From: Linus Walleij <triad@df.lth.se>

This patch enables support for ALi ISA bridges when we run the smcinit
code.  It is needed to properly configure some Toshiba laptops.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the STIR421x case, when the firmware upload fails, we need to
unregister_netdev. Otherwise we hit a BUG on free_netdev(), if sysfs
is enabled.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ixgb driver is using pci_alloc_consistent, thus is should also use
pci_set_consistent_dma_mask.  This allows the driver to work on SGI
systems.

In case of an error during probing it should also disable the device again.
Signed-off-by: NAndreas Schwab <schwab@suse.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Sky2 driver will oops referencing bad memory if used on
a dual port card.  The problem is accessing past end of
MIB counter space.

Applies for both 2.6.17 and 2.6.16 (with fuzz)
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

After resetting the hardware on a tx_timeout, call netif_wake_queue()
only if we have free tx descriptors.

Also, attempt to recover if mv643xx_eth_start_xmit() is called when
there are fewer free tx descriptors than expected.

The BUG_ON() call we are replacing was hit on a tx_timeout that
called netif_wake_queue(), indirectly via netif_device_attach(),
even though we did not have enough free tx descriptors.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix the tx interrupt handler to free completed tx descriptors even
when NAPI is enabled.  Otherwise, the tx queue would fill up resulting
in poor performance and "NETDEV WATCHDOG: <iface>: transmit timed out"
messages.
Signed-off-by: NBrent Cook <bcook@bpointsys.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If CONFIG_HOTPLUG=n, gcc doesn't like some __initdata to be const (rodata)
and other __initdata not const, so make the non-const __initdata const.

gcc errors:
drivers/net/bnx2.c:66: error: version causes a section type conflict
drivers/net/starfire.c:338: error: version causes a section type conflict
drivers/net/typhoon.c:137: error: version causes a section type conflict
drivers/net/natsemi.c:241: error: version causes a section type conflict
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove drivers/net/hydra.h which is both unused and covered by a 4 clause
BSD licence (not by the UCB).
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-By: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NRoger Luethi <rl@hellgate.ch>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

Disable default tx pause frame support.
The b44 controller has a bug that generates excessive tx pause
frames.
Signed-off-by: NGary Zambrano <zambrano@broadcom.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Patch suggested by Yang Wu (pin xue <pinxue@gmail.com>).
Signed-off-by: NRoger Luethi <rl@hellgate.ch>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes the problem of some Dlink cards picking the wrong
driver.  It looks like these cards use Yukon 1 chipset, not Yukon 2.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The in-kernel Sangoma drivers are both not compiling and marked as BROKEN
since at least kernel 2.6.0.

Sangoma offers out-of-tree drivers, and David Mandelstam told me Sangoma
does no longer maintain the in-kernel drivers and prefers to provide them
as a separate installation package.

This patch therefore removes these drivers.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Speed up SRAM read and write functions if possible by using MMIO
instead of config. cycles. With this change, the post reset signature
done at the end of D3 power change must now be moved before the D3
power change.

IBM reported a problem on powerpc blades during ethtool self test that
was caused by the memory test taking excessively long. Config.  cycles
are very slow on powerpc and the memory test can take more than 10
seconds to complete using config. cycles.

David Miller informed me that an earlier version of the patch caused
problems on sparc64 systems with built-in tg3 chips. This version
fixes the problem by excluding all SUN built-in tg3 chips from doing
MMIO SRAM access.

TG3_FLAG_EEPROM_WRITE_PROT is also set unconditionally when
TG3_FLG2_SUN_570X is set. This should be sane as all SUN chips are
built-in and do not require Vaux switching.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kill the TG3_FLAG_NO_{TX|RX}_PSEUDO_CSUM flags because they are not
very useful. This will free up some bits for new flags.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables support for the Sigmatel's STIR421x IrDA chip.
Once patched with Sigmatel's firmware, this chip "almost" follows the
USB-IrDA spec. Thus this patch is against irda-usb.[ch].

