The priority flow control settings from the netlink layer aren't taking
effect in the base driver.  The boolean pfc_mode_enable in the dcb_config
struct isn't being set, so the hardware configuration code is never
reached.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethtool tries to get advertised speed from phy.autoneg_advertised.
However for copper media this wasn't happening until later do to
an other fix which moved mac.ops.setup_link_speed placement in
ixgbe_link_config(). This patch will display the default advertised
speeds if it can't yet get this information from phy.autoneg_advertised.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Acked-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ixgbe driver had issues when DEBUG was defined because the hw_dbg macro
was incomplete.  This patch completes the code based off of the code that
already existed in the igb module.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Impact: Fix

Yinghai Lu found one system with 82575EB where, in the kernel that is
kexeced, probe igb failed with -2, the reason being that the adapter
could not be brought back from D3 by the kexec kernel, most probably
due to quirky hardware (it looks like the same behavior happened on
forcedeth).

Prevent igb from putting the adapter into D3 during shutdown except
when we going to power off the system.  For this purpose, seperate
igb_shutdown() from igb_suspend() and use the appropriate PCI PM
callbacks in both of them.
Signed-off-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
Reported-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code path for setting up phy loopback testing was out of date and was
setting bits it didn't need to.  This change cleans up the code path and
removes some code that has no effect on teh driver.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increase the delay for copper phy init from 15ms to 100ms.  This is to
address issues seen in which ethtool -t was failing in some cases on 82576
based adapters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An issue was seen on suspend in which the system reported a page fault.  This
was due to the new reg_idx code being called after the queues were freed.

This update prevents any for loops from going through the queues by setting
the number of queues to 0 when they are freed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When device is on PCIe link trained as x2 the driver is currently reporting
link width as "unknown".  The original patch provided by Myron adds the x2
link support and my changes are cosmetic to clean up the readability of the
conditional operators.

Based on work by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FEC Ethernet device isn't always attached to a phy.  Be careful
not to dereference phy_device if it is NULL.  Also eliminates an
unnecessary extra function from the ioctl path.
Reported-by: NHenk Stegeman <henk.stegeman@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since not using net_device_ops gets you shunned out the cool crowd,
this patch modifies the fec_mpc52xx Ethernet driver to provide the
management hooks via a struct net_device_ops.
Reported-by: NHenk Stegeman <henk.stegeman@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver triggers a BUG_ON() when allocating DMA buffers because the
arch/powerpc dma_ops aren't in the net_device's struct device.  This
patch fixes the problem by using the parent of_device which does have
the correct dma_ops set.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Reviewed-by: NBecky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Kconfig and Makefile related changes for vxge driver.

- No changes in current submission.

- Changes from previous submission -
 - Incorporated the following review comments as per Bill Flink:
        - Add dependancy on INET along with PCI
        - Remove dependancy on INET_LRO and add GRO support.
 - Made this patch as last patch as per Ben Hutchings comments.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Driver version

- Changes from previous submission -
 - Updated driver version.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements all ethtool related entry point functions for the driver.

- Changes in this submission -
        - Removed redundant #include statements

- Changes in previous submissions -
        - Removed unused statistics.
        - General clean up - removed unused variables and macros.
 - Incorporated following comments from Ben Hutchings
        - No need to restart the interface in vxge_ethtool_sset
        - Do not use #ifdef ADVERTISED_XX
        - Remove unnecessart intermediate copy in vxge_ethtool_gdrvinfo
        - Use strlcpy() to ensure null-termination.
        - Use ethtool_op_get_tso, ethtool_op_set_tx_hw_csum instead
          of redefining the same code.
        - Implement get_strings_count instead of deprecated get_stats_count.
        - Don't report reporting the EEPROM length as we don't supprt
          get/set eeprom.
        - Don't set self_test_count as we don't support any self tests.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements all the driver entry point functions.
- Definition of all module loadable paramters.
- Implementation of all driver entry point functions.

