drivers/net/tlan.c compiles with CONFIG_PCI=n only with a warning and
due to the dead code elimination of gcc.

Additionally, this fixes the only compile error I found with
CONFIG_PCI=n and the gcc -Werror-implicit-function-declaration
flag on i386.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

tty_schedule_flip() would schedule a thread that would call flush_to_ldisc().
If tty_buffer_request_room() gets called prior to that thread running --
which is likely in this loop in hvc_poll(), it would set the active flag
in the tty buffer and consequently flush_to_ldisc() would ignore it.

The result is that input on the hvc console is not processed.

This fix calls tty_flip_buffer_push (and flags the tty as
"low_latency").  The push to the ldisc thus happens synchronously.
Signed-off-by: NMichal Ostrowski <mostrows@watson.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The most usable number of ifb devices is 2. Change the default to 2.
Signed-off-by: NRichard Lucassen <spamtrap@lucassen.org>
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a race between updating the irq mask and setting it
which can be triggered on SMP with a bad cable.
Similar patch from Ingo Molnar and Thomas Gleixner
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

The SysKonnect Genesis based board would fail on initialization
with phy_read errors caused by not waiting for last phy write.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Fix a race in the receive NAPI, irq handling. The interrupt clear and the
start need to be separated.  Otherwise there is a window between the last
frame received and the NAPI done level handling.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Similar to 8139cp code but more inspired/lucky.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

rtl8169_hw_start() requires that the descriptor ring indexes be
set to zero. Let a deferred invocation of rtl8169_reset_task()
handle it. Enabling a few power management bits will not hurt
either.

suspend/resume is issued with irq on: the spinlock do not need
to save the irq flag.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Since about Linux 2.6.14, sbp2's inquiry workaround did not work anymore
due to changes in the SCSI layer. Update it to become effective again.
Testing one of the two known affected bridges has shown that skip_ms_page_8
is required as well.

Also, make force_inquiry_hack tunable via /sys/module/sbp2/parameters.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NJody McIntyre <scjody@modernduck.com>
(cherry picked from 99496037c6744fd938ffb8ccfc8fc91762322ff8 commit)

Let the ieee1394 core select a suitable 1394 address range for sbp2's
status FIFO instead of using a fixed range. Since the core only selects
addresses which are guaranteed to be out of the "physical range" as per
OHCI 1.1, this patch also fixes an old bug:

OHCI controllers which implement a writeable PhysicalUpperBound register
included sbp2's status FIFO in the physical range. That way sbp2 was
never notified of a succesful login and always failed after timeout.
Affected OHCI host adapters include ALi and Fujitsu controllers.

As another side effect of this patch, the status FIFO is no longer
located in a range for which OHCI chips perform "posted writes". Each
status write now requires a response subaction. But since large data
transfers involve only few status writes, there is no measurable
decrease of I/O throughput. What's more, the status FIFO is now safe
from potential host bus errors. Nevertheless, posted writes could be
re-enabled by extensions to the ARM features of the 1394 stack.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NJody McIntyre <scjody@modernduck.com>
(cherry picked from b2d38cccad4ef80d6b672b8f89aae5fe2907b113 commit)

If there were commands enqueued but not completed before an SBP-2 unit
was unplugged (or an attempt to reconnect failed), knodemgrd or any
process which tried to remove the device would sleep uninterruptibly
in blk_execute_rq().  Therefore make sure that all commands are
completed when sbp2 retreats.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NJody McIntyre <scjody@modernduck.com>
(cherry picked from 61daa34c132c5d4ed8630e2c46e9bf2f0c7b3428 commit)

Need to avoid race in updating IRQ mask.  This can probably be replaced
smarter use of the interrupt control registers (if/when chipset
docs are available).
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

To avoid problems with PCI config access without ACPI (or busted ACPI tables),
use the device's window into PCI config space.

I know this probably will upset the purists, but I would rather have users
than ACPI testers. It also generates less code.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Need to force a transmit coalesce timer restart after processing
transmit packets. Otherwise, can get transmit status after last
update and chip doesn't send the next one.

Can go with the chip defaults for coalescing timers, except for
Tx timer which needs to be bigger.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Need to restart the interrupt coalescing timer after clearing the interrupt,
to avoid races with interrupt timer and processing.

Patch from Carl-Daniel Halfinger
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Don't allow coalescing values to be bigger than the transmit ring.
Since if you set them that big, the interrupt never happens and driver
livelocks.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Add more complete setup code for Yukon EC_U chipset.
Based on matching code in 8.31 code in SysKonnect vendor driver.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

esp_reset didn't get fixed when the EH locking changed.
->eh_bus_reset_handler is now called without the host lock held.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A typo crept into the le32_to_cpu patch which broke 256-bit keys
in the padlock driver.  The following patch based on observations
by Michael Heyse fixes the problem.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Revert dasd eer module until we have a common understanding of how the
interface should be.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When using the dasd diag discipline, the base discipline module (eckd or fba)
can be unloaded, even though the dasd driver requires both discipline modules
(base and diag) to work correctly.

Implement reference counting for both base and diag discipline modules in
order to fix this.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Using FCP devices with V=V support, the input queue stalled when CCQ 97 had
been returned in qdio_do_eqbs.  When this happen we have to reissue the eqbs
instruction.

