Implement reset as a separate function.
This will enable us to make sure that we don't do the
calculation again on every transfer.
Also at probe the reset is not added as the hwmod is doing that
for us.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

re-factor omap_i2c_init() so that we can re-use it for resume.
While at it also remove the bufstate variable as we write it
in omap_i2c_resize_fifo for every transfer.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The commit [i2c: omap: use revision check for OMAP_I2C_FLAG_APPLY_ERRATA_I207]
uses the revision id instead of the flag. So the flag can be safely removed.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The dtrev is used only for the comments. Remove the same and use
the scheme instead to know if it is version2.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The errata i207 is enabled for 2430 and 3xxx. Use the revision check
to enable the erratum instead.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The revision register on OMAP4 is a 16-bit lo and a 16-bit
hi. Currently the driver reads only the lower 8-bits.
Fix the same by preventing the truncating of the rev register
for OMAP4.

Also use the scheme bit ie bit-14 of the hi register to know if it
is OMAP_I2C_IP_VERSION_2.

On platforms previous to OMAP4 the offset 0x04 is IE register whose
bit-14 reset value is 0, the code uses the same to its advantage.

Also since the omap_i2c_read_reg uses reg_map_ip_* a raw_readw is done
to fetch the revision register.

The dev->regs is populated after reading the rev_hi. A NULL check
has been added in the resume handler to prevent the access before
the setting of the regs.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Some GPIO expanders need some early pin control muxing. Due to
legacy boards sometimes the driver uses subsys_initcall instead of
module_init. This patch takes advantage of defer probe feature
and pin control in order to wait until pin control probing before
GPIO driver probing. It has been tested on OMAP5 board with TCA6424
driver.
Signed-off-by: NSebastien Guiriec <s-guiriec@ti.com>
Acked-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

if we allow compiler reorder our writes, we could
fall into a situation where dev->buf_len is reset
for no apparent reason.

This bug was found with a simple script which would
transfer data to an i2c client from 1 to 1024 bytes
(a simple for loop), when we got to transfer sizes
bigger than the fifo size, dev->buf_len was reset
to zero before we had an oportunity to handle XDR
Interrupt. Because dev->buf_len was zero, we entered
omap_i2c_transmit_data() to transfer zero bytes,
which would mean we would just silently exit
omap_i2c_transmit_data() without actually writing
anything to DATA register. That would cause XDR
IRQ to trigger forever and we would never transfer
the remaining bytes.

After adding the memory barrier, we also drop resetting
dev->buf_len to zero in omap_i2c_xfer_msg() because
both omap_i2c_transmit_data() and omap_i2c_receive_data()
will act until dev->buf_len reaches zero, rendering the
other write in omap_i2c_xfer_msg() redundant.

This patch has been tested with pandaboard for a few
iterations of the script mentioned above.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

This reverts commit 3db11fef
(ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints).
This commit causes I2C timeouts to appear on several OMAP3430/3530-based
boards:

  http://marc.info/?l=linux-arm-kernel&m=135071372426971&w=2
  http://marc.info/?l=linux-arm-kernel&m=135067558415214&w=2
  http://marc.info/?l=linux-arm-kernel&m=135216013608196&w=2

and appears to have been sent for merging before one of its prerequisites
was merged:

  http://marc.info/?l=linux-arm-kernel&m=135219411617621&w=2Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NJean Pihet <j-pihet@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The driver claims to support SMBus quick command but it was not the
case. This patch fixes this issue. Without it, i2cdetect finds imaginary
devices. And with some IP versions, trying to send 0 byte can cause
issue when writing data to an EEPROM.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

[wsa: improved the commit message]
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

When having multiple i2c-gpio nodes, the name for each is same.
So add the patch to fix it.

The adap->name printing information was added by myself

without this patch the log information is as following
---<8---
adap->name = i2c-gpio-1
i2c-gpio i2c.2: using pins 30 (SDA) and 31 (SCL)
adap->name = i2c-gpio-1
i2c-gpio i2c.3: using pins 64 (SDA) and 65 (SCL)
--->8---

with this patch, the log information is as following
---<8---
adap->name = i2c.2
i2c-gpio i2c.2: using pins 30 (SDA) and 31 (SCL)
adap->name = i2c.3
i2c-gpio i2c.3: using pins 64 (SDA) and 65 (SCL)
--->8---
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>

[wsa: minor fixes to the commit mesage]
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Replacing the devm_request_mem_region() and devm_ioremap_nocache() calls
by a single call to devm_request_and_ioremap() simplifies the code.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Give the driver struct a name according to the 'standard' to fix:

WARNING: vmlinux.o(.data+0x11798): Section mismatch in reference from the variable rcar_i2c_drv to the function .devinit.text:rcar_i2c_probe()
...
WARNING: vmlinux.o(.data+0x1179c): Section mismatch in reference from the variable rcar_i2c_drv to the function .devexit.text:rcar_i2c_remove()
Reported-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.

So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: Nliu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

When watching the irqs name of tegra i2c, all instances
irq name shows as tegra_i2c.

