Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev.  The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.

I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The mode used by Windows for the Huawei E1820 will use the
same ff/ff/ff class codes for both serial and network
functions.
Reported-by: NGraham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When configuring the port (e.g. set_termios) the port minor number
rather than the port number was used in the request (and they only
coincide for minor number 0).

Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix regression introduced by commit 143d9d96 ("USB: serial: add
tiocmiwait subdriver operation") which made the ioctl operation return
ENODEV rather than ENOIOCTLCMD when a subdriver TIOCMIWAIT
implementation is missing.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 091f0ea3 "tg3: Add New 5719 Read
DMA workaround" added a workaround for TX DMA stall on the 5719. This
workaround needs to be applied to the 5720 as well.

Cc: stable@vger.kernel.org
Reported-by: NRoland Dreier <roland@purestorage.com>
Tested-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets the protocol selector bits (4:0) of the PHY's MII_ADVERTISE
register (ANAR) when writing ADVERTISE_ALL. The protocol selector bits are
indicating IEEE 803.3u support and are fixed / read-only on some PHYs. Not
setting them correctly on others (like TI DP83630) makes the PHY fall back
to 10M HDX mode which should be avoided.

Tested for TI DP83630 PHY on Microblaze platform.
Signed-off-by: NJens Renner <renner@efe-gmbh.de>
Tested-by: NMichal Simek <monstr@monstr.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was recently found out that GSO on 57710/57711 was broken, due to packets
being sent without a valid IP checksum.

Commit 057cf65e "bnx2x: Fix GSO for 57710/57711 chips" partially fixed this
issue, but failed to set the correct IP checksum when receiving GSO packets
via bridges, as such packets enter bnx2x_tx_split() and the FW flags needed
to calculate IP checksum were erroneously set in the incorrect
buffer descriptor.

This patch re-enables GSO in said scenario for 57710/57711 chips.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FW was initialized with data from wrong header, this caused TSO packets
have wrong IP csum.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAC addresses assigned by the PF to VFs were not kept in the PF driver
admin table. As a result, displaying the VF MACs from the PF interface
to user space showed zero address where in fact the VF got non-zero
address from the PF, fix that.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VF sense they didn't get MAC address, use random one. This will
address the case of administrator not assigning MAC to the VF through
the PF OS APIs and keep udev happy.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the PF initialization, SRIOV is enabled before the PF is fully initialized.
This allows the kernel to probe the newly-exposed VFs before the PF is ready
to handle them (nested probes).

Have the probe method return the -EPROBE_DEFER value in this situation (instead
of the VF probe method retrying its initialization in a loop, and returning -EIO
on failure). When -EPROBE_DEFER is returned by the VF probe method, the kernel
itself will retry the probe after a suitable delay.

Based upon a suggestion by Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When turning on adaptive_rx under adaptive moderation, the CQ's moderation
count wasn't updated according to rx_frames which resulted in too many
interrupts and bandwidth drop.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The register access to enable hardware flow control depends on the
device port number and not the port minor number.

Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the no longer used endpoint-array access completely.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The outcont_endpoints array was indexed using the port minor number
(which can be greater than the array size) rather than the device port
number.

Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove bogus port-number check in open and close, which prevented this
driver from being used with a minor number different from zero.

Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

And make the lines easier to read.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

In summary, the symptom is intermittent key events lost after resume
on some machines with synaptics touchpad (seems this is synaptics _only_),
and key events loss is due to serio port reconnect after psmouse sync lost.
Removing psmouse and inserting it back during the suspend/resume process
is able to work around the issue, so the difference between psmouse_connect()
and psmouse_reconnect() is the key to the root cause of this problem.

After comparing the two different paths, synaptics driver has its own
implementation of synaptics_reconnect(), and the missing psmouse_probe()
seems significant, the patch below added psmouse_probe() to the reconnect
process, and has been verified many times that the issue could not be reliably
reproduced.

