Simple round-robin hardware TX scheduling can cause starvation of TX rings
with small packets when other TX rings have large TSO or jumbo packets.

In the simplest case, consider 2 TCP streams running in opposite
directions.  The TSO TX traffic will hash to one ring and the ACKs for the
incoming data on a different TCP connection will hash to a different TX
ring.  The hardware fetches one complete TSO packet (up to 64K data)
before servicing the other TX ring.  When it gets to the other TX ring, it
will only fetch one packet (64-byte ACK packet in this case).  After that,
it will switch back to the 1st ring filled with more TSO packets.  Because
only one ACK can go out roughly every 500 usec in this case, the incoming
data rate becomes very low.

Update version to 3.125.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Default remains the same.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

by introducing tg3_stop() that does the opposite of tg3_start().  This
function will be useful when adding the support for changing the numbe
of rx and tx rings.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

by introducing tg3_start() that handles all initialization steps from
IRQ allocation.  This function will be needed when adding support for
changing the number of rx and tx rings.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

since the number of rings can be different.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

irq_cnt is no longer necessarily equal to the number rx or tx rings.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is preparation work to allow the number of RX and TX rings to be
configured separately.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, the function of_phy_connect() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 51af6d7c.

Breaks the build with CONFIG_PCI_ATS not enabled.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the device close path, 'qlcnic_fw_destroy_ctx' and
'qlcnic_poll_rsp' call msleep. But  'qlcnic_fw_destroy_ctx' and
'qlcnic_poll_rsp' are called with 'adapter->tx_clean_lock' spin lock
held resulting in scheduling while atomic bug causing the following
trace.

I observed that the commit 012dc19a
from John Fastabend addresses a similar issue in ixgbevf driver.
Adopting the same approach used in the commit, this patch uses mdelay
to address the issue.

[79884.999115] BUG: scheduling while atomic: ip/30846/0x00000002
[79885.005562] INFO: lockdep is turned off.
[79885.009958] Modules linked in: qlcnic fuse nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE bnep bluetooth rfkill ip6table_mangle ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables iptable_nat nf_nat iptable_mangle ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack iptable_filter ip_tables dcdbas coretemp kvm_intel kvm iTCO_wdt ixgbe iTCO_vendor_support crc32c_intel ghash_clmulni_intel nfsd microcode sb_edac pcspkr edac_core dca bnx2x shpchp auth_rpcgss nfs_acl lpc_ich mfd_core mdio lockd libcrc32c wmi acpi_pad acpi_power_meter sunrpc uinput sd_mod sr_mod cdrom crc_t10dif ahci libahci libata megaraid_sas usb_storage dm_mirror dm_region_hash dm_log dm_mod [last unloaded: qlcnic]
[79885.083608] Pid: 30846, comm: ip Tainted: G        W  O 3.6.0-rc7+ #1
[79885.090805] Call Trace:
[79885.093569]  [<ffffffff816764d8>] __schedule_bug+0x68/0x76
[79885.099699]  [<ffffffff8168358e>] __schedule+0x99e/0xa00
[79885.105634]  [<ffffffff81683929>] schedule+0x29/0x70
[79885.111186]  [<ffffffff81680def>] schedule_timeout+0x16f/0x350
[79885.117724]  [<ffffffff811afb7a>] ? init_object+0x4a/0x90
[79885.123770]  [<ffffffff8107c190>] ? __internal_add_timer+0x140/0x140
[79885.130873]  [<ffffffff81680fee>] schedule_timeout_uninterruptible+0x1e/0x20
[79885.138773]  [<ffffffff8107e830>] msleep+0x20/0x30
[79885.144159]  [<ffffffffa04c7fbf>] qlcnic_issue_cmd+0xef/0x290 [qlcnic]
[79885.151478]  [<ffffffffa04c8265>] qlcnic_fw_cmd_destroy_rx_ctx+0x55/0x90 [qlcnic]
[79885.159868]  [<ffffffffa04c92fd>] qlcnic_fw_destroy_ctx+0x2d/0xa0 [qlcnic]
[79885.167576]  [<ffffffffa04bf2ed>] __qlcnic_down+0x11d/0x180 [qlcnic]
[79885.174708]  [<ffffffffa04bf6f8>] qlcnic_close+0x18/0x20 [qlcnic]
[79885.181547]  [<ffffffff8153b4c5>] __dev_close_many+0x95/0xe0
[79885.187899]  [<ffffffff8153b548>] __dev_close+0x38/0x50
[79885.193761]  [<ffffffff81545101>] __dev_change_flags+0xa1/0x180
[79885.200419]  [<ffffffff81545298>] dev_change_flags+0x28/0x70
[79885.206779]  [<ffffffff815531b8>] do_setlink+0x378/0xa00
[79885.212731]  [<ffffffff81354fe1>] ? nla_parse+0x31/0xe0
[79885.218612]  [<ffffffff815558ee>] rtnl_newlink+0x37e/0x560
[79885.224768]  [<ffffffff812cfa19>] ? selinux_capable+0x39/0x50
[79885.231217]  [<ffffffff812cbf98>] ? security_capable+0x18/0x20
[79885.237765]  [<ffffffff81555114>] rtnetlink_rcv_msg+0x114/0x2f0
[79885.244412]  [<ffffffff81551f87>] ? rtnl_lock+0x17/0x20
[79885.250280]  [<ffffffff81551f87>] ? rtnl_lock+0x17/0x20
[79885.256148]  [<ffffffff81555000>] ? __rtnl_unlock+0x20/0x20
[79885.262413]  [<ffffffff81570fc1>] netlink_rcv_skb+0xa1/0xb0
[79885.268661]  [<ffffffff81551fb5>] rtnetlink_rcv+0x25/0x40
[79885.274727]  [<ffffffff815708bd>] netlink_unicast+0x19d/0x220
[79885.281146]  [<ffffffff81570c45>] netlink_sendmsg+0x305/0x3f0
[79885.287595]  [<ffffffff8152b188>] ? sock_update_classid+0x148/0x2e0
[79885.294650]  [<ffffffff81525c2c>] sock_sendmsg+0xbc/0xf0
[79885.300600]  [<ffffffff8152600c>] __sys_sendmsg+0x3ac/0x3c0
[79885.306853]  [<ffffffff8109be23>] ? up_read+0x23/0x40
[79885.312510]  [<ffffffff816896cc>] ? do_page_fault+0x2bc/0x570
[79885.318968]  [<ffffffff81191854>] ? sys_brk+0x44/0x150
[79885.324715]  [<ffffffff811c458c>] ? fget_light+0x24c/0x520
[79885.330875]  [<ffffffff815286f9>] sys_sendmsg+0x49/0x90
[79885.336707]  [<ffffffff8168e429>] system_call_fastpath+0x16/0x1b
Signed-off-by: NNarendra K <narendra_k@dell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit c0357e97 modified bnx2 to switch from
using ioremap/iounmap to pci_iomap/pci_iounmap.  They missed a spot in the error
path of bnx2_init_one though.  This patch just cleans that up.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Michael Chan <mcan@broadcom.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GCC can't see that in all non-error-return paths we do in fact
set *using_dac to something.

