- 25 2月, 2012 1 次提交
-
-
由 Tony Lindgren 提交于
There's no need to have these in plat/io.h. While at it, clean up the includes to group them like they typically are grouped. Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 23 2月, 2012 2 次提交
-
-
由 Tomi Valkeinen 提交于
Some OMAP1 board files define LCD platform_devices, but there are no corresponding LCD drivers for those in the kernel. Thus remove these LCD devices. Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: NTony Lindgren <tony@atomide.com>
-
由 Tomi Valkeinen 提交于
LCD config for old omapfb driver is passed with OMAP_TAG_LCD from board files or from the bootloader. In an effort to remove OMAP_TAG_LCD, this patch adds omapfb_set_lcd_config() function that the board files can call to set the LCD config. This has the drawback that configuration can no longer come from the bootloader. Of the boards supported by the kernel, this should only affect N770 which depends on the data from the bootloader. This patch adds an LCD config for N770 to its board files, but that is most probably broken. Fixing this would need information about the HW setup in N770 boards. Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: NTony Lindgren <tony@atomide.com>
-
- 05 1月, 2012 1 次提交
-
-
由 Russell King 提交于
Hook these platforms restart code into the new restart hook rather than using arch_reset(). Acked-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 18 11月, 2011 1 次提交
-
-
由 Tony Lindgren 提交于
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>, there's no need to keep local prototypes in non-local headers. Add mach-omap1/common.h and mach-omap2/common.h and move the local prototypes there from plat/common.h and mach/omap4-common.h. Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 01 11月, 2011 1 次提交
-
-
由 Paul Gortmaker 提交于
These files all make use of one of the EXPORT_SYMBOL variants or the THIS_MODULE macro. So they will need <linux/export.h> Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
-
- 20 10月, 2011 1 次提交
-
-
由 Tony Lindgren 提交于
This allows removing omap hacks for map_io allowing generic map_io. Note that in the future we can't do cpu_is_omapxxxx detection until in init_early. This means that board-innovator.c now assumes 15xx only, and board-generic.c assumes 16xx only. This is best fixed later on by passing the SoC type from device tree. Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 22 8月, 2011 1 次提交
-
-
由 Nicolas Pitre 提交于
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org> Acked-by: NTony Lindgren <tony@atomide.com> Acked-by: NArnd Bergmann <arnd@arndb.de>
-
- 08 8月, 2011 1 次提交
-
-
由 Russell King 提交于
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h before we start consolidating the individual platform implementations of the gpio header files. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 20 6月, 2011 1 次提交
-
-
由 Tony Lindgren 提交于
This is needed for the following patches so we can initialize the rest of the hardware timers later on. As with the init_irq calls, there's no need to do cpu_is_omap calls during the timer init as we only care about the major omap generation. This means that we can initialize the sys_timer with the .timer entries alone. Note that for now we just set stubs for the various sys_timer entries that will get populated in a later patch. The following patches will also remove the omap_dm_timer_init calls and change the init for the rest of the hardware timers to happen with an arch_initcall. Signed-off-by: NTony Lindgren <tony@atomide.com> Reviewed-by: NKevin Hilman <khilman@ti.com>
-
- 16 6月, 2011 1 次提交
-
-
由 Tony Lindgren 提交于
This allows us to remove cpu_is_omap calls from init_irq functions. There should not be any need for cpu_is_omap calls as at this point. During the timer init we only care about SoC generation, and not about subrevisions. The main reason for the patch is that we want to initialize only minimal omap specific code from the init_early call. Signed-off-by: NTony Lindgren <tony@atomide.com> Reviewed-by: NKevin Hilman <khilman@ti.com>
-
- 31 3月, 2011 1 次提交
-
-
由 Lucas De Marchi 提交于
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>
-
- 23 12月, 2010 1 次提交
-
-
由 Janusz Krzysztofik 提交于
Most keypad drivers make use of the <linux/input/matrix_keypad.h> defined macros, structures and inline functions. Convert omap-keypad driver to use those as well, as suggested by a compile time warning, hardcoded into the OMAP <palt/keypad.h>. Created against linux-2.6.37-rc5. Tested on Amstrad Delta. Compile tested with omap1_defconfig and omap2plus_defconfig shrinked to board-h4. Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl> Reviewed-by: NAaro Koskinen <aaro.koskinen@nokia.com> Acked-by: NDmitry Torokhov <dtor@mail.ru> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 08 12月, 2010 1 次提交
-
-
由 Varadarajan, Charulatha 提交于
