When IRQs are shared by multiple controllers and if the first one
to register does not disable the IRQ, then IRQ will be enabled
for all other controllers by default, irrespective of their
setting. With IRQF_DISABLED registration, the driver interrupt
routine was called with interrupt enabled always. Disbaling the
registration with IRQF_DISABLED, since driver code is re-entrant
safe and all critical sections are guarded with interrupt safe
locks.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Interface allows for the update of onboard EDC firmware
present on mezzanine ISP25xx type cards.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

In handling the RMW semantics needed to update regions not
falling on a sector boundary.
Signed-off-by: NLalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

General cleanup of extraneous/legacy crud.

Additional cleanups and
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

For ISP24xx and above the ISP-abort after flash update is not
needed, as the only purpose it was serving was to update the boot
code and firmware versions in the scsi_qla_host_t structure.  Now
an update of the versions will be done in the write-vpd path.
Signed-off-by: NLalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NLalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Ensure that an ISP-abort has completed before performing any
update.  After the update do not wait for an ISP-abort completion,
instead just wait until the ISP is reset.  This avoids long
delays due to waiting for loop ready in qla2x00_abort_isp().
Signed-off-by: NLalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Given the low-level interface varies from one flash-part
manufacturer to the next, the Flash-Access-Control (FAC) mailbox
command makes the specific flash type transparent to the driver
by encapsulating a basic set of accessor and update routines.
Use these new routines where applicable by querying FAC opcode
get-sector-size at init-time.

Additional cleanups and
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Since the routines can/will use resources such as devices and
rports that aren't valid after midlayer tear-down, correct this
potential race, by stopping the offending during the early stages
of the remove() callback.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

As all commands queued on the physical HBA should be aborted and
returned to the upper-layers.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Reflects layout and format of latest specification.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Since in some circumstances, login-retries may be occuring in the
background via the DPC routine.  This race, in the inadvertant
setting of the loop-id to 'NONE' breaks the existing retry logic.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Recent ISPs use this data to configure FCF information.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

With recent ISPs loading firmware from flash, a flash-update to
the firmware-image region with a follow-on reset will reload the
new image.

Original caching of data only made sense when firmware was bound
with the driver.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The pcihdr variable is used to find valid boot code image to get
FC boot code versions from flash. The pcihdr variable should be
byte aligned.
Signed-off-by: NHarish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

fce_size should be calculated based on the FCE_SIZE #define.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Earlier refactoring codes missed passing the proper vha structure
and instead passed the 'hardware-descriptor' ha.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Post refactoring/multi-queue additions essentially eliminated the
need for separate ISP24XX+ queuecommand as isp_ops contains a
function pointer to the associated 'start_scsi()' operation.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Original code used an overabundance of indirect pointers to
function helpers.  Instead, the driver can exploit the immutable
properties of a queue's ISP-association and ID, which are both
known at queue initialization-time.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Bump driver version to 1.0.5.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The ibmvfc driver currently breaks the CRQ and essentially
resets the entire virtual FC adapter, killing all outstanding
ops to all attached targets, if an ADISC times out during target
discover/rediscovery. This patch adds some code to cancel the
ADISC if it times out, which prevents a single ADISC timeout from
affecting the other devices attached to the fabric.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Set show_host_maxframe_size so that maxframe_size gets exported in
sysfs for the host.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The ibmvfc driver really does not handle dynamically changing disc_threads.
To change this dynamically would cause confusion in the driver regarding
the number of event structs allocated. Fix this by simply not allowing
disc_threads to be changed at runtime.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch fixes a problem of possible dropped interrupts. Currently,
the ibmvfc driver has a race condition where after ibmvfc_interrupt
gets run, the platform code clears the interrupt. This can result in
lost interrupts and, in worst case scenarios, result in command
timeouts. Fix this by implementing a tasklet similar to what the
ibmvscsi driver does so that interrupt processing is no longer done in
the actual interrupt handler, which eliminates the race.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  Remove two unneeded exports and make two symbols static in fs/mpage.c
  Cleanup after commit 585d3bc0
  Trim includes of fdtable.h
  Don't crap into descriptor table in binfmt_som
  Trim includes in binfmt_elf
  Don't mess with descriptor table in load_elf_binary()
  Get rid of indirect include of fs_struct.h
  New helper - current_umask()
  check_unsafe_exec() doesn't care about signal handlers sharing
  New locking/refcounting for fs_struct
  Take fs_struct handling to new file (fs/fs_struct.c)
  Get rid of bumping fs_struct refcount in pivot_root(2)
  Kill unsharing fs_struct in __set_personality()

