Previous an_disable_cap position bit31 is deprecated to be use in driver
with newer firmware.  New firmware will advertise the same capability
in bit29.

Old capability didn't allow setting more than one protocol for a
specific speed when autoneg is off, while newer firmware will allow
this and it is indicated in the new capability location.
Signed-off-by: NBodong Wang <bodong@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for query the minimum inline mode from the Firmware.
It is required for correct TX steering according to L3/L4 packet
headers.

Each send queue (SQ) has inline mode that defines the minimal required
headers that needs to be copied into the SQ WQE.
The driver asks the Firmware for the wqe_inline_mode device capability
value.  In case the device capability defined as "vport context" the
driver must check the reported min inline mode from the vport context
before creating its SQs.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each send queue (SQ) has inline mode that defines the minimal required
inline headers in the SQ WQE.
Before sending each packet check that the minimum required headers
on the WQE are copied.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit utilize the ability of ConnectX-4 to bulk read flow counters.
Few bulk counter queries could be done instead of issuing thousands of
firmware commands per second to get statistics of all flows set to HW,
such as those programmed when we offload tc filters.

Counters are stored sorted by hardware id, and queried in blocks (id +
number of counters).

Due to hardware requirement, start of block and number of counters in a
block must be four aligned.
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amir@vadai.me>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to use bulk counters, we need to have counters sorted by id.
Signed-off-by: NAmir Vadai <amir@vadai.me>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement etrhtool set_rxnfc callback to support ethtool flow spec
direct steering. This patch adds only the support of ether flow type
spec. L3/L4 flow specs support will be added in downstream patches.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of having all steering private name spaces and
steering module fields flat in mlx5_core_priv, we wrap
them in mlx5_flow_steering for better modularity and
API exposure.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the set of arguments passed to mlx5_add_flow_rule
by introducing flow_spec structure.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allow creating more than one netdev over the same PCI function, we
change the driver such that global NIC resources are created once and
later be shared amongst all the mlx5e netdevs running over that port.

Move the CQ UAR, PD (pdn), Transport Domain (tdn), MKey resources from
being kept in the mlx5e priv part to a new resources structure
(mlx5e_resources) placed under the mlx5_core device.

This patch doesn't add any new functionality.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new namespace (MLX5_FLOW_NAMESPACE_OFFLOADS) to be populated
with flow steering rules that deal with rules that have have to
be executed before the EN NIC steering rules are matched.

The namespace is located after the bypass name-space and before the
kernel name-space. Therefore, it precedes the HW processing done for
rules set for the kernel NIC name-space.

Under SRIOV, it would allow us to match on e-switch missed packet
and forward them to the relevant VF representor TIR.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amir@vadai.me>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation does not handle timeout in case of command
with callback request, and this can lead to deadlock if the command
doesn't get fw response.
Add delayed callback timeout work before posting the command to fw.
In case of real fw command completion we will cancel the delayed work.
In case of fw command timeout the callback timeout handler will be
called and it will simulate fw completion with timeout error.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous to this patch auto negotiation was reported off although it was
on by default in hardware. This patch reports the correct information to
ethtool and allows the user to toggle it on/off.

Added another parameter to set port proto function in order to pass
the auto negotiation field to the hardware.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a dedicated function to toggle port link. It should be called only
after setting a port register.
Toggle will set port link to down and bring it back up in case that it's
admin status was up.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configuring and managing HW rate limit tables.
The HW holds a table of rate limits, each rate is
associated with an index in that table.
Later a Send Queue uses this index to set the rate limit.
Multiple Send Queues can have the same rate limit, which is
represented by a single entry in this table.
Even though a rate can be shared, each queue is being rate
limited independently of others.

The SW shadow of this table holds the rate itself,
the index in the HW table and the refcount (number of queues)
working with this rate.

The exported functions are mlx5_rl_add_rate and mlx5_rl_remove_rate.
Number of different rates and their values are derived
from HW capabilities.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the SRQ API uses the obsolete mlx5_*_srq_mbox_{in,out}
structs which limit the ability to pass the SRQ attributes between
net and IB parts of the driver.