Add an explicit initialization to remove this warning:

drivers/net/ethernet/brocade/bna/bnad.c: In function ‘bnad_pci_probe’:
drivers/net/ethernet/brocade/bna/bnad.c:3079:5: warning: ‘using_dac’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/brocade/bna/bnad.c:3233:7: note: ‘using_dac’ was declared here
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current VFs enumeration algorithm used in be_find_vfs does not take domain
number into the match. The match found in igb/ixgbe is more elegant and
safe.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new common code routine to upgrade an adapter's
firmware.  This routine handles all of the complexities of working with the
the existing adapter firmware in order to quiesce the adapter and uP, etc.
For an automatic upgrade it will send a HELLO command to check if cxgb4
want/can upgrade firmware, i.e. if cxgb4 is MASTER and has newer firmware
that it wants to load and call the new common code routine t4_fw_upgrade.
Note that it should not issue a RESET command after a successful firmware
upgrade.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a card had already been initialized, on reloading cxgb4 driver firmware
required an upgrade but the upgrade did not happen. In that case a mailbox
timeout would occur during T4 configuration file stuff. The fix is to let the
caller know the firmware was not upgraded so a reset would be issued before
starting the T4 config stuff.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case if user defined configuration file at /lib/firmware/cxgb4/t4-config.txt
location and also factory default configuration file written to FLASH are not
present then driver will use hardwired configuration settings.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Starting with T4 firmware version 1.3.11.0 the firmware now supports device
configuration via a Firmware Configuration File. The Firmware Configuration
File was primarily developed in order to centralize all of the configuration,
resource allocation, etc. for Unified Wire operation where multiple
Physical / Virtual Function Drivers would be using a T4 adapter simultaneously.

The Firmware Configuration file can live in three locations as shown below
in order of precedence.
1) User defined configuration file: /lib/firmware/cxgb4/t4-config.txt
2) Factory Default configuration file written to FLASH within
   the manufacturing process.
3) Hardwired driver configuration.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds new enums and macros to enable T4 configuration file support. It
also removes duplicate macro definitions.

It fixes the build failure in cxgb4vf driver introduced because of old macro
definition removal.

