Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 14
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 09 11月, 2017 1 次提交
  3. 07 11月, 2017 3 次提交
  5. 03 11月, 2017 1 次提交
  7. 21 9月, 2017 1 次提交
  9. 12 4月, 2017 1 次提交
  11. 19 1月, 2017 1 次提交
    • J
      usb: core: update comments for send message functions · 123b7b30
      由 Jaejoong Kim 提交于 
      The commonly use of bottom halves are tasklet and workqueue. The big
difference between tasklet and workqueue is that the tasklet runs in
an interrupt context and the workqueue runs in a process context,
which means it can sleep if need be.

The comment for usb_control/interrupt/bulk_msg() functions note that do
not use this function within an interrupt context, like a 'bottom half'
handler. With this comment, it makes confuse about usage of these
functions.

To more clarify, remove 'bottom half' comment.
Signed-off-by: NJaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      123b7b30
  13. 30 10月, 2016 1 次提交
  15. 13 9月, 2016 1 次提交
    • R
      usb: core: setup dma_pfn_offset for USB devices and, interfaces · b44bbc46
      由 Roger Quadros 提交于 
      If dma_pfn_offset is not inherited correctly from the host controller,
it might result in sub-optimal configuration as bounce
buffer limit might be set to less than optimal level.

Consider the mass storage device case.
USB storage driver creates a scsi host for the mass storage interface in
drivers/usb/storage/usb.c
The scsi host parent device is nothing but the the USB interface device.
Now, __scsi_init_queue() calls scsi_calculate_bounce_limit() to find out
and set the block layer bounce limit.
scsi_calculate_bounce_limit() uses dma_max_pfn(host_dev) to get the
bounce_limit. host_dev is nothing but the device representing the
mass storage interface.
If that device doesn't have the right dma_pfn_offset, then dma_max_pfn()
is messed up and the bounce buffer limit is wrong.

e.g. On Keystone 2 systems, dma_max_pfn() is 0x87FFFF and dma_mask_pfn
is 0xFFFFF. Consider a mass storage use case: Without this patch,
usb scsi host device (usb-storage) will get a dma_pfn_offset of 0 resulting
in a dma_max_pfn() of 0xFFFFF within the scsi layer
(scsi_calculate_bounce_limit()).
This will result in bounce buffers being unnecessarily used.

Hint: On 32-bit ARM platforms dma_max_pfn() = dma_mask_pfn + dma_pfn_offset
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      b44bbc46
  17. 31 8月, 2016 1 次提交
  19. 18 7月, 2016 1 次提交
  21. 27 4月, 2016 2 次提交
  23. 04 10月, 2015 1 次提交
  25. 23 9月, 2015 2 次提交
  27. 19 8月, 2015 2 次提交
  29. 15 8月, 2015 2 次提交
  31. 25 1月, 2015 1 次提交
    • A
      USB: don't cancel queued resets when unbinding drivers · 524134d4
      由 Alan Stern 提交于 
      The USB stack provides a mechanism for drivers to request an
asynchronous device reset (usb_queue_reset_device()).  The mechanism
uses a work item (reset_ws) embedded in the usb_interface structure
used by the driver, and the reset is carried out by a work queue
routine.

The asynchronous reset can race with driver unbinding.  When this
happens, we try to cancel the queued reset before unbinding the
driver, on the theory that the driver won't care about any resets once
it is unbound.

However, thanks to the fact that lockdep now tracks work queue
accesses, this can provoke a lockdep warning in situations where the
device reset causes another interface's driver to be unbound; see

	http://marc.info/?l=linux-usb&m=141893165203776&w=2

for an example.  The reason is that the work routine for reset_ws in
one interface calls cancel_queued_work() for the reset_ws in another
interface.  Lockdep thinks this might lead to a work routine trying to
cancel itself.  The simplest solution is not to cancel queued resets
when unbinding drivers.

This means we now need to acquire a reference to the usb_interface
when queuing a reset_ws work item and to drop the reference when the
work routine finishes.  We also need to make sure that the
usb_interface structure doesn't outlive its parent usb_device; this
means acquiring and dropping a reference when the interface is created
and destroyed.

In addition, cancelling a queued reset can fail (if the device is in
the middle of an earlier reset), and this can cause usb_reset_device()
to try to rebind an interface that has been deallocated (see
http://marc.info/?l=linux-usb&m=142175717016628&w=2 for details).
Acquiring the extra references prevents this failure.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NRussell King - ARM Linux <linux@arm.linux.org.uk>
Reported-by: NOlivier Sobrie <olivier@sobrie.be>
Tested-by: NOlivier Sobrie <olivier@sobrie.be>
Cc: stable <stable@vger.kernel.org> # 3.19
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      524134d4
  33. 29 9月, 2014 1 次提交
  35. 05 3月, 2014 1 次提交
  37. 19 2月, 2014 1 次提交
  39. 08 2月, 2014 1 次提交
    • V
      staging: usbip: convert usbip-host driver to usb_device_driver · b7945b77
      由 Valentina Manea 提交于 
      This driver was previously an interface driver. Since USB/IP
exports a whole device, not just an interface, it would make
sense to be a device driver.

