There is a race between updating the irq mask and setting it
which can be triggered on SMP with a bad cable.
Similar patch from Ingo Molnar and Thomas Gleixner
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Don't need to keep Yukon-2 related definitions around for Skge
driver that is only for Yukon-1 and Genesis.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

When skge is booted up, the PHY may be stuck in power down state
by the previous OS. So we may need to turn it on.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Cleanup receive buffer allocation and management,
Add more error handling checks from PHY and bump version.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Merge of four previous patches and the Kconfig fix
 * Remove debug printk's
 * whitespace cleanup and version number change
 * clear interrupts, reset phy, and reset hardware on shutdown
 * ignore 64bit counter overflow interrupts
 * fix a couple of places where second port could clobber state
   of first port.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Cleanup the code that handles fibre vs copper detection.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

 drivers/net/skge.c |   26 ++++++++++++--------------
 drivers/net/skge.h |   11 ++---------
 2 files changed, 14 insertions(+), 23 deletions(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Some versions of the Marvell yukon generate bogus sensor warning interrupts.
The driver would flood log with these messages.  Handle this situation
cleanly by masking away at boot time.

Fixes: http://bugs.gentoo.org/show_bug.cgi?id=87182Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

 drivers/net/skge.c |   24 ++++++++++--------------
 drivers/net/skge.h |    8 ++++++--
 2 files changed, 16 insertions(+), 16 deletions(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Cleanup code that is used to toggle LED's. Since we
get called from ethtool, can use that thread rather than
setting up a timer.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

During autonegotiation set PHY interrupt mask to ignore
bogus speed change interrupts.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The code to clear fifo errors was incorrect and sending garbage
to the external phy. Removed the no longer used inline's funcs.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Minor whitespace cleanups.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Missing PCI_REV_DESC define.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Optimize the receive buffer management code to replenish the
buffers immediately (like tg3).
Signed-off-by: NStephen Hemmminger <shemminger@osdl.org>

Need to handle receive and transmit packet arbiter timeouts.
Transmit arbiter timeouts happens when Gigabit sends to 100Mbit port
on same switch and pause occurs.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Cleanup messages (for debug) about PHY interrrupts, because when
user can't get driver working that is often the problem.
Use a consistent way of enabling interrupts by port.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Rewrite the code for handling the Broadcom PHY to something that
works. Remove link polling because Broadcom and Yukon don't need it.
When I wrote initial code, didn't have a genesis chipset based
board to test, so it was a non-working guess.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Get rid of definitions for chip versions and PHY chips that
this driver does not support.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Replace inline accessor functions for chip revision and number of ports
with simple structure members.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

The inlines and macro's needed some cleanup's and fixes:
 * change name of macro SKGEMAC_REG to SK_REG to better reflect usage
   and fix comments
 * ditto for SK_GEXM_REG -> SK_XMAC_REG and SKGEGMA_REG -> SK_GMA_REG

 * change skge_gm_ to just gm_ since it is just a local function and long
   names look ugly.
 * change skge_xm_ to just xm_
 * fix xm_write32 to write as two u16's with correct byte order
 * fix xm_outaddr to correctly use offset
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Cleanup whitespace around if() and switch() and end of lines
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>