Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 12 8月, 2010 1 次提交
    • A
      mmc: add erase, secure erase, trim and secure trim operations · dfe86cba
      由 Adrian Hunter 提交于 
      SD/MMC cards tend to support an erase operation.  In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.

SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.

"erase_size" is the minimum size, in bytes, of an erase operation.  For
MMC, "erase_size" is the erase group size reported by the card.  Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector.  For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.

SD/MMC cards can erase an arbitrarily large area up to and
including the whole card.  When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:

    1. A single erase command will make all other I/O on the card
       wait.  This is not a problem if the whole card is being erased, but
       erasing one partition will make I/O for another partition on the
       same card wait for the duration of the erase - which could be a
       several minutes.

    2. To be able to inform the user of erase progress.

    3. The erase timeout becomes too large to be very useful.
       Because the erase timeout contains a margin which is multiplied by
       the size of the erase area, the value can end up being several
       minutes for large areas.

"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.

For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.

For SD, "preferred_erase_size" is the allocation unit size specified by
the card.

"preferred_erase_size" is in bytes.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NJens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      dfe86cba
  3. 11 8月, 2010 6 次提交
  5. 28 5月, 2010 3 次提交
  7. 14 4月, 2010 1 次提交
    • D
      ARM: MXC: mxcmmc: work around a bug in the SDHC busy line handling · 3fcb027d
      由 Daniel Mack 提交于 
      MX3 SoCs have a silicon bug which corrupts CRC calculation of
multi-block transfers when connected SDIO peripheral doesn't drive the
BUSY line as required by the specs.

One way to prevent this is to only allow 1-bit transfers.

Another way is playing tricks with the DMA engine, but this isn't
mainline yet. So for now, we live with the performance drawback of 1-bit
transfers until a nicer solution is found.

This patch introduces a new host controller callback 'init_card' which
is for now only called from mmc_sdio_init_card().
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
      3fcb027d
  9. 30 3月, 2010 1 次提交
    • T
      include cleanup: Update gfp.h and slab.h includes to prepare for breaking... · 5a0e3ad6
      由 Tejun Heo 提交于 
      include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
      5a0e3ad6
  11. 25 3月, 2010 1 次提交
    • A
      mmc: fix incorrect interpretation of card type bits · 7198f3c9
      由 Adrian Hunter 提交于 
      In the extended CSD register the CARD_TYPE is an 8-bit value of which the
upper 6 bits were reserved in JEDEC specifications prior to version 4.4.
In version 4.4 two of the reserved bits were designated for identifying
support for the newly added High-Speed Dual Data Rate.  Unfortunately the
mmc_read_ext_csd() function required that the reserved bits be zero
instead of ignoring them as it should.

This patch makes mmc_read_ext_csd() ignore the CARD_TYPE bits that are
reserved or not yet supported.  It also stops the function jumping to the
end as though an error occurred, when it is only warns that the CARD_TYPE
bits (that it does interpret) are invalid.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      7198f3c9
  13. 13 3月, 2010 1 次提交
  15. 07 3月, 2010 5 次提交
  17. 12 1月, 2010 1 次提交
  19. 18 12月, 2009 2 次提交
  21. 16 12月, 2009 2 次提交
    • B
      mmc: add module parameter to set whether cards are assumed removable · bd68e083
      由 Ben Hutchings 提交于 
      Some people run general-purpose distribution kernels on netbooks with
a card that is physically non-removable or logically non-removable
(e.g. used for /home) and cannot be cleanly unmounted during suspend.
Add a module parameter to set whether cards are assumed removable or
non-removable, with the default set by CONFIG_MMC_UNSAFE_RESUME.

In general, it is not possible to tell whether a card present in an MMC
slot after resume is the same that was there before suspend.  So there are
two possible behaviours, each of which will cause data loss in some cases:

CONFIG_MMC_UNSAFE_RESUME=n (default): Cards are assumed to be removed
during suspend.  Any filesystem on them must be unmounted before suspend;
otherwise, buffered writes will be lost.

CONFIG_MMC_UNSAFE_RESUME=y: Cards are assumed to remain present during
suspend.  They must not be swapped during suspend; otherwise, buffered
writes will be flushed to the wrong card.

Currently the choice is made at compile time and this allows that to be
overridden at module load time.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: Wouter van Heyst <larstiq@larstiq.dyndns.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      bd68e083
    • A
      sdio: rework cis tuple parsing · 4ec64960
      由 Albert Herranz 提交于 
      Rework the current CIS tuple parsing code, reusing the existing
infrastructure and providing an easy way to add new CISTPL_FUNCE parsers
by TPLFE_TYPE.

Valid known CIS tuples are now silently queued for the SDIO function
driver when not parsed/processed (-EILSEQ) by the SDIO core.  Unknown CIS
tuples (-ENOENT) are queued too for the SDIO function driver without
aborting the initialization, but emit a warning in the kernel log.

CISTPL_FUNCE tuples can be "whitelisted" now by adding a matching entry to
the cis_tpl_funce_list table.
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Acked-by: NPierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      4ec64960
  23. 08 10月, 2009 1 次提交
  25. 02 10月, 2009 2 次提交
  27. 23 9月, 2009 13 次提交