This patch changes the SRQ API so as to use auto-generated structs
and provides a better way to pass attributes which will be in use by
coming features.
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Make MODIFY_QP command input structure compliant to specification

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The driver exposes interfaces that directly relate to HW state.
Upon fatal error, consumers of these interfaces (ULPs) that rely
on completion of all their posted work-request could hang, thereby
introducing dependencies in shutdown order. To prevent this from
happening, we manage the relevant resources (CQs, QPs) that are used
by the device. Upon a fatal error, we now generate simulated
completions for outstanding WQEs that were not completed at the
time the HW was reset.

It includes invoking the completion event handler for all involved
CQs so that the ULPs will poll those CQs. When polled we return
simulated CQEs with IB_WC_WR_FLUSH_ERR return code enabling ULPs
to clean up their  resources and not wait forever for completions
upon receiving remove_one.

The above change requires an extra check in the data path to make
sure that when device is in error state, the simulated CQEs will
be returned and no further WQEs will be posted.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

If the caller specified IB_SEND_FENCE in the send flags of the work
request and no previous work request stated that the successive one
should be fenced, the work request would be executed without a fence.
This could result in RDMA read or atomic operations failure due to a MR
being invalidated. Fix this by adding the mlx5 enumeration for fencing
RDMA/atomic operations and fix the logic to apply this.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Introducing mlx5_ifc updates for upcoming ConnectX-4 features.

Needed bits and hardware structures for mlx5e netdev:
	- MLX5_CQ_PERIOD_NUM_MODES for adaptive moderation
	  support
	- QoS rate limiting
	- SQ context rate limiting
	- Auto negotiation fields in PTYS register
	- Source SQN field in flow table entry match structure
	- DCBX parameters

Needed bits and hardware structures for IB:
	- New XRQ opcodes, commands and capabilities layout
	- Extend q counters definition to support IB.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

In RoCE, the RDMA-CM needs the node guid to establish connection
between nodes.
Today, the node guid exposed to mlx5 Ethernet VFs is zero, therefore
RDMA-CM on the VF is broken.

Whenever the administrator sets a MAC for a VF, derive the node guid
from it and set it as well in the following way:
MAC: e4:1d:2d:b3:f4:01 -> node_guid: e4:1d:2d:ff:fe:b3:f4:01

Fixes: 77256579 ('net/mlx5: E-Switch, Introduce Vport...')
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow steering infrastructure is currently used only on link layer
ethernet, therefore the driver should initialize the flow steering
when the device link layer is ethernet.

In addition, add missing capability check before initializing the
namespace of NIC RX flow tables.

Fixes: 25302363 ('net/mlx5_core: Flow steering tree initialization')
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Having MLX5_CMD_OP_MAX on another file causes us to repeatedly miss
accounting new commands added to the driver and hence there're no entries
for them in debugfs. To solve that, we integrate it into the commands enum
as the last entry.

Fixes: 34a40e68 ('net/mlx5_core: Introduce modify flow table command')
Signed-off-by: NShahar Klein <shahark@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 16 reserved bytes at the end of mlx5_modify_qp_mbox_in to
match the hardware spec definition.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pkey index fields in the QP context path record are extended to 16
bits, as required by IB spec (version 1.3).
This change affects all QP commands which include path records.

To enable this change, moved the free adaptive routing flag bit
(free_ar) to the most significant byte of the QP path record.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB ...')
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Previously, we've fired all our completion callbacks straight from
our ISR.

Some of those callbacks were lightweight (for example, mlx5 Ethernet
napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over
those events could be so long, that we'll get into a hard lockup by
the system watchdog.

In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive
completion event to a per-EQ list and schedule a tasklet. In the
tasklet context we loop over all the CQs in the list and invoke the
user callback.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

If a counter has the aging flag set when created, it is added to a list
of counters that will be queried periodically from a workqueue.  query
result and last use timestamp are cached.
add/del counter must be very efficient since thousands of such
operations might be issued in a second.
There is only a single reference to counters without aging, therefore
no need for locks.
But, counters with aging enabled are stored in a list. In order to make
code as lockless as possible, all the list manipulation and access to
hardware is done from a single context - the periodic counters query
thread.

