- 20 10月, 2012 10 次提交
-
-
由 Stanislaw Gruszka 提交于
We skip compensate calculation for non 11b rates on 2.4GHz band. I do not see that on vendor driver (2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO). Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com> Acked-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Based on AsicAdjustTxPower function from vendor driver (2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO) limit per rate TX power values we program into TX_PWR_CFG_ registers. Note that on some configurations (devices/rates) is allowed to use bigger values than 0xc, but we use safe maximum value for now. Further work need to be done to allow use bigger values than 0xc. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
TX power delta can be negative. TX_PWR_CFG_ registers allow to set delta only in range between 0 dBm and 15 dBm (4 bits for each rate). Se we need to use BBP_R1 to configure negative deltas. Not utilize +6 dBm increasing BBP_R1 option for safety reason. For now, this can be used for devices, which export maximum allowed TX power value. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com> Acked-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sven Eckelmann 提交于
All defines for REG_WRITE in Atheros wireless drivers use the order "ah", "register" and "value". hw.c is the only file using the order "ah", "value" and "register". drivers/net/wireless/ath/ath9k/hw.h:#define REG_WRITE(_ah, _reg, _val) \ drivers/net/wireless/ath/key.c:#define REG_WRITE(_ah, _reg, _val) (common->ops->write)(_ah, _val, _reg) This inconsistent definition can easily lead to implementation errors. The modification doesn't change the behavior of the driver or the generated code. Signed-off-by: NSven Eckelmann <sven@narfation.org> Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Andy Shevchenko 提交于
The patch changes a bit trace output format in the rtl_cam_program_entry() to print prefix and the actual data on the same line. Moreover the %*phC outputs each byte as 2 hex digits, which is slightly different to the original %x. Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> ACKed-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Carpenter 提交于
In ezusb_read_ltv() we had a comparison "(bufsize < 0)" which was never true because bufsize was unsigned. I looked at the implications of that. If we passed a negative number to ezusb_access_ltv() then it would be used as the size parameter of the memcpy() because that function uses min_t(int, exp_len, ans_size). But fortunately when I looked at the callers, bufsize is not controlled by the user and it's never negative. So these signedness mistakes have no impact. I removed the always false check from ezusb_read_ltv() and I changed the types in ezusb_access_ltv() and made the variables unsigned. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Peter Senna Tschudin 提交于
This patch remove a semicolon after if(...) that is preventing the error check to work correctly. Removing this semicolon will change the code behavior, but this is intended. The semantic patch that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r1@ position p; @@ if (...);@p @script:python@ p0 << r1.p; @@ // Emacs org-mode output cocci.print_main("", p0) cocci.print_secs("", p0) // </smpl> Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
BT_OP_SCAN is applicable only for pre-MCI WLAN/BT combo chips and using it for MCI-based cards is incorrect. Fix this by cleaning up its usage. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
The BCM4706 has two PCIe host controller on the bcma bus. For PCIe client mode it is assumed that there is only one PCIe controller so the PCIe driver, like b43 and brcmsmac are accessing the first PCIe controller when they want to issue a operation on the host controller. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 18 10月, 2012 2 次提交
-
-
由 Arend van Spriel 提交于
The include file linux/ieee80211.h contains three definitions for the same thing in enum ieee80211_eid due to historic changes: /* Information Element IDs */ enum ieee80211_eid { : WLAN_EID_WPA = 221, WLAN_EID_GENERIC = 221, WLAN_EID_VENDOR_SPECIFIC = 221, : }; The standard refers to this as "vendor specific" element so the other two definitions are better not used. This patch changes the wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC. Cc: Jouni Malinen <j@w1.fi> Cc: Dan Williams <dcbw@redhat.com> Cc: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl] Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex] Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> [ipw2x00] Signed-off-by: NArend van Spriel <arend@broadcom.com> [change libipw as well] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
The next patch will introduce a flag that is set by default in cfg80211 so drivers and mac80211 need to use |= to set features they have so that they don't clear the already-set feature. We could set the flag in wiphy_register() instead of wiphy_new() to avoid this patch, but then the drivers couldn't *unset* flags they don't want to use even though the implementation is generic. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 16 10月, 2012 8 次提交
-
-
由 Emmanuel Grumbach 提交于
This can happen when we shut down suddenly an interface. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
Once in bus enumeration is enough, no need to print it again when the op_mode loads. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
Doing the opposite is wrong, the SCD wouldn't like someone to clear its data while the queue is still active. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
Instead of hardcoding the expression, use the macro provided in the previous patch. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
When we disable a queue, we don't want the SCD to remember anything about this queue (what packet was transmitted but not acked, what packed was acked etc...). Wipe out all this data in its SRAM. Constify the arguments to iwl_write_targ_mem_dwords on the way. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Remove a number of variables that are assigned, but not used. Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
