On architectures that have a cache line size larger than 64 Bytes we start
running into issues where the amount of headroom for the frame starts
shrinking.

The size of skb_shared_info on a system with a 64B L1 cache line size is
320.  This increases to 384 with a 128B cache line, and 512 with a 256B
cache line.

In addition the NET_SKB_PAD value increases as well consistent with the
cache line size.  As a result when we get to a 256B cache line as seen on
the s390 we end up 768 bytes used by padding and shared info leaving us
with only 1280 bytes to use for data storage.  On architectures such as
this we should default to using 3K Rx buffers out of a 8K page instead of
trying to do 1.5K buffers out of a 4K page.

To take all of this into account I have added one small check so that we
compare the max_frame to the amount of actual data we can store.  This was
already occurring for igb, but I had overlooked it for ixgbe as it doesn't
have strict limits for 82599 once we enable jumbo frames.  By adding this
check we will automatically enable 3K Rx buffers as soon as the maximum
frame size we can handle drops below the standard Ethernet MTU.

I also went through and fixed one small typo that I found where I had left
an IGB in a variable name due to a copy/paste error.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently ixgbe_set_rxfh() updates the rss_key copy in the driver
memory, but does not push the new value into the h/w. This commit
add a new helper for the latter operation and call it in
ixgbe_set_rxfh(), so that the h/w rss key value can be really
updated via ethtool.
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes it so that we don't need to bother with clearing the
memory out for the descriptor rings.  The general idea is to only free
buffers associated with buffers in use which are located between the
next_to_clean and next_to_use or next_to_alloc values.  Everything outside
of those regions can be safely ignored since they should have no buffers
associated with them.

The advantage to doing things this way is that is should speed up bring-up
and tear-down of the rings.  Specifically we can avoid the 512 or more
cycles required to memset the rings in tear-down.  In the bring-up phase we
then clear the memory as a part of initialization.  The general idea is
that the clearing in initialization can act as a prefetch of sorts for the
buffer info structures so they are in the local CPU when we go to populate
them.  This should help to improve overall time needed to perform a
suspend/resume.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds build_skb support to the Rx path.  There are several
advantages to this change.

1.  It avoids the memcpy and skb->head allocation for small packets which
    improves performance by about 5% in my tests.
2.  It avoids the memcpy, skb->head allocation, and eth_get_headlen
    for larger packets improving performance by about 10% in my tests.
3.  For VXLAN packets it allows the full header to be in skb->data which
    improves the performance by as much as 30% in some of my tests.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for providing a buffer with headroom and tailroom
to allow for shared info, NET_SKB_PAD, and NET_IP_ALIGN.  With this
combined with the DMA changes we can start using build_skb to build frames
around an incoming Rx buffer instead of having to memcpy the headers.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We are going to be expanding the number of Rx paths in the driver.  Instead
of duplicating all that code I am pulling it apart into separate functions
so that we don't have so much code duplication.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to support build_skb with jumbo frames it will be necessary to use
3K buffers for the Rx path with 8K pages backing them.  This is needed on
architectures that implement 4K pages because we can't support 2K buffers
plus padding in a 4K page.

In the case of systems that support page sizes larger than 4K the 3K
attribute will only be applied to FCoE as we can fall back to using just 2K
buffers and adding the padding.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Batch the page count updates instead of doing them one at a time.  By doing
this we can improve the overall performance as the atomic increment
operations can be expensive due to the fact that on x86 they are locked
operations which can cause stalls.  By doing bulk updates we can
consolidate the stall which should help to improve the overall receive
performance.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for DMA_ATTR_SKIP_CPU_SYNC and
DMA_ATTR_WEAK_ORDERING.  By enabling both of these for the Rx path we are
able to see performance improvements on architectures that implement either
one due to the fact that page mapping and unmapping only has to sync what
is actually being used instead of the entire buffer.  In addition by
enabling the weak ordering attribute enables a performance improvement for
architectures that can associate a memory ordering with a DMA buffer such
as Sparc.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On some platforms, syncing a buffer for DMA is expensive. Rather than
sync the whole 2K receive buffer, only synchronise the length of the
frame, which will typically be the MTU, or a much smaller TCP ACK.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch consolidates the code for the ixgbe driver so that it is more
inline with what is already in igb.  The general idea is to just
consolidate functions that represent logical steps in the Rx process so we
can later update them more easily.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the driver version to reflect the new devices that it
supports.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since dcbnl_ops is global, it should be prefixed by ixgbe_
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.

Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f242738 ("bonding: use last_arp_rx in slave_last_rx()").

However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.

Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080d ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.

Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.

Compile-tested with allyesconfig and allmodconfig on x86 and arm.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NEric Dumazet <edumazet@google.com>
Reviewed-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.

Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement support for devices that have firmware-controlled PHYs.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure that we free the IRQs in ixgbe_io_error_detected() when
responding to an PCIe AER error and also restore them when the
interface recovers from it.

Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
in the case where we call ixgbe_remove() after a failed recovery from
AER error because the interrupts were not freed.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When an interface is part of a namespace it is possible that
ixgbe_close() may be called while __ixgbe_shutdown() is running
which ends up in a double free WARN and/or a BUG in free_msi_irqs().

To handle this situation we extend the rtnl_lock() to protect the
call to netif_device_detach() and ixgbe_clear_interrupt_scheme()
in __ixgbe_shutdown() and check for netif_device_present()
to avoid clearing the interrupts second time in ixgbe_close();

Also extend the rtnl lock in ixgbe_resume() to netif_device_attach().
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some x550 devices require the driver version reported to its firmware; this
patch sends the driver version string to the firmware through the host
interface command for x550 devices.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the case of IPIP and SIT tunnel frames the outer transport header
offset is actually set to the same offset as the inner transport header.
This results in the lco_csum call not doing any checksum computation over
the inner IPv4/v6 header data.

In order to account for that I am updating the code so that we determine
the location to start the checksum ourselves based on the location of the
IPv4 header and the length.

Fixes: b83e3010 ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some Tx paths (e.g., tpacket_snd()), ixgbe_atr may be
passed down an sk_buff that has the network and transport
header in the paged data, so it needs to make sure these
headers are available in the headlen bytes to calculate the
l4_proto.

This patch expect that network and transport headers are
already available in the non-paged header dat.  The assumption
is that the caller has set this up if l4_proto based Tx
steering is desired.
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 9f12df90 ("ixgbe: Store VXLAN port number in network order")
incorrectly checks for hdr.ipv4->protocol != IPPROTO_UDP
in ixgbe_atr(). This check should be for "==" instead.
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix an issue where set_phy_power was NULL for X550 copper devices
because get_invariants was called before hw->device_id was set.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Introduce ixgbe_link_operations struct with the following changes:

	read_i2c_combined		=> read_link
	read_i2c_combined_unlocked	=> read_link_unlocked
	write_i2c_combined		=> write_link
	write_i2c_combined_unlocked	=> write_link_unlocked

This will allow X550EM_a to override these methods for MDIO access
while X550EM_x provides methods to use I2C combined access. This
also adds a new structure, ixgbe_link_info, to hold information
about the link. Initially this is just method pointers and a bus
address.

The functions involved in combined I2C accesses were moved from
ixgbe_phy.c to ixgbe_x550.c. The underlying functions that carry
out the combined I2C accesses were left in ixgbe_phy.c because
they share some functions with other I2C methods.

v2 - set hw->link.ops in probe.
v3 - check ii->link_ops before setting it since we don't have it
for all devices.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The msix_entries memory can be freed by a previous suspend or
remove, so don't crash on close when it isn't there.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix NULL pointer dereference in the case where a macvlan interface is
brought up while the PF is still down:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: [<ffffffffa0170fb2>] ixgbe_alloc_rx_buffers+0x42/0x1a0 [ixgbe]