There are two PS/2 commands in psmouse_probe():

  1. PSMOUSE_CMD_GETID
  2. PSMOUSE_CMD_RESET_DIS

Only the PSMOUSE_CMD_GETID seems to be significant. The
PSMOUSE_CMD_RESET_DIS is irrelevant to this issue after trying
several times.  So we have only implemented this patch to issue
the PSMOUSE_CMD_GETID so far.
Tested-by: NDaniel Manrique <daniel.manrique@canonical.com>
Signed-off-by: NJames M Leddy <james.leddy@canonical.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The Option GTM681W uses a qualcomm chip and can be
served by the qcserial device driver.
Signed-off-by: NRichard Weinberger <richard@nod.at>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The patch adds a new HIDCOM device and does not affect other devices
driven by the cypress_M8 module. Changes are:
- add VendorID ProductID to device tables
- skip unstable speed check because FRWD uses 115200bps
- skip reset at probe which is an issue workaround for this
particular device.
Signed-off-by: NRobert Butora <robert.butora.fi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

smatch reports the following warnings:
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:514 pcan_usb_pro_drv_loaded() error: doing dma on the stack (buffer)
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:878 pcan_usb_pro_init() error: doing dma on the stack (&fi)
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:889 pcan_usb_pro_init() error: doing dma on the stack (&bi)

See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?"

Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

smatch reports the following warnings:
drivers/net/can/usb/esd_usb2.c:640 esd_usb2_start() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:846 esd_usb2_close() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:855 esd_usb2_close() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:923 esd_usb2_set_bittiming() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:1047 esd_usb2_probe() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:1053 esd_usb2_probe() error: doing dma on the stack (&msg)

See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?"
Signed-off-by: NOlivier Sobrie <olivier@sobrie.be>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Unlike Kvaser Leaf light devices, some other Kvaser devices (like USBcan
Pro, USBcan R) receive CAN messages in CMD_LOG_MESSAGE frames. This
patch adds support for it.

Cc: linux-stable <stable@vger.kernel.org> # >= v3.8
Signed-off-by: NJonas Peterson <jonas.peterson@gmail.com>
Signed-off-by: NOlivier Sobrie <olivier@sobrie.be>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The driver's interrupt handling code is too picky in deciding whether it should
handle an interrupt or not which causes completely unneeded spurious interrupts.
Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read
to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't
get cleared by writing to the SATAINTSTAT register in the interrupt mode we use.

Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for
enabled interrupts and we should clear  only those interrupts  that we have read
as active first time around, because else we have  a  race and risk clearing  an
interrupt that  can  occur between read  and write of the  SATAINTSTAT  register
and never registering it...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

Fix the above kernel error from parport_announce_port() on 32bit GSC
machines (e.g. B160L). The parport driver requires now a pointer to the
device struct.
Signed-off-by: NHelge Deller <deller@gmx.de>

If enabled, CONFIG_PARPORT_PC_SUPERIO scans on PC-like hardware for
various super-io chips by accessing i/o ports in a range which will
crash any parisc hardware at once.

In addition, parisc has it's own incompatible superio chip
(CONFIG_SUPERIO), so if we disable PARPORT_PC_SUPERIO completely for
parisc we can avoid that people by accident enable the parport_pc
superio option too.
Signed-off-by: NHelge Deller <deller@gmx.de>

commit dc7dce28
Author: Bjorn Helgaas <bhelgaas@google.com>
Date:   Fri Oct 28 16:27:27 2011 -0600
   parisc/PCI: lba: convert to pci_create_root_bus() for correct root bus
                    resources

  Supply root bus resources to pci_create_root_bus() so they're correct
  immediately.  This fixes the problem of "early" and "header" quirks seeing
  incorrect root bus resources.

added tests for elmmio_space.start while it should use
elmmio_space.flags.  This for example led to incorrect resource
assignments and a non-working stifb framebuffer on most parisc machines.

LBA 10:1: PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [io  0x12000-0x13fff] (bus address [0x2000-0x3fff])
pci_bus 0000:01: root bus resource [mem 0xfffffffffa000000-0xfffffffffbffffff] (bus address [0xfa000000-0xfbffffff])
pci_bus 0000:01: root bus resource [mem 0xfffffffff4800000-0xfffffffff4ffffff] (bus address [0xf4800000-0xf4ffffff])
pci_bus 0000:01: root bus resource [??? 0x00000001 flags 0x0]
Signed-off-by: NHelge Deller <deller@gmx.de>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>

The non-PAT resource probing code failed to set the type of the LBA bus_num
resource (30aa80da "parisc/PCI: register busn_res for root buses" did
the corresponding thing for the PAT case).

