Convert mx23/mx28 dts files to use the padconfig defintions from
mxs-pinfunc.h.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Convert mx23/mx28 dts filed to use the pinctrl header files.

NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts

According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX

I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The early prototypes had the chip select pin for the LCD controller
wired on the GPIO 3-23, while the production run of the CFA-10049 have
this chip select on the GPIO 3-5.
Signed-off-by: NBrian Lilly <brian@crystalfontz.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The SSD1307 was used in an early prototype that will never get
distributed. The final board now has a SSD1306 instead, that has its own
power generation unit and thus doesn't need any PWM. The panel attached
to it also changed.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Move display timing configurations into device tree, so that the
auxdata for mxsfb driver can be killed.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The DAC found on the last chip select requires a word length of 12 bits,
which is not supported by the SSP controller of the iMX28. Use
bitbanging for that bus to support such a length.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add the GPIO expander found on the i2c1 bus, behind the muxer to the
device tree.

This gpio expander will be used to get tachymeters values and data ready
interruptions from the nuvoton NAU7802 ADCs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Use a hog_pins pinctrl group to force the muxing of GPIOs used on the
Crystalfonz CFA10036 and CFA10049 boards.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

There is no driver for it yet, so it will use spidev.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add the two daisy-chains of 74hc595s shift registers available on the
CFA-10049.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>