Use devm_*() functions to make cleanup paths simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NJean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds the support of the I2C_SMBUS_I2C_BLOCK_DATA transaction
type for the iSMT SMBus Controller.
Signed-off-by: NRobert Valiquette <robert.valiquette@intel.com>
Acked-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

OSIF, Open Source InterFace, is a USB based i2c bus master.  The
origional design was based on i2c-tiny-usb, but more modern versions
of the firmware running on the MegaAVR microcontroller use a different
protocol over the USB. This code is based on Barry Carter
<barry.carter@gmail.com> driver.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The RobotFuzz device is not compatible with i2c-tiny-usb. Remove its
entry from the USB table so that the new correct driver can be used.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h
like this platform driver need not depend on HAVE_CLK. Also, remove a
redundant clk.h include from core driver.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The Nomadik I2C is now configured from the device tree on all platforms
using this controller. Delete the platform data header and move the
definitions into the driver so it is all contained in one single file.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The Nomadik I2C controller needs to have the slave set-up time
configured based off the clock used to drive the I2C bus block.
Currently this is done with static assignments assuming that the
block is clocked 48MHz which is pretty likely to be bug-prone.
Calculate the SLSU from the equation given in the datasheet
instead.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

cppcheck rightfully says:

drivers/i2c/busses/i2c-viperboard.c:169: style: Variable 'bytes_xfer' is assigned a value that is never used.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NLars Poeschel <poeschel@lemonage.de>

Simplified the probe and remove functions using devm_* functions
Signed-off-by: NKedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

IRQ handler has to be register first before IRQ
is enabled in xiic_reinit().
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Code changes to fix checkpatch warnings listed below.
- WARNING: please, no space before tabs
- WARNING: quoted string split across lines
Signed-off-by: NKedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Use devm_request_region() to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Use devm_kzalloc() functions to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NLars Poeschel <poeschel@lemonage.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

smatch rightfully says:
drivers/i2c/busses/i2c-imx.c:610 i2c_imx_probe() info: why not propagate 'irq' from platform_get_irq() instead of (-2)?
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

For Exynos4 and Exynos5 SoCs from Samsung the i2c clock is based
on a fixed 66 MHz peripheral clock, and therefore is completely
independent of the cpu frequency.
Thus, registering for a CPU freq notifier is very wasteful.

This patch modifes the code such that, i2c bus registers to
cpu_freq_transition only if CONFIG_CPU_FREQ_S3C24XX is enabled.

This change should save a bunch of cpufreq transitions calls
which does not apply to exynos SoCs.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds polling mode support for i2c-s3c2410 driver.The
SATA PHY controller's CMU and TRSV block's are of I2C register
map in exynos5250.These blocks can be configured using i2c.

But i2c controller instance on which these block's sits lacks an
interrupt line.Also the current i2c-s3c2410 driver is only interrupt
driven, thus a polling mode support is required in the driver for
supporting this controller. This patch adds this support to the driver.
Signed-off-by: NVasanth Ananthan <vasanth.a@samsung.com>
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Hardware supported by the i2c sh_mobile and rcar drivers is only found
on SUPERH or ARCH_SHMOBILE platforms. Restrict non-COMPILE_TEST
compilation to them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Tested with a r7s72100 genmai board acessing an eeprom.
Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

In order to find I2C devices in the device tree, the platform nodes
have to be known by the I2C core. This requires setting the
dev.of_node parameter of the adapter.
Signed-off-by: NFlorian Meier <florian.meier@koalo.de>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.

Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: NVictor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: NTaras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Correct a typo that prevented the driver from being built as a module.
Reported-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NTim Kryger <tim.kryger@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The previous diolan adapter uses other out/in endpoints than
the current DLN-2-U2C in compatibility mode.
They changed from 0x2/0x84 to 0x3/0x83.
This patch gets the endpoints from the usb interface, instead
of hardcode them in the driver.

This was tested on a current DLN-2-U2C board.
Signed-off-by: NMartin Vogt <mvogt1@gmail.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: NMarkus Mayer <markus.mayer@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

I2C IP block expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.

Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: NTaras Kondratiuk <taras.kondratiuk@linaro.org>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Fix to return a negative error code from the bus speed parse
error handling case instead of 0.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: NTim Kryger <tim.kryger@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Using the i2c-eg20t driver and call i2cdetect or probe on the bus,
the driver will print a lot of error messages if there was no ACK
received.

i2cdetect normally print a table with all the available devices. If there
is no device on the address, the table will be empty.
Currently with the i2c-eg20t driver, the table is not visible because
the error messages destroy the table.

Error message: pch_i2c_getack return -71

This patch prevent the driver to print the messages to syslog.
The pch_i2c_wait_for_check_xfer function is the only one who is
calling pch_i2c_getack, so we can delete the function and add the
read to pch_i2c_wait_for_check_xfer.
If no ACK is received, the Message will be printed as a dbg
message.

