The Exynos5250 Snow Chromebook has GPIO keys for power and lid
so the SoC I/O pins have to be configured in external interrupt
mode. Currently, this is working without setting the pinctrl
lines but is better to set it explicitly instead of relying on
the previous state of the I/O pins.

The DTS snippets were taken from the downstream ChromeOS tree.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch adds MIPI-DSI and MIPI-DSI based S6E63J0X03 AMOLED panel
device nodes for Exynos3250 Rinato board.
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch adds fimd device node which is a display controller
for Exynos3250 Rinato board.
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch replaces number by macro in gpio keys for exynos3250 boards.

Cc: Youngjun Cho <yj44.cho@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch removes unnecessary property of gpio-keys node. The
gpio-keys driver doesn't use interrupts and interrupt-parent.

Cc: Youngjun Cho <yj44.cho@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch adds device tree node for hsotg to control USB 2.0 Device.
Signed-off-by: NJaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch enables hsotg and usbphy node to use USB 2.0 Device.
Signed-off-by: NJaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch adds device tree node for hsotg to control USB 2.0 Device.
Signed-off-by: NJaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

This patch adds device tree node for exynos_usbphy to use USB 2.0 Device.
Signed-off-by: NJaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Add DTS for the Hardkernel Odroid XU3. The name of the DTS file is
kept the same as the vendors naming, which means it's prefixed with
exynos5422 instead of exynos5800 as the SoC name even though it
includes the exyno5800 dtsi.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Drop the vendor-prefix from the "ti,system-power-controller" device-tree
property name.

It has been agreed to make "system-power-controller" a standard property
and to drop the vendor-prefix that is currently used by several drivers.

Note that drivers that have used "<vendor>,system-power-controller" in a
released kernel will need to support both versions.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Configure the RTC as system-power controller, which allows the system to
be powered off as well as woken up again on subsequent RTC alarms.

Note that the PMIC needs to be put in SLEEP (rather than OFF) mode to
maintain RTC power.  Specifically, this means that the PMIC
ti,pmic-shutdown-controller property must be left unset in order to be
able to wake up on RTC alarms.

Tested on BeagleBone Black (rev A5).
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable am33xx specific RTC features (e.g. PMIC control) by adding
"ti,am3352-rtc" to the compatible property of the rtc node.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The lcd0 node for am437x-sk-evm.dts contains bad LCD timings, and while
they seem to work with a quick test, doing for example blank/unblank
will give you a black display.

This patch updates the timings to the 'typical' values from the LCD spec
sheet.

Also, the compatible string is completely bogus, as
"osddisplays,osd057T0559-34ts" is _not_ a 480x272 panel. The panel on
the board is a newhaven one. Update the compatible string to reflect
this. Note that this hasn't caused any issues, as the "panel-dpi"
matches the driver.

Cc: <stable@vger.kernel.org> # v3.17+
Tested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As per the latest Data Manual, for newer samples,
the nominal voltage required for VDD_CORE at OPP_NOM can be
upto 1.06V which was 1.03V earlier.

Update the regulator max voltage constraint for SMPS7,
connected to VDD_CORE, to meet this requirement.

Document reference:
DRA74 Data Manual, SPRS857M - Dec 2012, Revised Oct 2014.
DRA72 Data Manual, SPRS906G - Dec 2012, revised Oct 2014.
Signed-off-by: NRavikumar Kattekola <rk@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The max expected voltage for VDD_GPU, connected to SMPS6, is 1.25V.
Correct regulator max voltage constraint to meet this requirement.

Document reference: DRA74 Data Manual, SPRS857M - Dec 2012,
		    Revised Oct 2014.

Fixes: c56a831c ("ARM: dts: DRA7: Add TPS659038 PMIC nodes")
Signed-off-by: NRavikumar Kattekola <rk@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Caused by a copy & paste error. Note that even with
this bug AM437x SK display still works because GPIO
mux mode is always enabled. It's still wrong to mux
somebody else's pin.

Luckily ball D25 (offset 0x238 - gpio5_8) on AM437x
isn't used for anything.

While at that, also replace a pullup with a pulldown
as that gpio should be normally low, not high.

Cc: <stable@vger.kernel.org> # v3.17+
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit f4d809ec55b6 ("ARM: dts: Fix gpmc timings for omap 2430sdp")
added GPMC timings for 2430sdp. This however broke the Ethernet
for some versions of u-boot using a different L3 clock frequency:

set_gpmc_timing_reg: GPMC error! CS5: cs_rd_off: 233 ns, 39 ticks > 31
omap-gpmc 6e000000.gpmc: failed to set gpmc timings for: ethernet

This is because the smsc91x timings from 1.1.4 u-boot overflow the
GPMC registers when booted with 1.1.3 version of u-boot.