Another bug was when V=V was enabled we checked if hardware has SIGA-sync
support.  If not we returned with 0 from tiqdio_is_inbound_q_done.  Thus qdio
lost initiative on FCP devices and input queue stalled.  Running devices in
V=V there is no SIGA-sync support but nevertheless we have to process
tiqdio_is_inbound_q_done either.
Signed-off-by: NFrank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make resume from suspend-to-ram possible for Samsung P35 laptops.

The radeon mobility 9700 chip on Samsung P35 laptops locks up everything on
resume from suspend-to-ram if it is not reinitialized.

VGA compatible controller: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10]
Class 0300: 1002:4e50
       Subsystem: 144d:c00c

Unfortunately, the DMI strings are mostly identical for all Samsung
laptops.  So we match the PCI ID and subsystem ID of the graphics card
which is unique for each Samsung laptop model.
Signed-off-by: NCarl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The following message will be only printed if DEBUG_NOTIF is on.  "Unknown
notification: subtype=40,flags=0xa0,size=40"
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Cc: James Ketrenos <jketreno@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When attempting to open the device for writing, only return -EROFS if the disc
appears to be readable but not writable.
Signed-off-by: NPeter Osterlund <petero2@telia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix the pkt_writable_track() function to make it work correctly for all types
of CD/DVD discs.
Signed-off-by: NPeter Osterlund <petero2@telia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Writing the detected disc type in the kernel log is not useful during normal
use of the driver, so remove the printk statements.
Signed-off-by: NPeter Osterlund <petero2@telia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Boolean functions should return non-zero when they mean "true", otherwise the
calling code looks weird.  (As suggested by Linus.)
Signed-off-by: NPeter Osterlund <petero2@telia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It looks like the code in pkt_generic_packet() worked by luck in the past, but
after commit 186d330e leaving rq->cmd_len
uninitialized doesn't work any more.
Signed-off-by: NPeter Osterlund <petero2@telia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix two problems in the spi subsystem:

1) spi subsystem core dumps when modular spi master is unloaded.
2) spi subsystem core dumps when spi slave device is suspended/resumed and
   module slave driver is not loaded.
Signed-off-by: NStephen Street <stephen@streetfiresound.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I found an issue in cfi_cmdset0001.c.  It is related to cache region
invalidation in the buffered write procedure.

The code performs cache invalidation from "cmd_addr" to "cmd_adr + len" in
do_write_buffer() while we modify region from "adr" to "adr+len".

This issue affects writes + reads of data by small chunks.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some allocations are restricted to a limited set of nodes (due to memory
policies or cpuset constraints).  If the page allocator is not able to find
enough memory then that does not mean that overall system memory is low.

In particular going postal and more or less randomly shooting at processes
is not likely going to help the situation but may just lead to suicide (the
whole system coming down).

It is better to signal to the process that no memory exists given the
constraints that the process (or the configuration of the process) has
placed on the allocation behavior.  The process may be killed but then the
sysadmin or developer can investigate the situation.  The solution is
similar to what we do when running out of hugepages.

This patch adds a check before we kill processes.  At that point
performance considerations do not matter much so we just scan the zonelist
and reconstruct a list of nodes.  If the list of nodes does not contain all
online nodes then this is a constrained allocation and we should kill the
current process.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NDave Jones <davej@redhat.com>

This patch makes ata_sg_setup_one() trim sg entry (thus making
qc->n_elem zero) if padding results in zero length sg entry.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

For ATAPI commands, padding can reduce qc->n_elem by one and thus to
zero making assert(qc->n_elem > 0)'s in ata_fill_sg() and qs_fill_sg()
fail for legal commands.  This patch fixes the assert()'s to take
qc->pad_len into account.

Although the condition check seems a bit excessive, as this part of
code isn't still stable yet, I think it's worth to keep those.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch fixes 2 bugs in the USB-IrDA code.

The first one is a buffer overrun in the RX path. We are now using
IRDA_SKB_MAX_MTU when initializing the Rx URB.

The second one is a potential stack recursion when unplugging the USB
dongle.  It seems that first we get the Rx URB with a generic error
code, and after a while the Rx URB comes again with a "disconnect"
error code.  Since we are resubmitting the Rx URB immediately after
receiving the first error one, we might enter an endless loop.

When getting an error Rx URB, the patch defers the Rx URB resubmitting
so that it gives us a chance to catch the disconnect one, in case the
dongle has juts been unplugged.

Tested against 2.6.16-rc2.

Patch from Jean Tourrilhes
Signed-off-by: NJean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sbp2.c mangles INQUIRY response in a way that only applies to standard
inquiry data (i.e. when both cmddt and evpd bits are 0).  Leave other cases
alone; e.g. when asking for VPD the length of reply is in byte 3, not 4
and byte 4 is the first byte of device serial number.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NDave Airlie <airlied@linux.ie>

The Xgl on r300 doesn't work unless you add a verify bitblt function to the
DRM, and we need to pass TX_CNTL to flush texture caches.
Signed-off-by: NDave Airlie <airlied@linux.ie>