When tracing in iwlwifi, we get all data. Most of the time, we don't need it, and it just takes up a lot of extra space in the trace. Make this optional by recording the data into two separate trace events if it is needed. Without it, record only the content of non-data and EAPOL TX frames. As a result, tracing without the data tracepoints will record meta information including the 802.11 headers for all frames but will not record the contents of data frames to reduce trace overhead. Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
When warning about a command that is too large, print out the command name/ID to help figure out which place is attempting to send a command that is too large. Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 09 10月, 2012 6 次提交
-
-
由 Ronald Wahl 提交于
This patch fixes the following bug: usb 1-1.1: restart device (8) BUG: sleeping function called from invalid context at drivers/usb/core/urb.c:654 in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper (usb_poison_urb+0x1c/0xf8) (usb_poison_anchored_urbs+0x48/0x78) (carl9170_usb_handle_tx_err+0x128/0x150) (carl9170_usb_reset+0xc/0x20) (carl9170_handle_command_response+0x298/0xea8) (carl9170_usb_tasklet+0x68/0x184) (tasklet_hi_action+0x84/0xdc) this only happens if the device is plugged in an USB port, the driver is loaded but inactive (e.g. the wlan interface is down). If the device is active everything is fine. Signed-off-by: NRonald Wahl <ronald.wahl@raritan.com> Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wei Yongjun 提交于
The dereference should be moved below the NULL test. dpatch engine is used to auto generate this patch. (https://github.com/weiyj/dpatch) Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
Driver gets LINK_LOST, DEAUTHENTICATED and DISASSOCIATED events from firmware when connection is lost in different scenarios. Currently we are using common code WLAN_REASON_DEAUTH_LEAVING for these cases. This patch adds support to parse an actual reason code from firmware event body and send it to cfg80211. WLAN_REASON_DEAUTH_LEAVING code is used if deauth is initiated by our device. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
This patch adds support to send correct reason code got from firmware when association attempt fails. Also, the error message displayed for association failure due to network incompatibility is modified. Current message "cannot find ssid.." misleads user. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
scan_processing flag should be reset when scan request is failed due to some reasons Ex. memory allocation failure etc. Otherwise further scan requests will be blocked. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bing Zhao 提交于
There are cases we cannot scan when request is received. For example, during WPA group key negociation the scan request will be blocked. We should return an error code to cfg80211 because cfg80211_scan_done will never be called. Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NPaul Stewart <pstew@chromium.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 06 10月, 2012 4 次提交
-
-
由 Daniel Golle 提交于
This should be register 66 instead of 62. (probably happened by copy&past'ing from the lines below) Signed-off-by: NDaniel Golle <dgolle@allnet.de> Acked-by: NGertjan van Wingerde <gwingerde@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
Using ieee80211_free_txskb for tx frames is required, since mac80211 clones skbs for which socket tx status is requested. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Cc: stable@vger.kernel.org Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
Ensure that drv_start() always returns true, as a failing hw start usually eventually leads to crashes when there's still a station entry present. Call a power-on reset after a resume and after a hw reset failure to bring the hardware back to life again. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
ath_pci_aspm_init is only called on card init, so PCI registers get reset after a suspend/resume cycle. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 29 9月, 2012 10 次提交
-
-
由 Sujith Manoharan 提交于
The WLAN/BT weights have to set correctly before BTCOEX is initialized. Currently, this is not done for all chips in the AR9003 family. This patch fixes this issue by setting the weights in the init path. While at it, rename ar9462_wlan_weights to mci_wlan_weights since it is common to both AR9462 and AR9565. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wei Yongjun 提交于
Convert cpu_to_le16(le16_to_cpu(E1) + E2) to use le16_add_cpu(). dpatch engine is used to auto generate this patch. (https://github.com/weiyj/dpatch) Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
Once hostsleep is activated, this patch takes care of not dropping packets in RX reorder table. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sven Eckelmann 提交于
Interrupts with the sync_cause AR_INTR_SYNC_HOST1_FATAL and AR_INTR_SYNC_HOST1_PERR have to be handled using a chip reset. Otherwise a interrupt storm with unhandled interrupts will cause a hang or crash of the machine. Signed-off-by: NSven Eckelmann <sven@narfation.org> Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Arend van Spriel 提交于
The function brcmf_update_prof() only add complexity that is not needed. Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Arend van Spriel 提交于
The function brcmf_read_prof() provided access to fields with brcmf_cfg80211_profile structure using a field id, but the calling function can easily access that structure directly. This patch removes the function. Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Arend van Spriel 提交于
Renamed structure to brcmf_cfg80211_info as it is not really a private structure since it is exposed in header file. Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hante Meuleman 提交于
This patch adds support for host AP mode. Reviewed-by: NArend Van Spriel <arend@broadcom.com> Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NHante Meuleman <meuleman@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Arend van Spriel 提交于
The structures brcmf_cfg80211_dev and brcmf_cfg80211_iface are only adding complexity and provide no additional value. These have been removed in this patch. Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Arend van Spriel 提交于
The low-level driver part interfaces with wl_cfg80211 part using brcmf_cfg80211_dev structure as handle. As brcmf_cfg80211_priv is defined in interface it is more efficient to use that as handle in function calls. Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-