Let's fix this issue by using the better timings from u-boot 1.1.3
as they also work on 1.1.4 and are faster.

Note that so far the attempts over the years to calculate the GPMC
timings on the SDP boards have failed probably because of the
unknown latencies added by the FPGA on the debug boards.
Reported-by: NNishanth Menon <nm@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This will enable use of physical arch timers on rk3288, where each
core comes out of reset with a different virtual offset.  Using
physical timers will help with SMP booting on coreboot and older
u-boot and should also allow suspend-resume and cpu-hotplug to work on
all firmwares.

Firmware which does initialize the cpu registers properly at boot and
cpu-hotplug can remove this property from the device tree.
Signed-off-by: NSonny Rao <sonnyrao@chromium.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

We now have the physical-timers patches lined up as a dependency in this same
branch, so we can revert the temporary disablement.

This reverts commit b77d4394.
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

Add iommus properties to the device tree nodes for the two display
controllers found on Tegra124. This will allow the display controllers
to map physically non-contiguous buffers to I/O virtual contiguous
address spaces so that they can be used for scan-out.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add iommus properties to the device tree nodes for the two display
controllers found on Tegra114. This will allow the display controllers
to map physically non-contiguous buffers to I/O virtual contiguous
address spaces so that they can be used for scan-out.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add iommus properties to the device tree nodes for the two display
controllers found on Tegra30. This will allow the display controllers to
map physically non-contiguous buffers to I/O virtual contiguous address
spaces so that they can be used for scan-out.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add the memory controller and wire up the interrupt that is used to
report errors. Provide a reference to the memory controller clock and
mark the device as being an IOMMU by adding an #iommu-cells property.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add the device tree node for the memory controller found on Tegra114
SoCs. The memory controller integrates an IOMMU (called SMMU) as well as
various knobs to tweak memory accesses by the various clients.

The old IOMMU device tree node is collapsed into the memory controller
node to more accurately describe the hardware. While this change is
incompatible, the IOMMU driver has never had any users so the change is
not going to cause any breakage.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Collapses the old memory-controller and IOMMU device tree nodes into a
single node to more accurately describe the hardware.

While this is an incompatible change there are no users of the IOMMU on
Tegra, even though a driver has existed for some time.
Signed-off-by: NThierry Reding <treding@nvidia.com>

This patch adds the APB_MISC_GP_MIPI_PAD_CTRL_0 as a pin-control bank on
Tegra124 so the new MIPI pad control group can be muxed between CSI and
DSI_B.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

vsys is the core always-on supply of the Marsboard.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

IRQ support for Broadcom's bus-axi driver bcma was merged into John
Linville's wireless tree and will show up in 3.19. This patch makes use
of this feature in the DTS file for the the BCM5301X SoCs. I left the
PCIe controller out, because this still needs some discussion.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

Add a DTS describing the Digilent ZYBO board. Similar to ZED but with
a 50MHz crystal instead of 33MHz.
Acked-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The fact that all supported boards use the same 33MHz crystal is a
co-incidence. The Zynq PS support a range of crystal freqs so the
hardcoded setting should be removed from the dtsi. Re-implement it
on the board level.

This prepares support for Zynq boards with different crystal
frequencies (e.g. the Digilent ZYBO).
Acked-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The SDMMC, SDIO and EMMC controllers use an external FIFO whose size is 256x32bit.
This patch set the corresponding fifo-depth properties for both RK3066 and RK3188.
Signed-off-by: NJulien CHAUVEAU <julien.chauveau@neo-technologies.fr>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The leds-gpio driver recently switched to the device property API. The device_node
name is no longer retrieved if the "label" devicetree property is not found.
In this case the driver tries to create entries with (null) name in
/sys/class/leds, which is wrong and generates backtrace as several gpio_leds have
the same name. Also renamed subnode "yellow" to "blue" to match the last
schematics updates.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The suspend/resume sequence on Armada XP needs to modify a number of
registers in the SDRAM controller. Therefore, this commit updates the
Armada XP Device Tree description to include the SDRAM controller
Device Tree node.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1416585613-2113-17-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

In order to support suspend/resume on Armada XP, an additional set of
registers need to be described at the MBus controller level. This
commit therefore adjusts the Device Tree of the Armada 370/XP SoC to
include those registers in the MBus controller description;
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1416585613-2113-16-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>