It also performs SGE initialization based on T4 configuration file is provided
or not. If it is provided then it uses the parameters provided in it otherwise
it uses hard coded values.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements two new functions t4_mem_win_read and t4_memory_read.
These new functions can be used to read memory via the PCIE memory window.
Please note, for proper execution of these functions PCIE_MEM_ACCESS_BASE_WIN
registers must be setup correctly like how setup_memwin in the cxgb4 driver
does it.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, the function of_phy_connect() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MIPSsim platform is no longer supported or used. This patch
deletes the Ethernet driver.
Signed-off-by: NSteven J. Hill <sjhill@mips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is primarily to address transmission timeout occurrences, when
multiple H/W Tx queues are being used concurrently. Because in
the priority scheduling mode the controller does not service the
Tx queues equally (but in ascending index order), Tx timeouts are
being triggered rightaway for a basic test with multiple simultaneous
connections like:
iperf -c <server_ip> -n 100M -P 8

resulting in kernel trace:
NETDEV WATCHDOG: eth1 (fsl-gianfar): transmit queue <X> timed out
------------[ cut here ]------------
WARNING: at net/sched/sch_generic.c:255
...
and controller reset during intense traffic, and possibly further
complications.

This patch changes the default H/W Tx scheduling setting (TXSCHED)
for multi-queue devices, from priority scheduling mode to a weighted
round robin mode with equal weights for all H/W Tx queues, and
addresses the issue above.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the definition of bnx2x_tests_str_arr from static char
pointer to static const char bi-directional array. Also the
bnx2x_get_strings function is simplified.
Reported-by: NJoe Perches <joe@perches.com>
Reported-by: NDavid Laight <David.Laight@ACULAB.COM>
Signed-off-by: NMerav Sicron <meravs@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With recent kernel changes we can now return errors on a failure to setup a
VLAN filter.  This patch takes advantage of that opportunity so that we can
return either an EIO error in the case of a mailbox failure, or an EACCESS
error in the case of being denied access to the VLAN filter table by the
PF.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRobert Garrett <robertx.e.garrett@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes the ixgbevf driver so that it can correctly drop a frame
should it receive a jumbo frame.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While fixing up a patch from Alex Duyck to use q_vectors in ring containers
to update the ITR I bungled it and missed actually updating the counters
in the ring container q_vectors.  This patch fixes my mistake and makes
interrupt moderation actually work.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove 'rx_ring' parameter as it is not used in ixgbevf_receive_skb
Signed-off-by: NNarendra K <narendra_k@dell.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The counter is not valid unless the controller is running in IOV mode.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF driver was not designed to correctly handle a message timeout.  As
a result it is possible for one bad message to invalidate all messages
following it until the part is reset.  Instead we should copy the example
in igbvf of how to handle a mailbox event and message timeout.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We're now using isa_virt_to_bus(), and there really
isn't a generic and consistent test for whether a
platform provides this interface or not.

This driver is also for an x86-only device.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PTP Hardware Clock devices appear as class devices in sysfs. This patch
changes the registration API to use the parent device, clarifying the
clock's relationship to the underlying device.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change is meant to improve performance on systems that do not require
the DMA unmap calls.  On those systems we do not need to make use of the
unmap address for Tx or the unmap length so we can drop both thereby
reducing the size of the Tx buffer info structure.

In addition I have changed the logic to check for unmap length instead of
unmap address when checking to see if a buffer needs to be unmapped from
DMA use.  The reasons for this change is that on some platforms it is
possible to receive a valid DMA address of 0 from an IOMMU.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of storing the RSS key as a character array we can simplify the
configuration by making it a u32 array.  This allows us to just write one
value per register without any unnecessary operations to construct the
value.

This change will produce the same exact key, the only difference is that I
translated the u8 array to a u32 array which will be correctly ordered on
writes to hardware by the cpu_to_le32 operations that are built into the
writel calls.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up our RSS indirection table configuration so that we
generate the same table regardless of CPU endianness.  In addition it
changes the table setup so that instead of doing a modulo based setup it is
instead a divisor based setup.  The advantage to this is that we should be
able to take the Rx hash and compute the Rx queue with very little CPU
overhead if needed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that Tx cleanup is done in a do/while loop instead
of a for loop.  The main motivation behind this is the fact that we should
never be invoked with a budget less than 1 so we can skip checking the
budget before processing the first descriptor.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change removes the code that was doing the NUMA allocations for the
q_vectors, rings, and ring resources.  The problem is the logic used assumed
that the NUMA nodes were always interleved and that is not always the case.

At some point I hope to add this functionality back in a more controlled
manner in the future.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to a hardware issue, on i210 and i211 parts, the TNCRS statistic
provides an invalid value.  This patch changes the update stats function
to increment the stat only for non-i210/i211 parts.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adapt the pre-existing and assigned VFs code to the ixgbe way introduced
in commit 9297127b.

Instead of searching the enabled VFs we use pci_num_vf to determine enabled VFs.
By comparing to which PF an assigned VF is owned it's possible to decide
whether to leave it enabled or not.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NRobert Garrett <robertx.e.garrett@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit eb716c54 ("sunbmac: remove
unnecessary setting of skb->dev") caused the local varible 'dev'
in bigmac_init_rings to become unused.  And now the compiler
warns about it.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>