This patch also modifies the way userspace sees and uses a
shared device:

* the usbip_status file is no longer created for interface 0, but for
the whole device (such as
/sys/devices/pci0000:00/0000:00:01.2/usb1/1-1/usbip_status).
* per interface information, such as interface class or protocol, is
no longer sent/received; only device specific information is
transmitted.
* since the driver was moved one level below in the USB architecture,
there is no need to bind/unbind each interface, just the device as a
whole.
Signed-off-by: NValentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      b7945b77
  41. 09 1月, 2014 1 次提交
  43. 08 1月, 2014 1 次提交
  45. 17 10月, 2013 1 次提交
    • S
      usb: Push USB2 LPM disable on disconnect into USB core. · f468f7b9
      由 Sarah Sharp 提交于 
      The USB core currently handles enabling and disabling optional USB power
management features during device transitions (device suspend/resume,
driver bind/unbind, device reset, and device disconnect).  Those
optional power features include Latency Tolerance Messaging (LTM),
USB 3.0 Link PM, and USB 2.0 Link PM.

The USB core currently enables LPM on device enumeration and disables
USB 2.0 Link PM when the device is reset.  However, the xHCI driver
disables LPM when the device is disconnected and the device context is
freed.  Push the call up into the USB core, in order to be consistent
with the core handling all power management enabling and disabling.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      f468f7b9
  47. 03 8月, 2013 1 次提交
  49. 01 8月, 2013 1 次提交
  51. 18 5月, 2013 2 次提交
  53. 12 1月, 2013 1 次提交
  55. 22 11月, 2012 2 次提交
  57. 12 11月, 2012 1 次提交
    • A
      USB: fix endpoint-disabling for failed config changes · 36caff5d
      由 Alan Stern 提交于 
      This patch (as1631) fixes a bug that shows up when a config change
fails for a device under an xHCI controller.  The controller needs to
be told to disable the endpoints that have been enabled for the new
config.  The existing code does this, but before storing the
information about which endpoints were enabled!  As a result, any
second attempt to install the new config is doomed to fail because
xhci-hcd will refuse to enable an endpoint that is already enabled.

The patch optimistically initializes the new endpoints' device
structures before asking the device to switch to the new config.  If
the request fails then the endpoint information is already stored, so
we can use usb_hcd_alloc_bandwidth() to disable the endpoints with no
trouble.  The rest of the error path is slightly more complex now; we
have to disable the new interfaces and call put_device() rather than
simply deallocating them.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NMatthias Schniedermeyer <ms@citd.de>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      36caff5d
  59. 14 9月, 2012 1 次提交
  61. 11 7月, 2012 2 次提交
    • S
      USB: Enable Latency Tolerance Messaging (LTM). · f74631e3
      由 Sarah Sharp 提交于 
      USB 3.0 devices may optionally support a new feature called Latency
Tolerance Messaging.  If both the xHCI host controller and the device
support LTM, it should be turned on in order to give the system hardware
a better clue about the latency tolerance values of its PCI devices.

Once a Set Feature request to enable LTM is received, the USB 3.0 device
will begin to send LTM updates as its buffers fill or empty, and it can
tolerate more or less latency.

The USB 3.0 spec, section C.4.2 says that LTM should be disabled just
before the device is placed into suspend.  Then the device will send an
updated LTM notification, so that the system doesn't think it should
remain in an active state in order to satisfy the latency requirements
of the suspended device.

The Set and Clear Feature LTM enable command can only be sent to a
configured device.  The device will respond with an error if that
command is sent while it is in the Default or Addressed state.  Make
sure to check udev->actconfig in usb_enable_ltm() and usb_disable_ltm(),
and don't send those commands when the device is unconfigured.

LTM should be enabled once a new configuration is installed in
usb_set_configuration().  If we end up sending duplicate Set Feature LTM
Enable commands on a switch from one installed configuration to another
configuration, that should be harmless.

Make sure that LTM is disabled before the device is unconfigured in
usb_disable_device().  If no drivers are bound to the device, it doesn't
make sense to allow the device to control the latency tolerance of the
xHCI host controller.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      f74631e3
    • S
      USB: Fix LPM disable count mismatch on driver unbind. · 24971912
      由 Sarah Sharp 提交于 
      When a user runs `echo 0 > bConfigurationValue` for a USB 3.0 device,
usb_disable_device() is called.  This function disables all drivers,
deallocates interfaces, and sets the device configuration value to 0
(unconfigured).

With the new scheme to ensure that unconfigured devices have LPM
disabled, usb_disable_device() must call usb_unlocked_disable_lpm() once
it unconfigures the device.

This commit should be backported to kernels as old as 3.5, that contain
the commit 8306095f "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
      24971912