we never allocate a TRB pool for physical endpoints
0 and 1 so trying to free it (a invalid TRB pool pointer)
will lead us in a warning while removing dwc3.ko module.

In order to fix the situation, all we have to do is skip
dwc3_free_trb_pool() for physical endpoints 0 and 1 just
as we while deleting endpoints from the endpoints list.

Cc: stable@vger.kernel.org
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

that way we will only tell gadget framework about
the endpoints we actually have.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In DWC3 versions < 2.50a configured without
Hibernation mode enabled, there will be an
extra link status change interrupt if device
detects host-initiated U3 exit.

In that case, core will generate an unnecessary
U3 -> RESUME transition which should be ignored
by the driver.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

udc-core provides a better way to handle release
methods, let's use it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

udc-core now handles that for us, which means
we can remove it from our driver.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

udc-core now sets dma-related and parent fields
for us, we don't need to do it ourselves.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

make use of the previously introduced gadget->state
field.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

by moving to threaded IRQs, we allow our IRQ
priorities to be configurable when running with
realtime patch. Also, since we're running in
thread context, we can call functions which
might sleep, such as sysfs_notify() without
problems.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add support for basic power management on
the dwc3 driver. While there is still lots
to improve for full PM support, this minimal
patch will already make sure that we survive
suspend-to-ram and suspend-to-disk without
major issues.

Cc: Vikas C Sajjan <vikas.sajjan@linaro.org>
Tested-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This will be used during resume to verify
if we should reconnect our pullups or not.
Tested-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we don't need to enable IRQs until we have
a gadget driver loaded and ready to work,
so let's delay IRQ enable to ->udc_start()
and IRQ disable to ->udc_stop().

While at that, also move the related use of
request_irq() and free_irq().
Tested-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We don't need the ->register_my_device flag
anymore because all UDC drivers have been
properly converted.

Let's remove every history of it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We don't need to register that device ourselves
if we simply set gadget->register_my_device.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

the params variables on dwc3_gadget_conndone_interrupt()
is only memset() to zero but never used in
that function, so we can safely drop the variable
and memset() call.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

First of all, that 28 value makes no sense as
HIRD threshold is a 4-bit value, second of all
it's causing issues for OMAP5.

Using 12 because commit cbc725b3 (usb: dwc3:
keep default hird threshold value as 4b1100)
had the intention of setting the maximum allowed
value of 0xc.

Also, original code has been wrong forever, so
this should be backported as far back as
possible.

Cc: <stable@vger.kernel.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

I am not sure, why I found it during SG debugging. But, I noticed that
even when req_queued list was empty, there were some request in
request_list having queued flag true. If I run test second time, it
first removes all request from request_list and hence busy_slot was
wrongly incremented.

Cc: <stable@vger.kernel.org>
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To work with scatter gather properly, fixes have been done in number of
functions. I will explain requirement of each fixes one by one.

start_slot: used to retrieve all request of SG during cleanup

dwc3_gadget_giveback: We need to skip link TRB if it was one of the
intermediate TRB of SG.

dwc3_prepare_one_trb: We need to track all submitted TRBs during
cleanup. Since, all TRBs would be serially allocated, so we can just
keep starting slot info and we can always find rest of them. We need to
pass sg node number, so that we cab appropriately program ISOC_FIRST/ISOC,
Chain etc.

dwc3_prepare_trbs: last_one should be set when it is last node
of SG as well as last node of request_list.

__dwc3_cleanup_done_trbs: It has been prepared after re-factorization of
dwc3_cleanup_done_reqs. It is called for each TRB of SG.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

UPDATE_TRANSFER does not need any parameters. So, no need to prepare it.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When we reach to link trb, we just need to increase free_slot and then
calculate TRB. Return is not correct, as it will cause wrong TRB DMA
address to fetch in case of update transfer.

Cc: <stable@vger.kernel.org>
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There were still some corner cases where isoc transfer was not able to
restart, specially when missed isoc does not happen , and in fact gadget does
not queue any new request during giveback.

Cleanup function calls giveback first, which provides a way to queue
another request to gadget. But gadget did not had any data. So , it did
not call ep_queue. To twist it further, gadget did not queue till
cleanup for last queued TRB is called. If we ever reach this scenario,
we must call END TRANSFER, so that we receive a new  xfernotready with
information about current microframe number.

Also insure that there is no request submitted to core when issuing END
TRANSFER.

Cc: <stable@vger.kernel.org> # v3.8
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Its better to return from each if condition as they are mutually
exclusive.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There are two reasons to generate missed isoc.

1. when the host does not poll for all the data.
2. because of application-side delays that prevent all the data from
being transferred in programmed microframe.

Current code was able to handle first case only.  This patch handles
scenario 2 as well.Scenario 2 sometime may occur with complex gadget
application, however it can be easily reproduced for testing purpose as
follows:

a. use isoc binterval as 1 in f_sourcesink.
b. use pattern=0
c. introduce a delay of 150us deliberately in source_sink_complete, so
that after few frames it lands into scenario 2.
d. now run testusb 16 (isoc in  test). You will notice that if this
patch is not applied then isoc transfer is not able to recover after
first missed.