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (21 commits)
  drm/radeon: load the right microcode on rs780
  drm: remove unused "can_grow" parameter from drm_crtc_helper_initial_config
  drm: fix EDID backward compat check
  drm: sync the mode validation for INTERLACE/DBLSCAN
  drm: fix typo in edid vendor parsing.
  DRM: drm_crtc_helper.h doesn't actually need i2c.h
  drm: fix missing inline function on 32-bit powerpc.
  drm: Use pgprot_writecombine in GEM GTT mapping to get the right bits for !PAT.
  drm/i915: Add a spinlock to protect the active_list
  drm/i915: Fix SDVO TV support
  drm/i915: Fix SDVO CREATE_PREFERRED_INPUT_TIMING command
  drm/i915: Fix error in SDVO DTD and modeline convert
  drm/i915: Fix SDVO command debug function
  drm/i915: fix TV mode setting in property change
  drm/i915: only set TV mode when any property changed
  drm/i915: clean up udelay usage
  drm/i915: add VGA hotplug support for 945+
  drm/i915: correctly set IGD device's gtt size for KMS.
  drm/i915: avoid hanging on to a stale pointer to raw_edid.
  drm/i915: check for -EINVAL from vm_insert_pfn
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (54 commits)
  glge: remove unused #include <version.h>
  dnet: remove unused #include <version.h>
  tcp: miscounts due to tcp_fragment pcount reset
  tcp: add helper for counter tweaking due mid-wq change
  hso: fix for the 'invalid frame length' messages
  hso: fix for crash when unplugging the device
  fsl_pq_mdio: Fix compile failure
  fsl_pq_mdio: Revive UCC MDIO support
  ucc_geth: Pass proper device to DMA routines, otherwise oops happens
  i.MX31: Fixing cs89x0 network building to i.MX31ADS
  tc35815: Fix build error if NAPI enabled
  hso: add Vendor/Product ID's for new devices
  ucc_geth: Remove unused header
  gianfar: Remove unused header
  kaweth: Fix locking to be SMP-safe
  net: allow multiple dev per napi with GRO
  r8169: reset IntrStatus after chip reset
  ixgbe: Fix potential memory leak/driver panic issue while setting up Tx & Rx ring parameters
  ixgbe: fix ethtool -A|a behavior
  ixgbe: Patch to fix driver panic while freeing up tx & rx resources
  ...

Fix slab corruption caused by alloc_cpumask_var_node() overwriting the
tail end of an off-stack cpumask.

The function zeros out cpumask bits beyond the last possible cpu.  The
starting point for zeroing should be the beginning of the mask offset by a
byte count derived from the number of possible cpus.  The offset was
calculated in bits instead of bytes.  This resulted in overwriting the end
of the cpumask.
Signed-off-by: NJack Steiner <steiner@sgi.com>
Acked-by: Mike Travis <travis.sgi.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: <stable@kernel.org>		[2.6.29.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implement __raw_read_lock_flags and __raw_write_lock_flags for the ia64
architecture.

[kosaki.motohiro@jp.fujitsu.com: typo fix]
Signed-off-by: NPetr Tesarik <ptesarik@suse.cz>
Signed-off-by: NRobin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NTony Luck <tony.luck@intel.com>
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pass the original flags to rwlock arch-code, so that it can re-enable
interrupts if implemented for that architecture.

Initially, make __raw_read_lock_flags and __raw_write_lock_flags stubs
which just do the same thing as non-flags variants.
Signed-off-by: NPetr Tesarik <ptesarik@suse.cz>
Signed-off-by: NRobin Holt <holt@sgi.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SGI has observed that on large systems, interrupts are not serviced for a
long period of time when waiting for a rwlock.  The following patch series
re-enables irqs while waiting for the lock, resembling the code which is
already there for spinlocks.

I only made the ia64 version, because the patch adds some overhead to the
fast path.  I assume there is currently no demand to have this for other
architectures, because the systems are not so large.  Of course, the
possibility to implement raw_{read|write}_lock_flags for any architecture
is still there.

This patch:

The new macro LOCK_CONTENDED_FLAGS expands to the correct implementation
depending on the config options, so that IRQ's are re-enabled when
possible, but they remain disabled if CONFIG_LOCKDEP is set.
Signed-off-by: NPetr Tesarik <ptesarik@suse.cz>
Signed-off-by: NRobin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make ufs return f_fsid info for statfs(2).
Signed-off-by: NColy Li <coly.li@suse.de>
Cc: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make sysv file system return f_fsid info for statfs(2).
Signed-off-by: NColy Li <coly.li@suse.de>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make squashfs return f_fsid info for statfs(2).
Signed-off-by: NColy Li <coly.li@suse.de>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make reiserfs3 return f_fsid info for statfs(2).  By Andreas' suggestion,
this patch populates a persistent f_fsid between boots/mounts with help of
on-disk uuid record.

Randy Dunlap reported a compiling error from v2 patch like:
    fs/built-in.o: In function `reiserfs_statfs':
    super.c:(.text+0x7332b): undefined reference to `crc32_le'
    super.c:(.text+0x7333f): undefined reference to `crc32_le'
Also he provided helpful solution to fix this error. The modification of v3
patch is based on Randy's suggestion, add 'select CRC32' in fs/reiserfs/Kconfig.
Signed-off-by: NColy Li <coly.li@suse.de>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make qnx4 file system return f_fsid info for statfs(2).
Signed-off-by: NColy Li <coly.li@suse.de>
Acked-by: NAnders Larsen <al@alarsen.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make omfs return f_fsid info for statfs(2).
Signed-off-by: NColy Li <coly.li@suse.de>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make minix file system return f_fsid info for statfs(2).
Signed-off-by: NColy Li <coly.li@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make isofs return f_fsid info for statfs(2).
Signed-off-by: NColy Li <coly.li@suse.de>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make hpfs return f_fsid info for statfs(2).
Signed-off-by: NColy Li <coly.li@suse.de>
Cc: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>