Call Trace:
[<ffffffffa017336b>] ixgbe_configure_rx_ring+0x2eb/0x3d0 [ixgbe]
[<ffffffffa0173811>] ixgbe_fwd_ring_up+0xd1/0x380 [ixgbe]
[<ffffffffa0179709>] ixgbe_fwd_add+0x149/0x230 [ixgbe]
[<ffffffffa0113480>] macvlan_open+0x260/0x2b0 [macvlan]
Reported-by: NMatthew Garrett <mjg59@coreos.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Convert ixgbe users to new dev walk API. This is just a code conversion;
no functional change is intended.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
  and no longer serves a purpose. No need to set min_mtu or max_mtu
  explicitly, as ether_setup() will already set them to 68 and 1500.

e1000: min_mtu 46, max_mtu 16110

e1000e: min_mtu 68, max_mtu varies based on adapter

fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now

i40e: min_mtu 68, max_mtu 9706

i40evf: min_mtu 68, max_mtu 9706

igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
  the driver, the larger value wasn't relevant though, so I've set max_mtu
  to the smaller of the two values here to retain identical behavior.

igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated

ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu

ixgbe: min_mtu 68, max_mtu 9710

ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710

CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These accessors are used in various drivers that support tc offloading,
to detect properties of a given 'tc_action'.

'is_tcf_mirred_redirect' tests that the action is TCA_EGRESS_REDIR.
'is_tcf_mirred_mirror' tests that the action is TCA_EGRESS_MIRROR.

As a prep towards supporting INGRESS redir/mirror, rename these
predicates to reflect their true meaning:
  s/is_tcf_mirred_redirect/is_tcf_mirred_egress_redirect/
  s/is_tcf_mirred_mirror/is_tcf_mirred_egress_mirror/
Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of limiting the VFs if we don't use 4 queues for RSS in the PF we
can instead just limit the RSS queues used to a power of 2.  By doing this
we can support use cases where VFs are using more queues than the PF is
currently using and can support RSS if so desired.

The only limitation on this is that we cannot support 3 queues of RSS in
the PF or VF.  In either of these cases we should fall back to 2 queues in
order to be able to use the power of 2 masking provided by the psrtype
register.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Simplify the logic for setting VLNCTRL.VFE by checking the  VMDQ flag
and 82598 MAC instead of having to maintain a list of MAC types.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for the new copper device X557.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add geneve Rx offload support for x550em_a.

The implementation follows the vxlan code with the lower 16 bits of
the VXLANCTRL register holding the UDP port for VXLAN and the upper
for Geneve.

Disabled NFS filters in the RFCTL register which allows us to simplify
the check for VXLAN and Geneve packets in ixgbe_rx_checksum().

Removed vxlan from the name of the callback functions and replaced it
with udp_tunnel which is more in line with the new API.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use atomic bitwise operations when setting and checking reset
requests. This should help with possible races in the service task.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Following a write the TXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As pointed out by Jamal, an action could be shared by
multiple filters, so we can't use list to chain them
any more after we get rid of the original tc_action.
Instead, we could just save pointers to these actions
in tcf_exts, since they are refcount'ed, so convert
the list to an array of pointers.

The "ugly" part is the action API still accepts list
as a parameter, I just introduce a helper function to
convert the array of pointers to a list, instead of
relying on the C99 feature to iterate the array.

Fixes: a85a970a ("net_sched: move tc_action into tcf_common")
Reported-by: NJamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Back when I submitted the GSO code I messed up and dropped the support for
disabling the VLAN tag filtering via the feature bit.  This patch
re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the
VLAN filtering independent of toggling promiscuous mode.

Fixes: b83e3010 ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When I was adding the code for enabling VLAN promiscuous mode with SR-IOV
enabled I had inadvertently left the VLNCTRL.VFE bit unchanged as I has
assumed there was code in another path that was setting it when we enabled
SR-IOV.  This wasn't the case and as a result we were just disabling VLAN
filtering for all the VFs apparently.

Also the previous patches were always clearing CFIEN which was always set
to 0 by the hardware anyway so I am dropping the redundant bit clearing.

Fixes: 16369564 ("ixgbe: Add support for VLAN promiscuous with SR-IOV")
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>