This causes incorrect resource assignments and a non-working stifb
framebuffer on most parisc machines.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NHelge Deller <deller@gmx.de>

Since the recent addition of 8021AD, we need to set the new field vlan_proto in
sk_buff. Otherwise, it will trigger BUG() call in vlan_proto_idx().

This patch fixes the problem.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case the port list dump does not fit into one skb currently the
dump would start over again. Fix this by continue from the last dumped
port.

Introduced by commit d90f889e (team: handle sending port list in the
same way option list is sent)
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

worse, we lock ->resource_lock too late when we are destroying the
final clonal VMA; the check for lack of other mappings of the same
opened file can race with mmap().
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

When removing atmel_lcdfb module, the backlight is unregistered but not
blanked. (only for CONFIG_BACKLIGHT_ATMEL_LCDC case).
This can result in the screen going full white depending on how the PWM
is wired.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

When a too small framebuffer is given, the atmel_lcdfb_check_var
silently fails.
Adding an error message will save some head scratching.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

That patch failed to set proc_scsi_fops' .release method.
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

When a path is gone and dasd_generic_path_event is called with a
PE_PATH_GONE event, we must assume that any I/O request on that
subchannel is still running. This is unlike the dasd_generic_notify
handler and the CIO_NO_PATH event, which implies that the subchannel
has been cleared.
If dasd_generic_path_event finds that the path has been the last
usable path, it must not call dasd_generic_last_path_gone (which would
reset the state of running requests), but just set the
DASD_STOPPED_DC_WAIT bit.
Signed-off-by: NStefan Weinhuber <wein@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

With the introduction of target_get_sess_cmd() referencing counting for
ISCSI_OP_SCSI_CMD processing with iser-target, iscsit_free_cmd() usage
in traditional iscsi-target driver code now needs to be aware of the
active I/O shutdown case when a remaining se_cmd->cmd_kref reference may
exist after transport_generic_free_cmd() completes, requiring a final
target_put_sess_cmd() to release iscsi_cmd descriptor memory.

This patch changes iscsit_free_cmd() to invoke __iscsit_free_cmd() before
transport_generic_free_cmd() -> target_put_sess_cmd(), and also avoids
aquiring the per-connection queue locks for typical fast-path calls
during normal ISTATE_REMOVE operation.

Also update iscsit_free_cmd() usage throughout iscsi-target to
use the new 'bool shutdown' parameter.

This patch fixes a regression bug introduced during v3.10-rc1 in
commit 3e1c81a9, that was causing the following WARNING to appear:

