- 05 7月, 2008 1 次提交
-
-
由 Sascha Hauer 提交于
This patch removes the statically initialized tables from the i.MX serial driver and makes the driver fully dependent on the information provided by the platform_device. Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
- 06 3月, 2008 1 次提交
-
-
由 Harvey Harrison 提交于
__FUNCTION__ is gcc-specific, use __func__ Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 29 1月, 2008 1 次提交
-
-
由 Adrian Bunk 提交于
"make dep" is no longer required in kernel 2.6, but was still mentioned in some places. Signed-off-by: NAdrian Bunk <bunk@kernel.org> Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
-
- 27 11月, 2007 1 次提交
-
-
由 Pavel Pisa 提交于
The AITC code did not allow to start kernel, if bootloader manipulates with interrupt level mask. The change ensures, that NIMASK is initialized into correct state and that interrupts enable registers are cleared. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 05 10月, 2007 1 次提交
-
-
由 Thomas Renninger 提交于
Signed-off-by: NThomas Renninger <trenn@suse.de> Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Bryan Wu <bryan.wu@analog.com> Cc: Andi Kleen <ak@suse.de> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mundt <lethal@linux-sh.org> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NDave Jones <davej@redhat.com>
-
- 25 9月, 2007 1 次提交
-
-
由 Pavel Pisa 提交于
The patch enables to define MMC host get_ro() method through platform data. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
-
- 30 8月, 2007 1 次提交
-
-
由 Pavel Pisa 提交于
During GPIO testing on PiMX1 board there has been revealed problem with some pins input functions. The GIUS bit has to be set for inputs to work reliably too. It is surprising that input worked on some inputs with incorrect setup before. DR is not mandatory, but it ensures stable constant level on internal traces. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 23 8月, 2007 1 次提交
-
-
由 Pavel Pisa 提交于
The pins for GPIO should be provided as plain number build as (GPIO_PORTx + pin_number). But to setup the output GPIO_GIUS and GPIO_DR have to be specified in mode to route right value to the pin. This is a fix, it should go to 2.6.23 Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 22 7月, 2007 1 次提交
-
-
由 Thomas Gleixner 提交于
We need to make sure, that the clockevent devices are resumed, before the tick is resumed. The current resume logic does not guarantee this. Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock event devices before resuming the tick / oneshot functionality. Fixup the existing users. Thanks to Nigel Cunningham for tracking down a long standing thinko, which affected the jinxed VAIO. [akpm@linux-foundation.org: xen build fix] Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Cc: john stultz <johnstul@us.ibm.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 12 7月, 2007 2 次提交
-
-
由 Pavel Pisa 提交于
Support clock event source based on i.MX general purpose timer in free running timer mode. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: NThomas Gleixner <tglx@linutronix.de> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Pavel Pisa 提交于
Support for generic input output for MX1 family. The implementation prevents allocation of one pin by two users, but does not store pointer to the user description permanently, because this solution would have bigger memory overhead. The simple way to integrate code with per BSP pins setup and allocation is required else all GPIO registration checking is useless. The function imx_gpio_setup_multiple_pins() can be used for this purpose in future. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 31 5月, 2007 1 次提交
-
-
由 Russell King 提交于
The following patch fixes these section mismatch warnings: WARNING: arch/arm/mach-at91/built-in.o(.text+0xdf4): Section mismatch: reference to .init.data:dk_nand_partition (between 'nand_partitions' and 'at91_leds_event') WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (after 'nand_partitions') WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (between 'nand_partitions' and 'ads7843_pendown_state') WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (after 'nand_partitions') WARNING: arch/arm/mach-at91/built-in.o(.text+0xc28): Section mismatch: reference to .init.data:kb9202_nand_partition (after 'nand_partitions') WARNING: arch/arm/mach-footbridge/built-in.o(.text+0xaa4): Section mismatch: reference to .init.data:cats_pci (between 'cats_pci_init' and 'ebsa285_leds_event')WARNING: arch/arm/mach-ixp2000/built-in.o(.text+0xb54): Section mismatch: reference to .init.text:ixp2000_init_irq (between 'ixdp2x00_init_irq' and 'ixdp2x00_irq_handler') WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x670): Section mismatch: reference to .init.text:ixp23xx_pci_common_init (between 'ixp23xx_pci_slave_init' and 'ixp23xx_pci_scan_bus') WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x890): Section mismatch: reference to .init.text:ixp23xx_init_irq (between 'ixdp2351_init_irq' and 'roadrunner_pci_preinit') WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x9a8): Section mismatch: reference to .init.text:ixp23xx_pci_preinit (after 'roadrunner_pci_preinit') WARNING: arch/arm/mach-imx/built-in.o(__ksymtab+0x80): Section mismatch: reference to .init.text:imx_set_mmc_info (between '__ksymtab_imx_set_mmc_info' and '__ksymtab_set_imx_fb_info') WARNING: arch/arm/mach-imx/built-in.o(__ksymtab+0x88): Section mismatch: reference to .init.text:set_imx_fb_info (after '__ksymtab_set_imx_fb_info') WARNING: arch/arm/mach-sa1100/built-in.o(.text+0x1930): Section mismatch: reference to .init.data:neponset_port_fns (between 'neponset_probe' and 'assabet_leds_event') WARNING: drivers/built-in.o(.text+0x3f100): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted') WARNING: drivers/built-in.o(.text+0x3f1c8): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted') WARNING: drivers/built-in.o(.text+0x4f988): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted') WARNING: drivers/built-in.o(.text+0x4fa50): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted') Signed-off-by: NSam Ravnborg <sam@ravnborg.org> Acked-by: NLennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 21 5月, 2007 1 次提交
-
-
由 Simon Arlott 提交于
Spelling fixes in arch/arm/. Signed-off-by: NSimon Arlott <simon@fire.lp0.eu> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 09 5月, 2007 1 次提交
-
-
由 Bernhard Walle 提交于
Add IRQF_IRQPOLL for each timer interrupt. Signed-off-by: NBernhard Walle <bwalle@suse.de> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 13 3月, 2007 2 次提交
-
-
由 Pavel Pisa 提交于
Only System PLL clock source is selectable by CSCR_SYSTEM_SEL bit. MPU PLL is driven by 512*CLK32 for each case. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Pavel Pisa 提交于
The minimal bus clock prescaler should be kept at value selected by the board / boot loader designer. Switching frequency above startup limit could lead to the external memory/devices misbehave. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 17 2月, 2007 1 次提交
-
-
由 Thomas Gleixner 提交于
Fixup the is_contionous replacement by a flag field. Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NIngo Molnar <mingo@elte.hu> Cc: Russell King <rmk@arm.linux.org.uk> Cc: john stultz <johnstul@us.ibm.com> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 24 1月, 2007 1 次提交
-
-
由 Pavel Pisa 提交于
The transition latency has to be defined and reasonably small to allow on-demand and conservative governors. The value has been defined according to manual. The imx_set_target() protected against seen out of range requests now. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 14 12月, 2006 1 次提交
-
-
由 Pavel Pisa 提交于
Support to change MX1 CPU frequency at runtime. Tested on PiKRON's PiMX1 board and seems to be fully stable up to 200 MHz end even as low as 8 MHz. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 08 12月, 2006 2 次提交
-
-
由 Pavel Pisa 提交于
Enhanced resolution for time measurement functions. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Pavel Pisa 提交于
The future high resolution support inclusion utilizes imx_decode_pll() in timer base frequency computation. This use requires more precise computation without discarding 10 bits by shifting left. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 30 11月, 2006 1 次提交
-
-
由 Russell King 提交于
set_irq_chipdata -> set_irq_chip_data get_irq_chipdata -> get_irq_chip_data do_level_IRQ -> handle_level_irq do_edge_IRQ -> handle_edge_irq do_simple_IRQ -> handle_simple_irq irqdesc -> irq_desc irqchip -> irq_chip Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 07 10月, 2006 1 次提交
-
-
由 Linus Torvalds 提交于
Untested, but this should fix up the bulk of the totally mechanical issues, and should make the actual detail fixing easier. Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 04 10月, 2006 1 次提交
-
-
由 Uwe Zeisberger 提交于
Many files include the filename at the beginning, serveral used a wrong one. Signed-off-by: NUwe Zeisberger <Uwe_Zeisberger@digi.com> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
- 02 8月, 2006 1 次提交
-
-
由 David Brownell 提交于
Patch from David Brownell ARM genirq cleanups/updates: - Start switching platforms to newer APIs * use "irq_chip" name, not "irqchip" * providing irq_chip.name - Show irq_chip.name in /proc/interrupts, like on x86. This update a bit more than half of the ARM code. The irq_chip.name values were chosen to match docs (if I have them) or be otherwise obvious ("FPGA", "CPLD", or matching the code). Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 03 7月, 2006 1 次提交
-
-
由 Thomas Gleixner 提交于
The irgflags consolidation did conflict with the ARM to generic IRQ conversion and was not applied for ARM. Fix it up. Use the new IRQF_ constants and remove the SA_INTERRUPT define Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 02 7月, 2006 1 次提交
-
-
由 Thomas Gleixner 提交于
Patch from Thomas Gleixner From: Thomas Gleixner <tglx@linutronix.de> Fixup the conversion to generic irq subsystem. Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 01 7月, 2006 1 次提交
-
-
由 Jörn Engel 提交于
Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
- 23 6月, 2006 1 次提交
-
-
由 Pavel Pisa 提交于
Patch from Pavel Pisa There has been bug, that dma_err_handler() touches even channels not signaling error condition. Problem noticed by Andrea Paterniani. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 09 6月, 2006 1 次提交
-
-
由 Matt Reimer 提交于
