All interconnectable Marvell switch chips have an ATU Learn2All feature
which allows newly learnt addresses to be spanned on ports marked as
"Message Port".

This commit configures the DSA ports as Message Port. Note that this has
no effect until the Learn2All feature is enabled.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the configuration of the default ageing time in a new
mv88e6xxx_atu_setup function.

That function will be extended later to contain all ATU related
configuration bits.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the ATU ageing time setter code in a new global1_atu.c file, which
will be extended in future patches to contains all consequent Global (1)
ATU support code.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a mv88e6xxx_port_mask() helper to get the bitmask of ports in a
switch chip, that will be used in several features.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Add support for TC flower offload statistics

Arkadi says:
This patchset adds support for retrieving TC flower statistics for
offloaded rules, which includes packets count, bytes count and last used
time stamp. Currently The statistics are gathered on a per-rule basis.

This patchset also includes generic allocator for counters.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for TC flower offload statistics including number of packets,
bytes and last use timestamp. Currently the statistics are gathered on a
per-rule basis.
Signed-off-by: NArkadi Sharshvesky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for packets and byte statistics on TCAM entries. The counters
are allocated from the generic flow counters pool.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for Policing and Counting action block. This action block
will be used to bind counter to TCAM entries.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce periodic task for dumping the activity status for the ACL
rule TCAM entries. This is done in order to emulate last use statistics.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.comi>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the ACL rules can be accessed only by hashing. In order to
dump the activity the rules are also placed in a list.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for retrieving TCAM entry activity. In order to support ACL
rule activity corresponding TCAM entry should be queried.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for allocating generic flow counter. Generic flow counter
can count packets or packets and bytes and can be assigned to different
hardware processes. First use will be for counting packets and bytes of
ACL rules, and will be introduced in the following patches.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MGPC register retrieves generic flow counter value. It will be
used to query ACL counters.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add implementation for counter allocator. The ASIC has special memory
pool for various counting purposes. Counter memory is distributed between
equal size banks.

The static sub-pool configuration should specify the following parameters
for each sub-pool:
- Number of required banks.
- Maximum entry size.

Each module can add dedicated sub-pool or use existing one.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: XDP adjust head support

This series adds support for XDP adjust head.  Bulk of the code
is actually just paying technical debt.  On reconfiguration request
nfp was allocating new resources separately leaving device running
with the existing set of rings.  We used to manage the new resources
in special ring set structures.  This set is simply separating the
datapath part of the device structure from the control information
allowing the new datapath structure to be allocated with all new
memory and rings.  The swap operation is now greatly simplified.
We also save a lot of parameter passing this way.  Hopefully the churn
is worth the negative diffstat.

Support for XDP adjust head is done in a pretty standard way.  NFP
is a bit special because it prepends metadata before packet data
so we have to do a bit of memcpying in case XDP will run.  We also
luck out a little bit because the fact that we already have prepend
space allocated means that one byte is enough to store the extra XDP
space (256 of standard prepend space is a bit inconvenient since
it would normally require 16bits or boolean with additional shifts).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support prepending data from XDP.  We are already always allocating
some headroom because FW may prepend metadata to packets.
xdp_adjust_head() can be supported by making sure that headroom is
big enough for XDP.  In case FW had prepended metadata to the packet,
however, we have to move it out of the way before we call XDP.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

XDP may require us to move metadata to make room for pushing
headers.  Track meta data location with a pointer and pass
it explicitly to functions.

While at it validate that meta_len from the descriptor is not
bogus.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename pkt_off variable to dma_off, it should hold data offset
counting from beginning of DMA mapping.  Compute the value only
in XDP context.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP_NET_CFG_RX_OFFSET is 32bit wide, make sure what we read from
there is reasonable for packet headroom.  This allows us to store
the rx_offset in a 8bit variable.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of testing if xdp_prog is present store the dma direction
in data path structure.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of passing around sets of rings and their parameters just
store all information in the data path structure.

We will no longer user xchg() on XDP programs when we swap programs
while the traffic is guaranteed not to be flowing.  This allows us
to simply assign the entire data path structures instead of copying
field by field.

The optimization to reallocate only the rings on the side (RX/TX)
which has been changed is also removed since it seems like it's not
worth the code complexity.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use xdp_prog member of data path struct to carry the xdp_prog to
alloc/free free functions.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the mtu member from ring set to data path struct.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use fl_bufsz member of data path struct to carry desired size of
free list entries.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of passing variables around use dp to store number of tx rings
for the stack and number of IRQ vectors.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make callers of nfp_net_ring_reconfig() pass newly allocated data
path structure.  We will gradually make use of that structure
instead of passing parameters around to all the allocation functions.
This commit adds allocation and propagation of new data path struct,
no parameters are converted, yet.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Control BAR pointer is used to unmask interrupts so it should be
in the first cacheline of adapter structure.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all data path information into a separate structure.  This way
we will be able to allocate new data path with all new rings etc.
and swap it in easily.

No functional changes.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Joao Pinto says:

====================
prepare mac operations for multiple queues

As agreed with David Miller, this patch-set is the first of 3 to enable
multiple queues in stmmac.

This first one concentrates on mac operations adding functionalities as:
a) Configuration through DT
b) RX and TX scheduling algorithms programming
b) TX queues weight programming (essential in weightes algorithms)
c) RX enable as DCB or AVB (preparing for future AVB support)
d) Mapping RX queue to DMA channel
e) IRQ treatment prepared for multiple queues
f) Debug dump prepared for multiple queues
g) CBS configuration

In v3 patch-set version I included a new patch to enable CBS configuration
(Patch 9).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the configuration of the AVB Credit-Based Shaper.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares mac debug dump for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares mac irq status treatment for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adapts flow_ctrl function to prepare it for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the functionality of RX queue to dma channel mapping
based on configuration.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the enabling of RX queues as DCB or as AVB based
on configuration.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds TX queues weight programming.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the RX and TX scheduling algorithms programming.
It introduces the multiple queues configuration function
(stmmac_mtl_configuration) in stmmac_main.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the multiple queues configuration in the Device Tree.
It was also created a set of structures to keep the RX and TX queues
configurations to be used in the driver.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>