The code has been tested by Nick Fedchik on an STIR4210 chipset based
dongle.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch integrates the smcinit code into the smsc-ircc driver.
Some laptops have their smsc-ircc chip not properly configured by the
BIOS and needs some preconfiguration. Currently, this can be done from
userspace with smcinit, a utility that comes with the irda-utils
package. It messes with ioports and PCI settings, from userspace.  Now
with this patch, if we happen to be on one of the known to be faulty
laptops, we preconfigure the chip from the driver.

Patch from Linus Walleij <triad@df.lth.se>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a memory leak (buf wasn't freed) spotted by the
Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set .name in netconsole's struct console to identify the
struct's owner.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes some uneeded rebuilds under drivers/net/chelsio after moving
the source tree. The makefiles used $(TOPDIR) for include paths, which
is unnecessary. Changed to use relative paths.

Compile tested, produces byte-identical code to the previous makefiles.
Signed-off-by: NCarl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Also cleans up some nearby whitespace problems.
Signed-off-by: NSegher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

WARNING: "__you_cannot_kzalloc_that_much" [drivers/net/arcnet/com90xx.ko] undefined!

We're trying to allocate negative amounts of memory..
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Undo commit 100c4673

MMIOs timeout more quickly that PCI config cycles and some
of these SRAM accesses can take a very long time, triggering
the MMIO limits on some sparc64 PCI controllers and thus
resulting in bus timeouts and bus errors.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "3c59x: use mii_check_media" patch introduced a netif_carrier_off in
vortex_up.  10base2 stoped working because of this.  This is removed.

Tx/Rx reset is back in vortex_up because the 3c900B-Combo stops working after
changing from half duplex to full duplex when Tx/Rx reset is done with
vortex_timer.

Also brought back some mii stuff to be sure that it does not break something
else.

Thanks to Pete Clements <clem@clem.clem-digital.net> for reporting and testing.
Signed-off-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The pre-2.6.16 patch "3c59x collision statistics fix" accidentally caused
vortex_error() to not run iowrite16(TxEnable, ioaddr + EL3_CMD) if we got a
maxCollisions interrupt but MAX_COLLISION_RESET is not set.

Thanks to Pete Clements <clem@clem.clem-digital.net> for reporting and testing.
Acked-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).

And __setup() is used in obsolete_checksetup().

	start_kernel()
		-> parse_args()
			-> unknown_bootoption()
				-> obsolete_checksetup()

If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.

If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func().  If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].

Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.

This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

kconfig sanitized around drivers/net
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Instead of the DEV_OK macro, drivers should use pcmcia_dev_present().
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Instead of the two status values struct pcmcia_device->p_state and state,
use descriptive bitfields. Most value-checking in drivers was invalid, as
the core now only calls the ->remove() (a.k.a. detach) function in case the
attachement _and_ configuration was successful.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Remove the unused DEV_RELEASE_PENDING flag, and move the DEV_SUSPEND flag
into the p_dev structure, and make use of it at the core level.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Most of the driver initialization isn't done in the .probe function, but in
the internal _config() functions. Make them return a value, so that .probe
can properly report whether the probing of the device succeeded or not.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

dev_link_t * and client_handle_t both mean struct pcmcai_device * by now.
Therefore, remove all such indirections.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Embed dev_link_t into struct pcmcia_device(), as they basically address the
same entity. The actual contents of dev_link_t will be cleaned up step by step.
This patch includes a bugfix from and signed-off-by Andrew Morton.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

As we do not allow setting Vcc in the pcmcia core, and Vpp1 and
Vpp2 can only be set to the same value, a lot of code can be
streamlined.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Handle the _modifying_ operation sm91c92_cs requires in
pcmcia_modify_configuration, so that the only remaining users
of pcmcia_release_configuration() are within the pcmcia core
module.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>