- Changes in this submission -
        - Fixed compilation error when enabling debug statements
        - Fixed few warnings when CONFIG_PCI_MSI is not defined
        - Removed unnecessary volatile variables
        - Removed compare_ether_addr as it causes unaligned memory access on
          the sparc64 platform.

- Changes in previous submissions -
        - As per Stephen Hemminger's comments removed the following loadable
          parameters - gro, rx_& tx max_indicate_pkts, exec_mode, rx & tx
          pause_enable, tx_steering_type and intr_type.
        - Added Device ID definition in vxge-main.h instead of
          include/linux/pci_ids.h file - Reported by David Miller
 - Incorporated following review comments from Ben Hutchings
        - NAPI is always enabled (no option to turn it OFF).
        - Loadable parameters
         rx_steering_type: This loadable option is removed.
         ring_blocks: This loadable option is removed.
         The driver default settings work well in most if not all cases.
         Another patch to configure these parameters with ethtool will be
         released in the future.
 - LRO has been deprecated in favour of GRO - Bill Fink & Dave Miller's comment
 - Fixed sparse warnings - Reported by Andi Kleen
 - Removed unused variables
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch takes care of trafic handling related APIS.
- Interrupt Enable and disable
- Mask / Unmask Interrupt
- Traffic Interrupt handling.
- Alarm Interrupt handling.

- Changes in this submission -
        - General clean up - removed redundant includes, defines and macros.

- Changes in previous submissions -
 - General cleanup - removed unused functions and variables.
 - Use asserts where necessary - Reported by Andi Kleen
 - Fixed sparse warnings - Reported by Andi Kleen
 - Use a prefix, "__vxge" in front of hw functions to make them globally
   unique - Ben Hutchings
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch takes care of Initialization and configuration steps of
Neterion Inc's X3100 Series 10GbE PCIe I/O Virtualized Server Adapter.
- Device Initialization.
- Verification and setting of device config parameters.
- Allocation of Tx FIFO and Rx Ring descriptors (DTR).
- APIs to get various type of hw stats
- APIs to configure RTS (Receive Traffic Steering)

- Changes in this submission -
        - Include vmalloc header without which a compilation error occured
          on sparc64, ppc64 and IA64 plaforms.
	- Fixed compilation warning in register_poll, write32_upper,
          write32_lower and the special write64 functions on ppc64.
        - General cleanup - removed redundant includes and defines.

- Changes in previous submissions -
        - Add readq/writeq implementation for the driver for 32 bit systems -
          reported by Dave Miller.
- Incorporated following comments from Ben Hutchings
        - Start a comment with "/**" to make it a kernel-doc comment.
        - Use prefix, "__vxge" in front of hw functions to make them globally
          unique.
        - Fixed unnecessary clearing members of *channel just before freeing
        - Use backslashes only for macro definitions and not in multi-line
          statements.
        - Used pci_find_capability instead of redefining it.
        - Used device and revision ids that are already in pdev - no need to
          read them again.
        - Used pci_save_state() and pci_restore_state() around resets.
        - Used udelay and mdelay directly instead of wrapper.
        - In __vxge_hw_device_register_poll() reset i to 0 after the
          microsecond delay loop to commence the millisecond delay loop.
        - Corrected spelling "sapper" - should be "swapper"
        - Remove too much vertical whitespace.
        - Replaced magic numbers with appropriate macros
- Incorporated following comments from Andi Kleen [andi@firstfloor.org]
        - Reduced the arguments in functions or refactored them into smaller
        functions.
        - Allocate page sized memories used in slow path with vmalloc.
        - Use asserts where necessary.
        - Use macros instead of magic numbers.
        - Use the pci layer code instead of defining own functions
        - Remove driver wrappers such as xge_hw_device_private_set().
        - Fixed sparse warnings.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Complete Register map details of Neterion Inc's X3100 Series 10GbE PCIe I/O
  Virtualized Server Adapter.

