ static void __init ek_board_init(void)
 	/* USB Device */
 	at91_add_device_udc(&ek_udc_data);
 	/* SPI */
+	at91_set_gpio_output(AT91_PIN_PE20, 1);		/* select spi0 clock */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+	/* Touchscreen */
+	ek_add_device_ts();
 	/* MMC */
 	at91_add_device_mmc(1, &ek_mmc_data);
 	/* NAND */