We skip compensate calculation for non 11b rates on 2.4GHz band. I do
not see that on vendor driver
(2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO).
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Based on AsicAdjustTxPower function from vendor driver
(2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO)
limit per rate TX power values we program into TX_PWR_CFG_ registers.

Note that on some configurations (devices/rates) is allowed to use
bigger values than 0xc, but we use safe maximum value for now. Further
work need to be done to allow use bigger values than 0xc.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX power delta can be negative. TX_PWR_CFG_ registers allow to set delta
only in range between 0 dBm and 15 dBm (4 bits for each rate). Se we
need to use BBP_R1 to configure negative deltas.

Not utilize +6 dBm increasing BBP_R1 option for safety reason. For now,
this can be used for devices, which export maximum allowed TX power
value.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All defines for REG_WRITE in Atheros wireless drivers use the order "ah",
"register" and "value". hw.c is the only file using the order "ah", "value" and
"register".

drivers/net/wireless/ath/ath9k/hw.h:#define REG_WRITE(_ah, _reg, _val) \
drivers/net/wireless/ath/key.c:#define REG_WRITE(_ah, _reg, _val) (common->ops->write)(_ah, _val, _reg)

This inconsistent definition can easily lead to implementation errors. The
modification doesn't change the behavior of the driver or the generated code.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch changes a bit trace output format in the rtl_cam_program_entry() to
print prefix and the actual data on the same line. Moreover the %*phC outputs
each byte as 2 hex digits, which is slightly different to the original %x.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
ACKed-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In ezusb_read_ltv() we had a comparison "(bufsize < 0)" which was never
true because bufsize was unsigned.  I looked at the implications of
that.  If we passed a negative number to ezusb_access_ltv() then it
would be used as the size parameter of the memcpy() because that
function uses min_t(int, exp_len, ans_size).

But fortunately when I looked at the callers, bufsize is not controlled
by the user and it's never negative.  So these signedness mistakes have
no impact.

I removed the always false check from ezusb_read_ltv() and I changed the
types in ezusb_access_ltv() and made the variables unsigned.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch remove a semicolon after if(...) that is preventing the
error check to work correctly. Removing this semicolon will change the
code behavior, but this is intended.

The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r1@
position p;
@@
if (...);@p

@script:python@
p0 << r1.p;
@@
// Emacs org-mode output
cocci.print_main("", p0)
cocci.print_secs("", p0)
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BT_OP_SCAN is applicable only for pre-MCI WLAN/BT combo chips
and using it for MCI-based cards is incorrect. Fix this by
cleaning up its usage.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The BCM4706 has two PCIe host controller on the bcma bus. For PCIe
client mode it is assumed that there is only one PCIe controller so the
PCIe driver, like b43 and brcmsmac are accessing the first PCIe
controller when they want to issue a operation on the host controller.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:

    /* Information Element IDs */
    enum ieee80211_eid {
        :
        WLAN_EID_WPA = 221,
        WLAN_EID_GENERIC = 221,
        WLAN_EID_VENDOR_SPECIFIC = 221,
        :
    };

The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:

/* Information Element IDs */
enum ieee80211_eid {
    :
    WLAN_EID_WPA = 221,
    WLAN_EID_GENERIC = 221,
    WLAN_EID_VENDOR_SPECIFIC = 221,
    :
};

The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.

Cc: Jouni Malinen <j@w1.fi>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> [ipw2x00]
Signed-off-by: NArend van Spriel <arend@broadcom.com>
[change libipw as well]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The next patch will introduce a flag that is set
by default in cfg80211 so drivers and mac80211
need to use |= to set features they have so that
they don't clear the already-set feature.

We could set the flag in wiphy_register() instead
of wiphy_new() to avoid this patch, but then the
drivers couldn't *unset* flags they don't want to
use even though the implementation is generic.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This can happen when we shut down suddenly an interface.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Once in bus enumeration is enough, no need to print it
again when the op_mode loads.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Doing the opposite is wrong, the SCD wouldn't like someone
to clear its data while the queue is still active.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of hardcoding the expression, use the macro
provided in the previous patch.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we disable a queue, we don't want the SCD to remember anything
about this queue (what packet was transmitted but not acked, what
packed was acked etc...).
Wipe out all this data in its SRAM.

Constify the arguments to iwl_write_targ_mem_dwords on the way.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove a number of variables that are assigned, but not used.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When tracing in iwlwifi, we get all data. Most of
the time, we don't need it, and it just takes up
a lot of extra space in the trace.

Make this optional by recording the data into two
separate trace events if it is needed. Without it,
record only the content of non-data and EAPOL TX
frames.