[  257.235153] ------------[ cut here]------------
[  257.240314] WARNING: at kernel/softirq.c:160 local_bh_enable_ip+0x3c/0x86()
[  257.248089] Modules linked in: vhost_scsi ib_srpt ib_cm ib_sa ib_mad ib_core tcm_qla2xxx tcm_loop
	tcm_fc libfc iscsi_target_mod target_core_pscsi target_core_file
	target_core_iblock target_core_mod configfs ipv6 iscsi_tcp libiscsi_tcp
	libiscsi scsi_transport_iscsi loop acpi_cpufreq freq_table mperf
	kvm_intel kvm crc32c_intel button ehci_pci pcspkr joydev i2c_i801
	microcode ext3 jbd raid10 raid456 async_pq async_xor xor async_memcpy
	async_raid6_recov raid6_pq async_tx raid1 raid0 linear igb hwmon
	i2c_algo_bit i2c_core ptp ata_piix libata qla2xxx uhci_hcd ehci_hcd
	mlx4_core scsi_transport_fc scsi_tgt pps_core
[  257.308748] CPU: 1 PID: 3295 Comm: iscsi_ttx Not tainted 3.10.0-rc2+ #103
[  257.316329] Hardware name: Intel Corporation S5520HC/S5520HC, BIOS S5500.86B.01.00.0057.031020111721 03/10/2011
[  257.327597]  ffffffff814c24b7 ffff880458331b58 ffffffff8138eef2 ffff880458331b98
[  257.335892]  ffffffff8102c052 ffff880400000008 0000000000000000 ffff88085bdf0000
[  257.344191]  ffff88085bdf00d8 ffff88085bdf00e0 ffff88085bdf00f8 ffff880458331ba8
[  257.352488] Call Trace:
[  257.355223]  [<ffffffff8138eef2>] dump_stack+0x19/0x1f
[  257.360963]  [<ffffffff8102c052>] warn_slowpath_common+0x62/0x7b
[  257.367669]  [<ffffffff8102c080>] warn_slowpath_null+0x15/0x17
[  257.374181]  [<ffffffff81032345>] local_bh_enable_ip+0x3c/0x86
[  257.380697]  [<ffffffff813917fd>] _raw_spin_unlock_bh+0x10/0x12
[  257.387311]  [<ffffffffa029069c>] iscsit_free_r2ts_from_list+0x5e/0x67 [iscsi_target_mod]
[  257.396438]  [<ffffffffa02906c5>] iscsit_release_cmd+0x20/0x223 [iscsi_target_mod]
[  257.404893]  [<ffffffffa02977a4>] lio_release_cmd+0x3a/0x3e [iscsi_target_mod]
[  257.412964]  [<ffffffffa01d59a1>] target_release_cmd_kref+0x7a/0x7c [target_core_mod]
[  257.421712]  [<ffffffffa01d69bc>] target_put_sess_cmd+0x5f/0x7f [target_core_mod]
[  257.430071]  [<ffffffffa01d6d6d>] transport_release_cmd+0x59/0x6f [target_core_mod]
[  257.438625]  [<ffffffffa01d6eb4>] transport_put_cmd+0x131/0x140 [target_core_mod]
[  257.446985]  [<ffffffffa01d6192>] ? transport_wait_for_tasks+0xfa/0x1d5 [target_core_mod]
[  257.456121]  [<ffffffffa01d6f11>] transport_generic_free_cmd+0x4e/0x52 [target_core_mod]
[  257.465159]  [<ffffffff81050537>] ? __migrate_task+0x110/0x110
[  257.471674]  [<ffffffffa02904ba>] iscsit_free_cmd+0x46/0x55 [iscsi_target_mod]
[  257.479741]  [<ffffffffa0291edb>] iscsit_immediate_queue+0x301/0x353 [iscsi_target_mod]
[  257.488683]  [<ffffffffa0292f7e>] iscsi_target_tx_thread+0x1c6/0x2a8 [iscsi_target_mod]
[  257.497623]  [<ffffffff81047486>] ? wake_up_bit+0x25/0x25
[  257.503652]  [<ffffffffa0292db8>] ? iscsit_ack_from_expstatsn+0xd5/0xd5 [iscsi_target_mod]
[  257.512882]  [<ffffffff81046f89>] kthread+0xb0/0xb8
[  257.518329]  [<ffffffff81046ed9>] ? kthread_freezable_should_stop+0x60/0x60
[  257.526105]  [<ffffffff81396fec>] ret_from_fork+0x7c/0xb0
[  257.532133]  [<ffffffff81046ed9>] ? kthread_freezable_should_stop+0x60/0x60
[  257.539906] ---[ end trace 5520397d0f2e0800 ]---
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Go ahead and propigate up the ->cmd_kref put return value from
target_put_sess_cmd() -> transport_release_cmd() -> transport_put_cmd()
-> transport_generic_free_cmd().

This is useful for certain fabrics when determining the active I/O
shutdown case with SCF_ACK_KREF where a final target_put_sess_cmd()
is still required by the caller.
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Just the usual printk related warnings.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fix the following sparse warnings:

drivers/clk/mxs/clk-imx28.c:72:5: warning: symbol 'mxs_saif_clkmux_select' was not declared. Should it be static?
drivers/clk/mxs/clk-imx28.c:156:12: warning: symbol 'mx28_clocks_init' was not declared. Should it be static?
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: fixed $SUBJECT line]