Implement GPIO as a platform device. GPIO APIs are used in machine_init functions. Hence it is required to complete GPIO probe before board_init. Therefore GPIO device register and driver register are implemented as postcore_initcalls. omap_gpio_init() does nothing now and this function would be removed in the next patch as it's usage is spread across most of the board files. Inorder to convert GPIO as platform device, modifications are required in clockxxxx_data.c file for OMAP1 so that device names can be used to obtain clock instead of getting clocks by name/NULL ptr. Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling or disabling the clocks, modify sysconfig settings and remove usage of clock FW APIs. Note 1: Converting GPIO driver to use runtime PM APIs is not done as a separate patch because GPIO clock names are different for various OMAPs and are different for some of the banks in the same CPU. This would need usage of cpu_is checks and bank id checks while using clock FW APIs in the gpio driver. Hence while making GPIO a platform driver framework, PM runtime APIs are used directly. Note 2: While implementing GPIO as a platform device, pm runtime APIs are used as mentioned above and modification is not done in gpio's prepare for idle/ resume after idle functions. This would be done in the next patch series and GPIO driver would be made to use dev_pm_ops instead of sysdev_class in that series only. Due to the above, the GPIO driver implicitly relies on CM_AUTOIDLE = 1 on its iclk for power management to work, since the driver never disables its iclk. This would be taken care in the next patch series (see Note 3 below). Refer to http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html for more details. Note 3: only pm_runtime_get_sync is called in gpio's probe() and pm_runtime_put* is never called. This is to make the implementation similar to the existing GPIO code. Another patch series would be sent to correct this. In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They are enabled/ disabled whenever required using clock framework APIs TODO: 1. Cleanup the GPIO driver. Use function pointers and register offest pointers instead of using hardcoded values 2. Remove all cpu_is_ checks and OMAP specific macros 3. Remove usage of gpio_bank array so that only instance specific information is used in driver code 4. Rename 'method'/ avoid it's usage 5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4 6. Modify gpio's prepare for idle/ resume after idle functions to use runtime pm implentation. Signed-off-by: NCharulatha V <charu@ti.com> Signed-off-by: NRajendra Nayak <rnayak@ti.com> Reviewed-by: NBasak, Partha <p-basak2@ti.com> Acked-by: NKevin Hilman <khilman@deeprootsystems.com> [tony@atomide.com: updated for bank specific revision and updated boards] Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 20 10月, 2010 1 次提交
-
-
由 Nicolas Pitre 提交于
Since we're now using addruart to establish the debug mapping, we can remove the io_pg_offst and phys_io members of struct machine_desc. The various declarations were removed using the following script: grep -rl MACHINE_START arch/arm | xargs \ sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }' [ Initial patch was from Jeremy Kerr, example script from Russell King ] Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org> Acked-by: Eric Miao <eric.miao at canonical.com>
-
- 16 7月, 2010 1 次提交
-
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 05 7月, 2010 1 次提交
-
-
由 Tony Lindgren 提交于
Move omap1 FS USB platform init code into mach-omap1/usb.c Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 16 2月, 2010 1 次提交
-
-
由 Ladislav Michl 提交于
Convert OMAP based boards to use physmap-flash. Refreshed against today's Linux omap kernel tree Cc: linux-mtd@lists.infradead.org Signed-off-by: NLadislav Michl <ladis@linux-mips.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 23 10月, 2009 1 次提交
-
-
由 Janusz Krzysztofik 提交于
Commit 15ac408e removed enabled_uart and OMAP_TAG_UART. This works for mach-omap2, but causes issues on mach-omap1 for some boards as the mach-omap1 serial.c was muxing pins based on the enabled_uart flag for 15xx. Fix this by muxing pins in board-*.c files for the 15xx boards for the uart ports that had enabled_uart flag set before the commit above. Tested on Amsdtrad Delta only. Note that in the future we should add support for powering down the uarts with a timer like mach-omap2/serial.c does. Otherwise the enabled uarts will be blocking retention-while-idle. Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 21 10月, 2009 1 次提交
-
-
由 Tony Lindgren 提交于
Move the remaining headers under plat-omap/include/mach to plat-omap/include/plat. Also search and replace the files using these headers to include using the right path. This was done with: #!/bin/bash mach_dir_old="arch/arm/plat-omap/include/mach" plat_dir_new="arch/arm/plat-omap/include/plat" headers=$(cd $mach_dir_old && ls *.h) omap_dirs="arch/arm/*omap*/ \ drivers/video/omap \ sound/soc/omap" other_files="drivers/leds/leds-ams-delta.c \ drivers/mfd/menelaus.c \ drivers/mfd/twl4030-core.c \ drivers/mtd/nand/ams-delta.c" for header in $headers; do old="#include <mach\/$header" new="#include <plat\/$header" for dir in $omap_dirs; do find $dir -type f -name \*.[chS] | \ xargs sed -i "s/$old/$new/" done find drivers/ -type f -name \*omap*.[chS] | \ xargs sed -i "s/$old/$new/" for file in $other_files; do sed -i "s/$old/$new/" $file done done for header in $(ls $mach_dir_old/*.h); do git mv $header $plat_dir_new/ done Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 29 8月, 2009 1 次提交
-
-
由 Kalle Valo 提交于
OMAP tags are deprecrated so drop them. Drop UART config data which decides which UARTs to enable during boot. This is no longer necessary since serial core code disables clocks after inactivity. Background: with new UART idle code, all on-chip UARTs are idled using a configurable inactivity timer (default 5 seconds.) After the inactivity timer, UART clocks are disabled automatically. Signed-off-by: NKalle Valo <kalle.valo@iki.fi> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 24 3月, 2009 2 次提交
