Since the iop32x code isn't iop321-specific, and the iop33x code isn't
iop331-specfic, do a s/iop321/iop32x/ and s/iop331/iop33x/, and tidy up
the code to conform to the coding style guidelines somewhat better.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Factor out the register defines for a number of other peripherals
common to the iop32x and iop33x.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Revamp the iop3xx board support: move the support code for each iop
board type into its own file, start using platform serial and platform
physmap flash devices, switch to a per-board time tick rate, and get
rid of the ARCH_EP80219 and STEPD config options by doing the relevant
checks at run time.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Squeeze three instructions out of the iop32x irq demuxer, and nine
out of the iop33x irq demuxer by using the hardware vector generator.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The iop33x loadsp hunk in arch/arm/boot/compressed/head.S serves
no purpose -- remove it.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Implement the gpio_line_{config,get,set} API for iop3xx.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Get rid of the unused IOP3??_IRQ_OFS irq offset define, start IRQ
numbering from zero.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add CP6 enable/disable sequences to the timekeeping code and the IRQ
code.  As a result, we can't depend on CP6 access being enabled when
we enter get_irqnr_and_base anymore, so switch the latter over to
using memory-mapped accesses for now.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add macros to enable and disable access to CP6.  On the iop3xx, enabling
CP6 access unfortunately also enables access to that coprocessor from
unprivileged code, so we need these macros to enable and disable access
to the coprocessor whenever we need to access it.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Switch the iop32x and iop33x code over to the common time implementation,
and remove the (nearly identical) iop32x and iop33x time implementations.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Merge and rewrite the iop32x/iop33x time code to do lost jiffy
tracking properly, and put the result in plat-iop/time.c.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Switch the iop32x and iop33x code over to the common PCI implementation,
and remove the (nearly identical) iop32x and iop33x PCI implementations.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Merge the iop32x PCI code and iop33x PCI code into plat-iop/pci.c.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the i2c bits shared between iop32x and iop33x to plat-iop/i2c.c
and include/asm-arm/hardware/iop3xx.h.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Introduce the arch/arm/plat-iop directory, for code shared between the
iop32x and iop33x, and move the common memory map setup bits there.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Split the iop3xx mach type into iop32x and iop33x -- split the config
symbols, and move the code in the mach-iop3xx directory to the mach-iop32x
and mach-iop33x directories.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rename CONFIG_ARCH_IOP321 to CONFIG_ARCH_IOP32X and
CONFIG_ARCH_IOP331 to CONFIG_ARCH_IOP33X.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Clear both the EINT and INT status before
going to sleep, otherwise we may end up being
woken by something that was not set in our
wakeup map.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The s3c24xx_va_gpio2 variable is only used
when the S3C2412 and another cpu-type is
being used in the kernel. This patch ensures
it is not set when it is not being used.

Fixes bug report by Thomas Gleixner.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove the S3C2410 specific items out of the
core PM code. Add sysdev driver for all the
S3C24XX series that used the S3C2410 PM code.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

DMA channel mappings for the S3C2312
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On stepping A0/A1 of the 80200, invalidating D-cache by line doesn't
clear the dirty bits, which means that if we invalidate a dirty line,
the dirty data can still be written back to memory later on.

To work around this, dma_inv_range() on these two processors is
implemented as dma_flush_range() (i.e. do a clean D-cache line before
doing the invalidate D-cache line.)  For this, we currently have a
processor ID check in xscale_dma_inv_range(), but a better solution
is to add a separate cache_fns and proc_info for A0/A1 80200.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Prevent userland from mapping in physical address regions >= 4G by
checking for that in valid_mmap_phys_addr_range().

Unfortunately, we cannot override valid_mmap_phys_addr_range() without
also overriding valid_phys_addr_range(), so copy drivers/char/mem.c's
version of valid_phys_addr_range() over to arch/arm/mm/mmap.c as well.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add Cirrus Logic EDB9312 support.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that we have raw_* variants of local_irq_$FOO(), switch the atomic
helpers over to use those raw_* variants.  This is necessary when using
lockdep on pre-ARMv6 hardware, as lockdep uses atomic_t counters in the
trace_hardirqs_off() path.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add LCD register definitions for the S3C2412.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add LCD register definitions for the S3C2442.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Change to using flush_cache_all() in pm.c and
also remove the need to flush the cache in the
PM code.

This changes the sleep.S code to have an entry
to store the registers for resume, and then a
second entry (after the caches are cleaned)
to do the suspend and resume.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Seperate the IRQ power management code out of
the pm.c file, and add it to the relevant
system class devices.

Also make the suspend and resume code take
notice of the fact these registers can be
moved by compile time code.

Add fix from Ilya Yanok to also save the
INTSUBMSK over sleep.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

DMA channel mappings for the S3C2442
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

S3C2440 DMA channel mappings
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

DMA channel mappings for the S3C2410
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Allow each CPU type in the S3C24XX range to
select the DMA channel mapping it supports.

We change the DMA registration to use an
virtual channel number that the DMA system
will allocate to a hardware channel at
request time.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add base definitions for the AC97 register
definitions.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Create header with uClinux flat format binary support macros for ARM
platforms. Derived from the m68knommu flat.h.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Daniel Jacobowitz

The ARM kernel has several uses of asm("foo%?").  %? is a GCC internal
modifier used to output conditional execution predicates.  However, no
version of GCC supports conditionalizing asm statements.  GCC 4.2 will
correctly expand %? to the empty string in user asms.  Earlier versions may
reuse the condition from the previous instruction.  In 'if (foo) asm
("bar%?");' this is somewhat likely to be right... but not reliable.

So, the only safe thing to do is to remove the uses of %?.  I believe
the tlbflush.h occurances were supposed to be removed before, based
on the comment about %? not working at the top of that file.

Old versions of GCC could omit branches around user asms if the asm didn't
mark the condition codes as clobbered.  This problem hasn't been seen on any
recent (3.x or 4.x) GCC, but it could theoretically happen.  So, where
%? was removed a cc clobber was added.
Signed-off-by: NDaniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The common case for the thread notifier is a context switch.  Tell
gcc that this is the most likely condition so it can optimise the
function for this case.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

ARM has interrupts enabled over context switches (iow, has
__ARCH_WANT_INTERRUPTS_ON_CTXSW defined.)  The lockdep code in fork.c
 assumes that interrupts are always disabled.  Fix this wrong
assumption by making the initialisation of 'p->hardirqs_enabled'
depend on __ARCH_WANT_INTERRUPTS_ON_CTXSW.
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This adds support for irqtrace for lockdep on ARM.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rename mmu.c to context.c - it's the ARMv6 ASID context handling
code rather than generic "mmu" handling code.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>