- No change from previous submission.

- Changes in previous submissions -
- Incorporated following comments from Ben Hutchings
        - Use original macros for endian checks
        - Remove VXGE_OS_PLATFORM_* macros as they are unused.
        - Converted multiple bVALX macros into single with additional
          width parameter and renamed it to vxge_bVALn.
        - Using __packed instead of pragma pack(1)
        - Added a comment of the use of a hw swapper so driver code is
          portable (does not have to change the byte order for register
          access as well as dma operations) on different ENDIAN platforms.
        - Using the <linux/pci_regs.h> definitions instead of redefing them.
        - Using the PCI capabilities registers in <linux/pci_regs.h>
          instead of redefing them.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we use a shared legacy IRQ then our interrupt handler may be called
as soon as it is registered even though IRQs are disabled on the NIC.
Now that the legacy interrupt handler also checks for event delivery,
it may decide to schedule polling in this case.  Ensure that the NAPI
context is valid but disabled at this point.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let driver depend on HAS_IOMEM to avoid build breakage on s390:

  CC      drivers/net/ethoc.o
drivers/net/ethoc.c: In function 'ethoc_read':
drivers/net/ethoc.c:221: error: implicit declaration of function 'ioread32'
drivers/net/ethoc.c: In function 'ethoc_write':
drivers/net/ethoc.c:226: error: implicit declaration of function 'iowrite32'
drivers/net/ethoc.c: In function 'ethoc_rx':
drivers/net/ethoc.c:405: error: implicit declaration of function 'memcpy_fromio'
drivers/net/ethoc.c: In function 'ethoc_start_xmit':
drivers/net/ethoc.c:828: error: implicit declaration of function 'memcpy_toio'
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added osi_load_firmware() instead of copying same thing twice
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>

Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>

Added predef variable in add_mcs() to support predefined mcs data
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>

Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can't put 'mdio' until after we've used it in the
fsl_pq_mdio_bus_name() call.

Also fix error return values.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can't put 'mdio' until after we've used it in the
fsl_pq_mdio_bus_name() call.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allows for the removal of byteswapping in some places and
the removal of HIPQUAD (replaced by %pI4).
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/hamradio/dmascc.c:587: error: 'struct net_device' has no
member named 'set_mac_address'
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.

To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When TX aggregation becomes operational, we do a number of steps:
 1) print a debug message
 2) wake the virtual queue
 3) notify the driver

Unfortunately, 1) and 3) are only done if the driver is first to
reply to the aggregation request, it is, however, possible that the
remote station replies before the driver! Thus, unify the code for
this and call the new function ieee80211_agg_tx_operational in both
places where TX aggregation can become operational.

Additionally, rename the driver notification from
IEEE80211_AMPDU_TX_RESUME to IEEE80211_AMPDU_TX_OPERATIONAL.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

change the display of current driver status bit to user readable format
for better and easier debugging
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We shouldn't return NETDEV_TX_BUSY from the TX callback, especially
after we've mucked with the sk_buffs.  Drop the packets and return
NETDEV_TX_OK.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch restores all-in-one module build procedure for ar9170.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were claiming DMA buffers on the RX tasklet but never
upon a simple module removal.

Cc: stable@kernel.org
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k sets up a mapping table from the hardware rate index to
the rate index used by mac80211; however, we have seen some
received frames with incorrect rate indexes.  Such frames
normally get dropped with a warning in __ieee80211_rx(),
but it doesn't include enough information to track down the
error.

This patch adds a warning to hw_to_driver_rix for any lookups
that result in a rate index of -1, then returns a valid rate so
the frame can be processed.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the return type of b43_plcp_get_bitrate_idx_ofdm. If
the plcp contains an error, the function return value is 255 instead
of -1, and the packet was not dropped. This causes a warning in
__ieee80211_rx function because rate idx is out of range.

Cc: stable@kernel.org
Signed-off-by: NLorenzo Nava <navalorenx@gmail.com>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>