Passing the device name properly to have the irq names with
instance like tegra-i2c.0, tegra-i2c.1 etc.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Make sure to clk_prepare as well as clk_enable.
Signed-off-by: NPhilippe Begnic <philippe.begnic@stericsson.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

This I2C master can do DMA and PIOQUEUE (PIO with FIFO). Originally,
only PIOQUEUE was supported and it had issues, then DMA support was added
this cycle. The original intention was to keep PIOQUEUE since it has
less overhead what is nice for small transfers. However, runtime
switching between PIOQEUE and DMA depending on the transfer size never
worked despite a lot of trying. Since PIOQUEUE mode itself was flaky
(polling at places where interrupts failed to work) and the
implementation also imposed a size limit for transfers, it is best to
remove the support, so users don't fall over its limitations. It also
makes the driver a lot cleaner and more robust. If somebody really wants
less overhead, plain PIO mode could still be implemented with the
addidtional advantage that this mode is also available on MX23, too.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Reviewed-by: NMarek Vasut <marex@denx.de>

Signed-off-by: NJean Delvare <khali@linux-fr.org>

Arbitrarily selecting GPIOLIB causes trouble on some architectures,
so don't do that. Instead, just make the optional multiplexing code
depend on CONFIG_I2C_MUX_GPIO instead of CONFIG_I2C_MUX for now. We
can revisit if the i2c-i801 driver ever supports other multiplexing
flavors.

Also make that optional code depend on DMI, as it won't do anything
without that.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>

Move the i2c-stub driver to drivers/i2c, to match the Kconfig entry.
This is less confusing that way.

I also fixed all checkpatch warnings and errors.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Peter Huewe <peterhuewe@gmx.de>

This patch implements DMA support into mxs-i2c. DMA transfers are now enabled
via DT. The DMA operation is enabled by default.
Signed-off-by: NMarek Vasut <marex@denx.de>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>

[wsa: rebased to 3.6-rc7]
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

R-Car I2C is similar with SH7760 I2C.
But the SH7760 I2C driver had many workaround operations, since H/W had bugs.
Thus, it was pointless to keep compatible between SH7760 and R-Car I2C drivers.
This patch creates new Renesas R-Car I2C driver.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Convert the driver from the outdated omap_pm_set_max_mpu_wakeup_lat
API to the new PM QoS API.
Since the constraint is on the MPU subsystem, use the PM_QOS_CPU_DMA_LATENCY
class of PM QoS. The resulting MPU constraints are used by cpuidle to
decide the next power state of the MPU subsystem.

The I2C device latency timing is derived from the FIFO size and the
clock speed and so is applicable to all OMAP SoCs.
Signed-off-by: NJean Pihet <j-pihet@ti.com>
Acked-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Here we apply the bindings required for successful Device Tree
probing of the i2c-nomadik driver.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Fix build failure in Intel PIIX4 I2C driver.
Signed-off-by: NDaniel J Blueman <daniel@quora.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org [v3.6]

Now that i2c-mux-gpio is able to find the GPIO chip by itself, we can
delegate this task. The great thing here is that i2c-mux-gpio can
defer device probing until the gpio chip is available, so we no longer
depend on the module loading order.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support for SMBus multiplexing on Asus Z8 motherboard series. On
these boards, the memory slots are behind a GPIO-controlled I2C
multiplexer. Models with 6 or 12 memory slots have 2 segments behind
the multiplexer, while models with 18 memory slots have 3 such
segments.

On these boards, only the memory slots are behind the multiplexer,
so it is possible to keep the autodetection mechanism.

The code is generic enough so it could work on other boards as long as
the multiplexer is controlled by GPIO pins. For other forms of
multiplexing (for example using an I2C device) additional code will be
needed.

Thanks to Asus for providing a board to develop and test this feature,
as well as all the technical information required.

At the moment, the GPIO driver must be loaded before the i2c-i801
driver, but I hope to solve this soon, using deferred probing on
the i2c-mux-gpio side.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The SMBus controller in the VIA VX900 appears to be compatible with
the VIA VX855, so just add the device ID.

This closes kernel bug #43096.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

i2c_parport_irq is only called internally so it can be static.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

i2c_dw_xfer_msg is only called internally so it can be static. It
original was, before the driver split. No idea why it was changed at
that time.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NDirk Brandewie <dirk.brandewie@gmail.com>

Replace printks with pr_<level>s, add pr_fmt()s to replace NAMEs
Signed-off-by: NJim Cromie <jim.cromie@gmail.com>
Reviewed-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Remove the global dependency of the I2C subsystem on HAS_IOMEM and
move the dependency to the i2c/busses submenu, with an exception for
i2c-stub.

The generic I2C part does not need to have HAS_IOMEM set and thus now
becomes available in UML, so the I2C subsystem can now be used, e.g.
by the i2c-stub driver, for development of I2C device drivers.

[JD: Some adjustments.]

[Heiko Carstens: Keep I2C disabled on S390.]
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the samsung include directories
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: linux-samsung-soc@vger.kernel.org

mpc_i2c_stop() only initiates STOP but does not wait for it to
hit the I2C bus. This is a problem when using I2C devices which
uses fairly long clock stretching just before STOP if you also
have an i2c-mux which may switch to another bus before STOP has
been processed.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

As a first step towards migrating davinci platforms to use common clock
framework, replace all instances of clk_enable() with clk_prepare_enable()
and clk_disable() with clk_disable_unprepare(). Until the platform is
switched to use the CONFIG_HAVE_CLK_PREPARE Kconfig variable, this just
adds a might_sleep() call and would work without any issues.

This will make it easy later to switch to common clk based implementation
of clk driver from DaVinci specific driver.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the w90x900 include directories
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the imx include directories
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NSascha Hauer <kernel@pengutronix.de>
Acked-by: NVinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>