Fixed print message to be a one liner so we can grep for the
error message.

Tested on Intel Atom E6xx and Eg20t Chipset.
Signed-off-by: NAndreas Werner <wernerandy@gmx.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Introduce support for Broadcom Serial Controller (BSC) I2C bus found
in the Kona family of Mobile SoCs.  FIFO hardware is utilized but only
standard mode (100kHz), fast mode (400kHz), fast mode plus (1MHz), and
I2C high-speed (3.4 MHz) bus speeds are supported.
Signed-off-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMatt Porter <matt.porter@linaro.org>
Reviewed-by: NMarkus Mayer <markus.mayer@linaro.org>
[wsa: fixed Kconfig sorting, squashed broken out patches into one]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

As we claim to support device tree for mach-omap2, we
should have the necessary flags in the driver to make it
usable.

Cc: linux-i2c@vger.kernel.org
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Looks like we're missing two lines needed to make it
work properly with device tree.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.

[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add the missing clk_disable_unprepare() before return
from wmt_i2c_reset_hardware() in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org # 3.11+

Newer Intel PCHs with LPSS have the same Designware I2C controllers than
Haswell but the ACPI IDs differ. Add these IDs to the driver list.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds the SMBus Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

clk_disable_unprepare in remove causes an imbalance and hence gives
the below crash on module remove. While at it also remove some
duplicate code from probe.

/ $ rmmod i2c-exynos5
[    6.996374] ------------[ cut here ]------------
[    6.999523] WARNING: CPU: 2 PID: 1137 at drivers/clk/clk.c:842 clk_disable+0x18/0x24()
[    7.007403] Modules linked in: i2c_exynos5(-)
[    7.011747] CPU: 2 PID: 1137 Comm: rmmod Not tainted 3.12.0-next-20131105-00083-g16f4799-dirty #21
[    7.020696] [<c0014e0c>] (unwind_backtrace+0x0/0xf4) from [<c0011784>] (show_stack+0x10/0x14)
[    7.029190] [<c0011784>] (show_stack+0x10/0x14) from [<c037acd4>] (dump_stack+0x7c/0xb0)
[    7.037255] [<c037acd4>] (dump_stack+0x7c/0xb0) from [<c001e0ac>] (warn_slowpath_common+0x6c/0x88)
[    7.046190] [<c001e0ac>] (warn_slowpath_common+0x6c/0x88) from [<c001e164>] (warn_slowpath_null+0x1c/0x24)
[    7.055818] [<c001e164>] (warn_slowpath_null+0x1c/0x24) from [<c02dcde4>] (clk_disable+0x18/0x24)
[    7.064670] [<c02dcde4>] (clk_disable+0x18/0x24) from [<bf0002d4>] (exynos5_i2c_remove+0x1c/0x34 [i2c_exynos5])
[    7.074736] [<bf0002d4>] (exynos5_i2c_remove+0x1c/0x34 [i2c_exynos5]) from [<c02274a8>] (__device_release_driver+0x58/0xb0)
[    7.085836] [<c02274a8>] (__device_release_driver+0x58/0xb0) from [<c0227b88>] (driver_detach+0xac/0xb0)
[    7.095291] [<c0227b88>] (driver_detach+0xac/0xb0) from [<c02271c0>] (bus_remove_driver+0x4c/0xa0)
[    7.104227] [<c02271c0>] (bus_remove_driver+0x4c/0xa0) from [<c00725dc>] (SyS_delete_module+0x124/0x194)
[    7.113682] [<c00725dc>] (SyS_delete_module+0x124/0x194) from [<c000e2e0>] (ret_fast_syscall+0x0/0x30)
[    7.122957] ---[ end trace 23bb6e4e0bf52196 ]---
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds support to SSC (Synchronous Serial Controller)
I2C driver. This IP also supports SPI protocol, but this is not
the aim of this driver.

This IP is embedded in all ST SoCs for Set-top box platorms, and
supports I2C Standard and Fast modes.
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Adds support for High Speed I2C driver found in Exynos5 and
later SoCs from Samsung.

Driver only supports Device Tree method.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: NTaekgyun Ko <taeggyun.ko@samsung.com>
Reviewed-by: NSimon Glass <sjg@google.com>
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: NAndrew Bresticker <abrestic@google.com>
[wsa: rebased to v3.12-rc4 (no of_i2c.h anymore)]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

b720423a
(i2c: rcar: add rcar-H2 support)
added R-Car H2 support on i2c-rcar.

The R-Car I2C type is based on SoC generation
(Gen1 = E1/M1/H1, Gen2 = E2/M2/H2),
but added naming was H1/H2 instead of Gen1/Gen2.
Gen1/Gen2 is better naming on this driver.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

"obj" can't be NULL here.

We already know that "pkg->package.elements" gives us a valid pointer
so the next pointer after that is also non-NULL.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>