The hardware supports multiple counters per FTE, however currently we
are using one counter for each FTE.
Signed-off-by: NAmir Vadai <amirva@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When adding a flow steering rule with a counter, need to supply a
destination of type MLX5_FLOW_DESTINATION_TYPE_COUNTER, with a pointer
to a struct mlx5_fc.
Also, MLX5_FLOW_CONTEXT_ACTION_COUNT bit should be set in the action.
Signed-off-by: NAmir Vadai <amirva@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Getting packet/byte statistics on flows is done through flow counters.
Implement the firmware commands to alloc, free and query flow counters.
Signed-off-by: NAmir Vadai <amirva@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding the needed mlx5_ifc hardware bits and structs
for the following features:

* Add vport to steering commands for SRIOV ACL support
* Add mlcr, pcmr and mcia registers for dump module EEPROM
* Add support for FCS, beacon led and disable_link bits to
  hca caps
* Add CQE period mode bit in CQ context for CQE based CQ
  moderation support
* Add umr SQ bit for fragmented memory registration
* Add needed bits and caps for Striding RQ support

In-order to avoid possible future conflicts between rdma and
net-next we added all expected updates to this file for this release.
If more changes will be submitted, we plan to do it only through
one of the subsystems, probably net-next.

All updated bits in this patch will be later used in
the up-coming submissions to net-next and rdma trees.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Acked-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

All reserved fields after early_vf_enable are off by 1, since
early_vf_enable was not explicitly declared as array of size 1.

Reserved field before cqe_zip had a wrong size, it should
be 0x80 + 0x3f.

Fixes: b0844444 ("net/mlx5_core: Introduce access function to read internal timer ")
Fixes: b4ff3a36 ("net/mlx5: Use offset based reserved field names in the IFC header file")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Acked-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

CQE compression feature is meant to save PCIe bandwidth by
compressing few CQEs into smaller amount of bytes on PCIe.
CQE compression can be selectively enabled per CQ.  By default
is disabled for now and will be enabled later on.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the relevant flow steering device structs and commands to
support vport.
Update the flow steering core API to receive vport number.
Add ingress and egress ACL flow table name spaces.
Add ACL flow table support:
* ACL (Access Control List) flow table is a table that contains
only allow/drop steering rules.

* We have two types of ACL flow tables - ingress and egress.

* ACLs handle traffic sent from/to E-Switch FDB table, Ingress refers to
traffic sent from Vport to E-Switch and Egress refers to traffic sent
from E-Switch to vport.

* Ingress ACL flow table allow/drop rules is checked against traffic
sent from VF.

* Egress ACL flow table allow/drop rules is checked against traffic sent
to VF.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocating CPU rmap and add entry for each IRQ.
CPU rmap is used in aRFS to get the RX queue number
of the RX completion interrupts.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, consumers of the flow steering infrastructure can't
choose their own flow table levels and are limited to one
flow table per level. This just waste levels.
Instead, we introduce here the possibility to use multiple
flow tables in a level. The user is free to connect these
flow tables, while following the rule (FTEs in FT of level x
could only point to FTs of level y where y > x).

In addition this patch switch the order of the create/destroy
flow tables of the NIC(vlan and main).
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This API is used for modifying the flow rule destination.
This is needed for modifying the pointed flow table by the
traffic type classifier rules to point on the aRFS tables.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx5 devices (Connect-IB, ConnectX-4, ConnectX-4-LX) has a limitation
where rdma read work queue entries cannot exceed 512 bytes.
A rdma_read wqe needs to fit in 512 bytes:
- wqe control segment (16 bytes)
- rdma segment (16 bytes)
- scatter elements (16 bytes each)

So max_sge_rd should be: (512 - 16 - 16) / 16 = 30.

Cc: linux-stable@vger.kernel.org
Reported-by: NChristoph Hellwig <hch@lst.de>
Tested-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NSagi Grimberg <sagig@grimberg.me>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Now as rx-vlan offload can be disabled, packets can be received
with vlan tag not stripped, which means is_first_ethertype_ip will
return false, for that we need to check if the hardware reported
csum OK so we will report CHECKSUM_UNNECESSARY for those packets.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use ethtool -K <interface> rxvlan <on/off> to enable/disable
C-TAG vlan stripping by hardware.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add query MCIA, PMLP registers infrastructure and commands.
Add ethtool support for get_module_info() and get_module_eeprom()
callbacks.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the needed hardware command and mlx5_ifc structs for managing LED
control.
Add set_phys_id ethtool callback to support ethtool -p flag.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>