Patch from Matt Reimer There is a subtle bug in the GPIO interrupt status register handling in arch/arm/mach-imx/irq.c:imx_gpio_ack_irq(). The documentation states that a 1 should be written to the relevant bit to acknowledge a GPIO interrupt, but that is not what the code does. The problem is that the |= writes back 1s for all the *other* interrupts represented in the register, so interrupts could get lost. For example, if interrupts are pending for GPIO B10 and B12, ISR_B would have the value 0x00001400. Then when the interrupt code handles GPIO B10, it eventually calls imx_gpio_ack_irq(IRQ_GPIOB(10)), which effectively does this: ISR_B |= 1 << 10; with the result that (0x00001400 | 0x00000400) is written, clearing the interrupt status bits for *both* GPIO B10 and B12. The fix is to write 1s only for the interrupts we want to clear. The same problem seems to be occurring in the DMA code; this patch does not address those issues. Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NMatt Reimer <mreimer@vpop.net> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 08 5月, 2006 1 次提交
-
-
由 Sascha Hauer 提交于
Patch from Sascha Hauer This patch fixes the addruart macro to work with both mmu enabled and disabled. Signed-off-by: NSascha Hauer <s.hauer@pengutonix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 04 5月, 2006 1 次提交
-
-
由 Sascha Hauer 提交于
Patch from Sascha Hauer This patch moves the i.MX uart resources and the gpio pin setup to the board files. This allows the boards to decide how many internal uarts are connected to the outside world and whether they use rts/cts or not. Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 03 4月, 2006 1 次提交
-
-
由 Pavel Pisa 提交于
Patch from Pavel Pisa This patch adds support of i.MX/MX1 SD/MMC controller. It has been significantly redesigned from the original Sascha Hauer's version to support scatter-gather DMA, to conform to latest Pierre Ossman's and Russell King's MMC-SD Linux 2.6.x infrastructure. The handling of all events has been moved to the softirq context and is designed with no busy-looping in mind. Unfortunately some controller bugs has to be overcome by limited looping about 2-20 usec but these are observed only for initial card recognition phase. There are still some missing/missed IRQs problems under heavy load. Help of somebody with access to the full SDHC design information is probably necessary. Regenerated against 2.6.16-git-060402 to solve clash with other patches. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 02 4月, 2006 2 次提交
-
-
由 Pavel Pisa 提交于
Patch from Pavel Pisa From: Stefano Fedrigo <aleph@develer.com> This adds to the MX1ADS platform the needed code to detect insertion/removal of an MMC/SD card. Tested on a v1.1 board. Signed-off-by: NStefano Fedrigo <aleph@develer.com> Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Pavel Pisa 提交于
Patch from Pavel Pisa This patch contains simplified set of changes to add scatter-gather emulation capability into MX1 DMA support. The result should be still usable for next combination of DMA transfers Statter-Gather/linear/2D/FIFO to linear/2D/FIFO and linear/2D/FIFO to Statter-Gather/2D/FIFO The patch corrects channel priority allocation to be compatible with MX1 hardware implementation. Previous code has not been adapted from its PXA original. Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 05 2月, 2006 1 次提交
-
-
由 Russell King 提交于
imx.c does not use anything from serial.h, so remove it. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 14 1月, 2006 1 次提交
-
-
由 Nicolas Pitre 提交于
Patch from Nicolas Pitre This field is redundent since it must be equal to PHYS_OFFSET anyway. Now that no code uses it anymore, mark it deprecated and remove all initializations from the tree. Signed-off-by: NNicolas Pitre <nico@cam.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 06 1月, 2006 1 次提交
-
-
由 Sascha Hauer 提交于
Patch from Sascha Hauer - remove unnecessary mappings - rename mx1ads_device to cs89x0_device, because that's what it is - fix io/irq resource for cs89x0 device Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 31 10月, 2005 1 次提交
-
-
由 Tim Schmielau 提交于
I recently picked up my older work to remove unnecessary #includes of sched.h, starting from a patch by Dave Jones to not include sched.h from module.h. This reduces the number of indirect includes of sched.h by ~300. Another ~400 pointless direct includes can be removed after this disentangling (patch to follow later). However, quite a few indirect includes need to be fixed up for this. In order to feed the patches through -mm with as little disturbance as possible, I've split out the fixes I accumulated up to now (complete for i386 and x86_64, more archs to follow later) and post them before the real patch. This way this large part of the patch is kept simple with only adding #includes, and all hunks are independent of each other. So if any hunk rejects or gets in the way of other patches, just drop it. My scripts will pick it up again in the next round. Signed-off-by: NTim Schmielau <tim@physik3.uni-rostock.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 30 10月, 2005 1 次提交
-
-
由 Russell King 提交于
Convert everyone who uses platform_bus_type to include linux/platform_device.h. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk> Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
-