-
-
由 Felipe Balbi 提交于
OMAP_TAGS should vanish soon since they're not generic arm tags. Most of them can be converted to a platform_data or parsed from a command line like e.g. serial tag. For OMAP_TAG_USB we just let boards call omap_usb_init() passing a pointer to omap_usb_config. Patch updated by Tony for mainline, basically make n770 and h4 compile. Also folded in a fix for OSK by David Brownell <dbrownell@users.sourceforge.net>. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Tony Lindgren 提交于
Move the defines to the associated board file and remove the now unnecessary header files. Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 15 1月, 2009 2 次提交
-
-
由 Tony Lindgren 提交于
This patch removes old platform devices. Alsa should now be using the ASoC driver. For boards not yet using ASoC, please see sound/soc/omap/osk5912.c. Add dummy aic23_power_up and aic23_power_down functions for 770 to keep things compiling. Remove references to omap_gpio_switch, and unused h2_nand_dev_ready function. This patch is based on an earlier patch by Arun KS. Cc: Jarkko Nikula <jarkko.nikula@nokia.com> Signed-off-by: NArun KS <arunks@mistralsolutions.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Jarkko Nikula 提交于
Fix compile by removing remaining omap specific gpio calls. Based on earlier patches by Jarkko Nikula. Also remove old GPIO key code, there is already a patch to do this with gpio_keys. Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 11 12月, 2008 3 次提交
-
-
由 Tony Lindgren 提交于
Most of the omap1 MMC boards got broken by an earlier patch 138ab9f8. If you look closely, the MMC init funtions are pretty much just stubs. Remove broken init code to make room for cleaner MMC init code. Cc: Pierre Ossman <drzeus-mmc@drzeus.cx> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 David Brownell 提交于
More conversion to the standard GPIO interfaces: stop using omap_set_gpio_direction() entirely, and switch over to the gpio_direction_output() call. Note that because gpio_direction_output() includes the initial value, this change isn't quite transparent. - For the call sites which defined an initial value either before or after setting the direction, that value was used. When that value was previously assigned afterwards, this could eliminate a brief output glitch ... and possibly change behavior. In a few cases (LCDs) several values were assigned together ... those were re-arranged to match the explicit sequence provided. - Some call sites didn't define such a value; so I chose an initial "off/reset" value that seemed to default to "off". In short, files touched by this patch might notice some small changes in startup behavior (with trivial fixes). Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 David Brownell 提交于
This patch replaces some legacy OMAP GPIO calls with the "new" (not really, any more!) calls that work on most platforms. The calls addressed by this patch are the simple ones to get and set values ... for code that's in mainline, including the implementations of those calls. Except for the declarations and definitions of those calls, all of these changes were performed by a simple SED script. Plus, a few "if() set() else set()" branches were merged by hand. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 07 8月, 2008 2 次提交
-
-
由 Russell King 提交于
This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h. Then, since asm/hardware.h only exists to include asm/arch/hardware.h, update everything to directly include asm/arch/hardware.h and remove asm/hardware.h. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 25 2月, 2008 1 次提交
-
-
由 Jean Delvare 提交于
Each call to i2c_get_adapter() must be followed by a call to i2c_put_adapter() to release the grabbed reference. Otherwise the reference count grows forever and the adapter can never be unregistered. Signed-off-by: NJean Delvare <khali@linux-fr.org> Acked-by: NVladimir Ananiev <vovan888@gmail.com> Acked-by: NTony Lindgren <tony@atomide.com>
-
- 09 2月, 2008 3 次提交
-
-
由 Tony Lindgren 提交于
This patch cleans up omap1 files to sync up with linux-omap tree: - Remove omap-generic MMC config as it should be defined in board-*.c files instead of using board-generic.c - New style I2C board_info from David Brownell <dbrownell@users.sourceforge.net> - Init section fixes from Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Jarkko Nikula 提交于
This patch starts using introduced I2C bus registration helper by cleaning up registration currently done in various places and by doing necessary board file modifications. Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com> Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Carlos Eduardo Aguiar 提交于
Use MMC multislot structures for Siemens SX1 board Signed-off-by: NCarlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 21 9月, 2007 1 次提交
-
-
由 Vladimir Ananiev 提交于
This adds basic support for Siemens SX1. More patches are available, with video driver, mixer, and serial ports working. That is enough to do gsm calls with right userland. Signed-off-by: NPavel Machek <pavel@suse.cz> Signed-off-by: NTony Lindgren <tony@atomide.com>
-