Current patch's approach is as under:

If missed isoc occurs and there is no request queued then issue END
TRANSFER, so that core generates next xfernotready and we will issue a
fresh START TRANSFER.
If there are still queued request then wait, do not issue either END or
UPDATE TRANSFER, just attach next request in request_list during giveback.
If any future queued request is successfully transferred then we will issue
UPDATE TRANSFER for all request in the request_list.

Cc: <stable@vger.kernel.org> # v3.6 v3.7 v3.8
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Synopsys says:
The HIRD Threshold field must be set to ‘0’ when the device core is
operating in super speed mode.

This patch implements above statement.

Cc: <stable@vger.kernel.org> # v3.6 v3.7 v3.8
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

dwc3_gadget_set_ep_config expects maxburst as incremented by 1. So, by
default initialize ep->maxburst to 1 for ep0.

Cc: <stable@vger.kernel.org>
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we have an extra 'ret' variable shadowing a previous
definition. Remove it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If a USB transfer has already been started, meaning
we have already issued StartTransfer command to that
particular endpoint, DWC3_EP_BUSY flag has also
already been set.

When we try to cancel this transfer which is already
in controller's cache, we will not receive XferComplete
event and we must clear DWC3_EP_BUSY in order to allow
subsequent requests to be properly started.

The best place to clear that flag is right after issuing
DWC3_DEPCMD_ENDTRANSFER.

Cc: stable@vger.kernel.org # v3.4 v3.5 v3.6
Reported-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If xfernotready is received and there is no request in request_list then
REQUEST_PENDING flag must be set, so that next request in ep queue is executed.

In case of isoc transfer, if xfernotready is already elapsed and even first
request has not been queued to request_list, then issue END TRANSFER, so that
you can receive xfernotready again and can have notion of current microframe.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case of ep0 out, if length is not aligned to maxpacket size then we use
dwc->ep_bounce_addr for dma transfer and not request->dma. Since, we have
alreday done memcpy from dwc->ep0_bounce to request->buf, so we do not need to
issue cache sync function. In fact, cache sync function will bring wrong data
in request->buf from request->dma in this scenario.

So, cache sync function must not be executed in case of ep0 bounced.

Cc: <stable@vger.kernel.org> # v3.4 v3.5
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When connection is established non-ss mode, endpoint.maxburst is correctly set
to 0, this means that current code will set maxburst bitfield on DEPCFG's
parameter 0 to the highest possible value (0x0f) which is wrong.

Even though this hasn't caused any issues so far (HW seems to ignore that when
not running in SS mode) we want to make sure maxburst bitfield is only set to
anything other than zero if we're running on SuperSpeed mode. In order to
achieve that, let's check for gadget's operating speed before setting maxburst
bitfield when issuing DEPCFG command.

[ balbi@ti.com : improved commit log a bit in order to clarify the situation ]
Signed-off-by: NChanho Park <chanho61.park@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case some gadget driver tries to enable an endpoint
which is already enabled, we print a nice WARN so we
can track broken gadget drivers. The only problem is that
we're printing the WARN when we already changed endpoint's
name, which would result in endpoints named as:

ep1in-bulk-bulk-bulk-bulk-bulk-bulk-bulk

To prevent that, we will continue to print the WARN,
but do so before changing endpoint's name and return
early.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

dwc3_stop_active_transfer has been called from two places. After each
calling of this function , we should allow 100 us delay to synchronize
with interconnect.

It would be better if we put this delay in that function only, rather
than into calling routine of this function.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Reported-by: NMichel Sanches <michel.sanches@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When MISSED_ISOC is set, BUSY is also set. Since, we are handling
MISSED_ISOC as a separate case in third scenario, therefore handle only
BUSY but not MISSED_ISOC in second scenario.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the following sparse warnings:

drivers/usb/dwc3/gadget.c:1096:7: warning: symbol 'ret' shadows an earlier one
drivers/usb/dwc3/gadget.c:1058:8: originally declared here
drivers/usb/dwc3/gadget.c:1100:16: warning: symbol 'dwc' shadows an earlier one
drivers/usb/dwc3/gadget.c:1057:15: originally declared here
drivers/usb/dwc3/gadget.c:1118:16: warning: symbol 'dwc' shadows an earlier one
drivers/usb/dwc3/gadget.c:1057:15: originally declared here
drivers/usb/dwc3/gadget.c:1800:19: warning: symbol 'dep' shadows an earlier one
drivers/usb/dwc3/gadget.c:1778:18: originally declared here

Also, fix the potential checkpatch errors around the if() loops that
this fix patch can create.
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Databook says we should set Ignore Sequence Number bit
from ConnectDone Event, so let's do so.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Although timeout has never been experienced, still to make it
meaningful, its better to return error if it ever occurs.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As per databook, ACCEPT{U1,U2}ENA bits should be set after receiving
SetConfiguration Command.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

as per databook, these bits are cleared by hardware on each USB reset,
so no need to clear it explicitly by software in reset ISR.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

as per data book any HIRD threshold value greater than 4b1100 is
invalid. So set the maximum valid value as default values.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

set_halt for ep0 is called to stall a deferred control responses by the
gadget.  We already have a function to stall default control endpoint.
This patch points set_halt for ep0 to the already available function.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NMichel Sanches <michel.sanches@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>