This patch removes the statically initialized tables from the i.MX serial
driver and makes the driver fully dependent on the information provided by
the platform_device.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

do not include board-mx31ads.h from hardware.h, instead include it
directly only where needed.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch annotates the platform_secondary_init function in
arch/arm/mach-realview/platsmp.c with trace_hardirqs_off to avoid a
warning when LOCKDEP and TRACE_IRQFLAGS are enabled.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Noticed by Martin Michlmayr, this missing export prevents IEEE1394
from building with:

ERROR: "dma_sync_sg_for_device" [drivers/ieee1394/ieee1394.ko] undefined!
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The list search success check in arch/arm/mach-pxa/ssp.c is wrong: for
example, it didn't recognise failure for me when I requested port 0.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Correcting the GPMC_PREFETCH_CONTROL register address
Signed-off-by: NThara Gopinath <thara@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Channel should be marked active only when DMA is really started. Otherwise
just omap_request_dma, omap_dma_link_lch and omap_dma_unlink_lch will cause
incorrect dump_stack().
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Work around:
arch/arm/mach-pxa/tosa.c: In function `tosa_poweroff':
arch/arm/mach-pxa/tosa.c:470: error: `GPIO_OUT' undeclared (first use in this function)
arch/arm/mach-pxa/tosa.c:470: error: (Each undeclared identifier is reported only once
arch/arm/mach-pxa/tosa.c:470: error: for each function it appears in.)

The proper fix exists in the PXA branch of my kernel git tree, which
will be pushed during the next merge window.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the IORESOURCE_IRQ_HIGHEDGE to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the IORESOURCE_IRQ_HIGHEDGE to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix resource_size_t warning in impd1.c, and printascii() build
errors in pci_v3.c
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This reverts commit 53491e04, which hit
the kernel tree too early.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Export the AT91 clock functions for the AT91X40. Some external code common
to all AT91 family parts relys on this, like the gpio and serial support.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

arch/arm/plat-omap/clock.c:397: warning: "struct cpufreq_frequency_table" declared inside parameter list
arch/arm/plat-omap/clock.c:397: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/plat-omap/clock.c: In function `clk_init_cpufreq_table':
arch/arm/plat-omap/clock.c:402: error: structure has no member named `clk_init_cpufreq_table'
arch/arm/plat-omap/clock.c:403: error: structure has no member named `clk_init_cpufreq_table'
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rename the SDI device if on an S3C2440 or S3C2442.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the IRQF_TRIGGER_ type to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the IRQF_TRIGGER_ type to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As noted by Russell King. These depend on tsc210x drivers
getting integrated first.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

collie.h:
     * add some meaningfull names to some gpios
collie.c:
    * initialize cpu registers correctly
Signed-off-by: NThomas Kunze <thommycheck@gmx.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

... so include the header file.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Two changes are necessary to enable proper operation of the DM9000 device with
the Colibri PXA 270 board: firstly, the IRQ type needs to be configured for
rising edge interrupts, and secondly this configuration needs to be
communicated through to the DM9000.

[akpm@linux-foundation.org: remove set_irq_type() call as per ben-linux request]
Signed-off-by: NMichael Abbott <michael.abbott@diamond.ac.uk>
Cc: Daniel Mack <daniel@caiaq.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds the missing MODULE_LICENSE("GPL").
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Whereas most Orion 5x machine support code would initialise the PCI
subsystem with nr_controllers in their struct hw_pci set to 2, the
DNS323 and Kurobox Pro machine support code had nr_controllers set
to 1.

This was presumably done because on those two machines, the PCI(-X)
controller (nr == 1) isn't used, requiring initialisation of only
the PCIe controller (nr == 0.)  However, not initialising the PCI(-X)
controller on boards that don't use it leads to a situation where
both the PCIe and the PCI(-X) controller think that their root bus is
zero, and it messes up IRQ assignment.

This patch changes the DNS323 and Kurobox Pro support code to always
use nr_controllers == 2.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The CPU's dma_flush_range() operation needs to clean+invalidate the
given memory area if the cache is in writeback mode, or do just the
invalidate part if the cache is in writethrough mode, but the current
proc-arm{925,926,940,946} (incorrectly) do a cache clean in the
latter case.  This patch fixes that.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Martin Michlmayr reported that fuse complains:
  ERROR: "copy_page" [fs/fuse/fuse.ko] undefined!

so export the needed function.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

irqs.h:
    * rename IRQ_LOCOMO_SPI_OVRN to IRQ_LOCOMO_SPI_REND
locomo.h:
    * add some definition for locomo spi controller
    * correct some errors
locomo.c:
    * correct some errors
    * add set_type for locomo gpio irq chip
Signed-off-by: NThomas Kunze <thommycheck@gmx.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Fix initialization of framebuffer not calling ioremap_writecombine() function
and not using internal SRAM for at91sam9rl.

This is a little rework of the "Don't initialize a pre-allocated framebuffer"
patch that corrects the call to ioremap_writecombine() function.

It also cuts the use of internal SRAM for at91sam9rl : it is a bit small
for a framebuffer.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A lot of stuff in spitz/akita/etc. depends on corgi_ssp to be initialised
early. However corgi_ssp initialisation fails, because at that time pxa*-ssp
devices don't have drivers. Move ssp earlier in the makefile so they are
registered before corgi-ssp.

Also move sleep/suspend and cpu-freq to more logical places
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fixed comments on global PRM register usage.
Signed-off-by: NKalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch removes following message on dpll5_m2_ck enable and
disable:

clock.c: Enable for dpll5_m2_ck without enable code
clock: clk_disable called on independent clock dpll5_m2_ck
which has no enable_reg
Signed-off-by: NJouni Hogander <jouni.hogander@nokia.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

ssi_l4_ick should have PARENT_CONTROLS_CLOCK flag.
ST_SSI_STDBY bit in idlest register cannot be used in  omap2_clk_wait_ready
Signed-off-by: NJouni Högander <jouni.hogander@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add fuctional clock enabler for iva2
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Wrong shift values were used for gpio2-6  fclks (gpt2-6 shift).
Signed-off-by: NJouni Högander <jouni.hogander@nokia.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Keymap fix for palmte and palmz71
Signed-off-by: NEduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Function enable_lnk does incorrect channel link on non-omap1 builds if chain
is created manually with omap_request_dma and omap_dma_link_lch functions.

Fix this by making sure that next_linked_ch field is initialized to -1 just
in omap_request_dma.
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Instead of BUG(), warn on disabling clocks with no users.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the omap2_set_globals_{242x,243x,343x}() functions. These
functions are called early upon boot in the map_io() functions in the
board-specific init files.

This patch was accidentally left out of the earlier series.

This fixes omap2 booting as noted by Kyungmin Park <kmpark@infradead.org>.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>