As a result, tracing without the data tracepoints
will record meta information including the 802.11
headers for all frames but will not record the
contents of data frames to reduce trace overhead.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When warning about a command that is too large,
print out the command name/ID to help figure
out which place is attempting to send a command
that is too large.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The device had an undocumented "feature": it can provide a sequence of
spurious link-down status data even if the link is up all the time.
A sequence of 10 was seen so update the link state only after the device
reports the same link state 20 times.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Reported-by: NMichael Leun <lkml20120218@newton.leun.net>
Tested-by: NMichael Leun <lkml20120218@newton.leun.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some device types support a form of power management in which
the device suggests to the host that the device may be suspended
now. Support for that is best located in usbnet.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on patch from Matthew Garrett <mjg@redhat.com> (https://lkml.org/lkml/2011/11/11/168).

http://driveragent.com/archive/30421/7-0-14 indicates that ASPM is
disabled on the 250 and 260. Duplicate for sanity.

Fixes random RX engine hangs I experienced with JMC250 on Clevo W270HU.
Signed-off-by: NKevin Baradon <kevin.baradon@gmail.com>
Cc: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We nowdays copy the buffer and free fw->data, so make the debug printk use
the right thing.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch originated from Hiroaki SHIMODA but has been modified
by Intel with some minor cleanups and additional commit log text.

Denys Fedoryshchenko and others reported Tx stalls on e1000e with
BQL enabled.  Issue was root caused to hardware delays. They were
introduced because some of the e1000e hardware with transmit
writeback bursting enabled, waits until the driver does an
explict flush OR there are WTHRESH descriptors to write back.

Sometimes the delays in question were on the order of seconds,
causing visible lag for ssh sessions and unacceptable tx
completion latency, especially for BQL enabled kernels.

To avoid possible Tx stalls, change WTHRESH back to 1.

The current plan is to investigate a method for re-enabling
WTHRESH while not harming BQL, but those patches will be later
for net-next if they work.

please enqueue for stable since v3.3 as this bug was introduced in
commit 3f0cfa3b
Author: Tom Herbert <therbert@google.com>
Date:   Mon Nov 28 16:33:16 2011 +0000

    e1000e: Support for byte queue limits

    Changes to e1000e to use byte queue limits.
Reported-by: NDenys Fedoryshchenko <denys@visp.net.lb>
Tested-by: NDenys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: NHiroaki SHIMODA <shimoda.hiroaki@gmail.com>
CC: eric.dumazet@gmail.com
CC: therbert@google.com
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An SKB paged fragment can consist of a compound page with order > 0.
However the netchannel protocol deals only in PAGE_SIZE frames.

Handle this in netbk_gop_frag_copy and xen_netbk_count_skb_slots by
iterating over the frames which make up the page.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If vxlan is created and the ifindex is passed; there are two cases which
are incorrectly handled by the existing code. The ifindex could be zero
(i.e. no device) or there could be no device with that ifindex.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vxlan was trying to use postpull_rcsum to allow receive checksum
offload to work on drivers using CHECKSUM_COMPLETE method. But this
doesn't work correctly. Just force full receive checksum on received
packet.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tell upper layer protocols to allocate skb with additional headroom.
This avoids allocation and copy in local packet sends.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VXLAN bases source UDP port based on flow to help the
receiver to be able to load balance based on outer header flow.

This patch restricts the port range to the normal UDP local
ports, and allows overriding via configuration.

It also uses jhash of Ethernet header when looking at flows
with out know L3 header.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When tunnelling a skb, associate it with the tunnel socket.
This allows parameters set on tunnel socket (like multicast loop
flag), to be picked up by ip_output.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Select source address for VXLAN packet based on route destination
and don't lie to route code. VXLAN is not GRE.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shift was wrong direction causing packets to hash based on
other parts of the ethernet header, not the address.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move code to find destination to a small function.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ensure that of_mdio_find_bus() matches the prototype in the header (and
stop sparse complaining) by including the header with the prototype.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We're trying to fill a 64 bit bitmap but only the lower 30 shifts work
because the shift wraps around.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On certain platforms, BE hardware could  falsely indicate UE.
For BE family of NICs, do not set hw_error based on the UE bits.
If there was a real fatal error, the corresponding h/w block will
automatically go offline and stop traffic.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fengguang reported a kernel build failure as following:
drivers/built-in.o: In function `pch_gbe_ioctl':
pch_gbe_main.c:(.text+0x510370): undefined reference to `pch_ch_control_write'
pch_gbe_main.c:(.text+0x510393): undefined reference to `pch_ch_control_write'
pch_gbe_main.c:(.text+0x5103b3): undefined reference to `pch_ch_control_write'
...

It's a regression by commit da158646. The root cause is that
the CONFIG_PPS is not set there, consequently CONFIG_PTP_1588_CLOCK
can not be set anyway, which finally causes ptp_pch and pch_gbe_main
build failures.

As David prefers to use *select* to fix such module co-dependency issues,
this patch explicitly selects all the possible dependencies of PCH_PTP.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Reviewed-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NHaicheng Li <haicheng.lee@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i218 is the next-generation LOM that will be available on systems with the
Lynx Point LP Platform Controller Hub (PCH) chipset from Intel.  This patch
provides the initial support of those devices.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>