This patch:
 - enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
 - adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
   present on following boards:

   am43x-epos-evm:
	On this board, NAND Flash control lines are muxed with QSPI, Thus only
        one of the two can be used at a time. Selection is controlled by:
        (a) dynamically driving following GPIO pin from software
            GPMC_A0(GPIO) == 0 NAND is selected (default)
            GPMC_A0(GPIO) == 1 eMMC is selected
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updated MTD/NAND DT node binding to replace deprecated bindings
as per following commit.
    commit ac65caf5
    ARM: OMAP2+: cleaned-up DT support of various ECC schemes
    Also Refer: Documentation/devicetree/bindings/mtd/gpmc-nand.txt
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch has following updates, specific to MTD/NAND DT
 - update MTD NAND partition table to keep compatibility between
   different boards and mainline u-boot.
 - prefix 'NAND.' in names of NAND device MTD partitions to differentiate them
   from other MTD device partitions (like NOR and QSPI)
               Partition_Name            Partition_Size
    /dev/mtd0  NAND.SPL                  1 block-size*
    /dev/mtd1  NAND.SPL.backup1          1 block-size*
    /dev/mtd2  NAND.SPL.backup2          1 block-size*
    /dev/mtd3  NAND.SPL.backup3          1 block-size*
    /dev/mtd5  NAND.u-boot-spl-os        2 block-size* [for falcon boot]
    /dev/mtd4  NAND.u-boot               1 MB
    /dev/mtd6  NAND.u-boot-env           1 block-size*
    /dev/mtd7  NAND.u-boot-env.backup1   1 block-size*
    /dev/mtd8  NAND.kernel               till 0xA00000
    /dev/mtd9  NAND.file-system          till end of device

* am335x-evm uses NAND device with block-size=128KiB
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch
 - refactors gpmc_hwecc_bch_capable()
 - add checks for new platforms like dra7xx, am43xx
 - add checks for OMAP3 SoC, w.r.t. new ECC schemes spawned in following commit:
    commit ac65caf5
    ARM: OMAP2+: cleaned-up DT support of various ECC schemes
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add node for bma180 driver.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This requires vaux4.

Reset line isn't used yet, so wifi isn't reliable.
But it does work once per boot.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds basic sound support for gta04 board.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define twl4030 charger node used for charging.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Gta04 using tcs2007 touchscreen. Add support for that.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add magnetometer hmc5843 node.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable second USB channel and set it into 'host' mode.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Making it possible to reference and therefor change (disable) this
device node from other dts file which import this dtsi file.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing interrupt properties to the ecap0, ecap1, and ecap2
nodes.
Signed-off-by: NMatt Porter <mporter@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP34xx, AM3517 and OMAP36xx platforms use dpll1 clock.

OMAP443x, OMAP446x, OMAP447x, OMAP5, DRA7, AM43xx platforms use
dpll_mpu clock.

Latency used is the generic latency defined in omap-cpufreq
driver.
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NAcked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

INCOstartec LILLY-DBB056 is a carrier board (baseboard) for
computer-on-module LILLY-A83X.

This patch adds device-tree support for most of its features.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

INCOstartec LILLY-A83X module is a TI DM3730xx100 (OMAP3) SoC
computer-on-module.

This patch adds device tree support for most of its features.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org> # 3.13.x
Signed-off-by: NTony Lindgren <tony@atomide.com>

In omap2420.dtsi and omap2430.dtsi disable all mcbsp nodes and board dts
files can explicitly enable the mcbsp they are using.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In omap3.dtsi disable all mcbsp nodes and board dts files can explicitly
enable the mcbsp they are using.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Board dts files will need to enable the IP nodes which they are using and
does not have to care about the not used ones (to disable them).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Board dts files will need to enable the IP nodes which they are using and
does not have to care about the not used ones (to disable them).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Attach the pinctrl nodes to their respective device node:
mcbsp1, mcbsp2, dmic, mcpdm and twl6040.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Attach the pinctrl nodes to their respective device node:
mcbsp1, mcpdm and twl6040.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the hwspinlock device tree node for AM43xx family
of SoCs.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the hwspinlock device tree node for DRA7 SoCs.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add a new generic property "#hwlock-cells" to the hwspinlock
DT nodes on OMAP4, OMAP5 and AM33xx. This common property allows
different platform implementations to define the args specifier
length. OMAP implementations will always use a value of 1.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

sbc-t3x boards features two external USB ports on SB-T35 baseboard.
The baseboardi USB hub reset signal should be de-asserted to make
those ports functional.

sbc-t3517 features additional (assembled on CoM) USB hub which also
requires reset signal handling.

Add quirks code to handle proper reset pulse signal.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for CM-T3517 CoM and SBC-T3517 board.

reused common support for sbc-t3x boards
(omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi):

* SB-T35 baseboard eth
* MMC1, UART3
* HS USB Port 1/2
* I2C1/3
* Heartbit led

Added basic support for:

* MMC1 wp/cd signals
* CM-T3517 Usb Hub
* WL12xx WiFi chip
* Davinci EMAC
* AM35X OTG
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for CM-T3530 CoM and SBC-T3530 board.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add USB OTG support for cm-t3x30 CoMs.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPIO167 is used as SB-T35 baseboard USB Hub reset.
Add GPIO167 pinmux.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add HS USB Host support along with USB PHYs and power supply regulators
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add pullup for twl4030 GPIO_0 used as MMC1 card detect signal.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPIO186 is used for the heartbeat led.
Setup the pinmux for the GPIO186.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

SB-T35 baseboard features SMSC9220 Ethernet chip which requires
its own power supply regulators.

Add baseboard specific regulators for the SB-T35 Ethernet chip.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Disable mmc3 interface, since is not used on sbc-t3x boards.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Refactor the sbc-t3x device tree as a preparation for additional
(sbc-t3530, sbc-t3517, etc.) boards support.

No functional changes.

The device tree will have the following structure:

omap3-cm-t3x.dtsi
 |
 |<-- omap3-cm-t3x30.dtsi
 |     |
 |     |
 |     |     -----                  -------          ------------
 |     |    | CoM |                | Board |        | Base board |
 |     |     -----                  -------          ------------
 |     |                                            omap3-sb-t35.dtsi
 |     |                                                  |
 |     |<-- omap3-cm-t3730.dts <-- omap3-sbc-t3730.dts -->|
 |     |                                                  |
 |     |<-- omap3-cm-t3530.dts <-- omap3-sbc-t3530.dts -->|
 |                                                        |
 |<-------- omap3-cm-t3517.dts <-- omap3-sbc-t3517.dts -->|
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure
the padconf register offset.

This simplify further support of CompuLab's boards based on omap36xx,
omap34xx and am35x.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>